Sub250 Send T400 VTX

Contents

Sub250 Send T400 VTX Instruction Manual

High-Performance Video Transmitter for FPV Drones

1. Introduction

The Sub250 Send T400 VTX is a lightweight video transmitter specifically designed for FPV drones, particularly those under 250g. It offers straightforward operation with button-based frequency and power adjustments, as well as serial port control via a flight controller's OSD. The VTX features 7 LEDs for clear indication of current frequency and power status. It utilizes a standard UFL antenna interface and incorporates a temperature control system to prevent overheating.

2. Safety Information

  • Always ensure the antenna is securely connected to the VTX before powering on. Operating without an antenna can permanently damage the unit.
  • Verify that the input voltage matches the VTX's requirements (5V). Incorrect voltage can cause damage.
  • Avoid touching the VTX during operation as it may become hot. Allow it to cool before handling.
  • Keep the VTX away from water, moisture, and extreme temperatures.
  • Ensure proper ventilation to aid the temperature control system.
  • Handle with care to prevent damage to delicate electronic components.

3. Setup Guide

3.1 Package Contents

Please check the package to ensure all items are present:

  • 1 x Sub250 Send T400 VTX
  • 1 x SH1.0 4-pin cable
  • 1 x 5.8G antenna (50mm)

3.2 Physical Installation

The Send T400 VTX features a compact design with specific mounting dimensions:

  • Mounting Hole Pattern: 25.5mm x 25.5mm (M2)
Sub250 Send T400 VTX with 25.5mm x 25.5mm mounting hole dimensions
Figure 3.2.1: VTX Mounting Dimensions (25.5mm x 25.5mm)
Sub250 Send T400 VTX overall dimensions: 29.6mm, 40mm, 21mm
Figure 3.2.2: VTX Overall Dimensions

Secure the VTX to your drone's frame using appropriate M2 screws, ensuring it is isolated from vibrations and potential short circuits.

3.3 Wiring Diagram

Connect the VTX to your flight controller or power distribution board using the provided SH1.0 4-pin cable. The input voltage required is 5V. Refer to the labels on the VTX for correct pin assignments:

  • 5V: Power input (connect to 5V output from FC/PDB)
  • G: Ground (connect to Ground from FC/PDB)
  • VTX: Video signal output (connect to video input on FC)
  • RX: Serial data input (connect to a free TX pad on your FC for OSD control)
Front view of Sub250 Send T400 VTX showing 5V, Ground, VTX, and RX connection points
Figure 3.3.1: VTX Connection Points

3.4 Antenna Connection

Attach the provided 5.8G antenna to the UFL connector on the VTX. Ensure a firm connection. Always connect the antenna before applying power to the VTX to prevent damage.

4. Operating Instructions

4.1 Powering On

Once properly wired and the antenna is connected, power on your FPV drone. The VTX will power on simultaneously with the flight controller.

4.2 Adjusting Frequency and Power

The Send T400 VTX offers two methods for adjustment:

  • Button Control: A button on the VTX allows you to cycle through frequency bands, channels, and power levels (PitMode/25mW/200mW/400mW). Refer to the LED indicators for the current selection.
  • OSD Control (IRC Tramp Protocol): Connect the VTX's RX pin to a TX pad on your flight controller and configure the serial port in your flight controller software (e.g., Betaflight, Emuflight). This enables VTX control directly from your FPV goggles' On-Screen Display (OSD) menu.
Top view of Sub250 Send T400 VTX showing the control button and LED indicators
Figure 4.2.1: VTX Control Button and LEDs

4.3 LED Indicators

The VTX features 7 LEDs that provide visual feedback on the selected frequency band, channel, and output power. Consult your flight controller's OSD or the VTX's specific LED pattern guide (if available in FC software documentation) for detailed interpretation.

4.4 PitMode

PitMode allows the VTX to transmit at a very low power level, typically for safe testing or setup without interfering with other pilots. Activate PitMode when working on your drone in close proximity to others.

5. Maintenance

  • Cleaning: Keep the VTX free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Temperature Management: The VTX includes a temperature control system. Ensure adequate airflow around the unit, especially when operating at higher power levels, to prevent it from throttling down or shutting off due to excessive heat.
  • Connection Integrity: Regularly check all cable and antenna connections for looseness or damage.
  • Firmware Updates: While not explicitly mentioned, some VTXs support firmware updates via the flight controller. Check the manufacturer's website or flight controller documentation for any available updates.

6. Troubleshooting

ProblemPossible CauseSolution
No video signalAntenna not connected, incorrect wiring, VTX not powered, incorrect frequency/channel.Ensure antenna is connected. Check 5V and Ground wiring. Verify VTX is receiving power. Match VTX frequency/channel to receiver.
Poor video quality (static, lines)Loose antenna, interference, low power output, damaged VTX/antenna.Secure antenna connection. Change frequency/channel to avoid interference. Increase VTX power output. Inspect VTX and antenna for damage.
VTX gets excessively hotInsufficient airflow, high power output in confined space, faulty unit.Ensure proper ventilation. Consider lowering power output if not needed. If problem persists, contact support.
Cannot change settings via OSDIncorrect serial port wiring, FC software not configured for IRC Tramp, incorrect UART selected.Verify RX to TX wiring. Enable VTX (IRC Tramp) on the correct UART in Betaflight/Emuflight configurator.

7. Specifications

FeatureDetail
ModelSend T400
BrandSub250
Input Voltage5V
Input Impedance75Ω
ProtocolIRC Tramp
Antenna ConnectorUFL
Cable ConnectorSH1.0
Output PowerPitMode/25mW/200mW/400mW
Frequency48ch
MicrophoneNo
Mounting Hole25.5mm x 25.5mm (M2)
Weight2g
MaterialComposite Material
For Vehicle TypeAirplanes
Recommended Age14+ years
Sub250 Send T400 VTX on a digital scale, showing a weight of 2.0 grams
Figure 7.1: VTX Weight (2.0g)

8. User Tips

  • Antenna First: Always connect your antenna before powering on the VTX to prevent immediate damage.
  • OSD Configuration: Utilize the OSD control feature (IRC Tramp protocol) for convenient frequency and power adjustments directly from your FPV goggles. This is often easier than using the physical button, especially after installation.
  • PitMode for Safety: When working on your drone or flying with others, use PitMode to avoid interfering with other pilots' video feeds.
  • Heat Management: While the VTX has a temperature control system, ensure it has adequate airflow, especially when running at 400mW, to maintain optimal performance and longevity.
  • Check for Updates: Periodically check the Sub250 website or relevant FPV forums for any firmware updates that might improve performance or add features.

9. Warranty and Support

For warranty claims, technical support, or any questions not covered in this manual, please contact the seller or manufacturer directly. Keep your proof of purchase for warranty purposes.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.