1. Product Overview
This manual provides instructions for various HWATEL multi-band antennas designed to enhance cellular and WiFi signals (2G, 3G, 4G, 5G, WIFI) within the 700-6000 MHz frequency range. These antennas are integral components of cellular amplifier, booster, and repeater systems, designed to capture and distribute signals effectively.
Antenna Types and Components

2. Setup and Installation
Proper installation is crucial for optimal performance of your cellular signal amplification system. Follow these steps carefully:
- Identify Signal Source: Locate an area with the strongest existing cellular signal. This is where your outdoor antenna will be installed.
- Install Outdoor Antenna: Mount the outdoor antenna securely in the chosen location. Ensure it is directed towards the nearest cell tower for best reception.
- Connect Outdoor Antenna to Signal Booster: Use an appropriate RG-58 cable (or specified cable for your antenna type) to connect the outdoor antenna to the designated 'Outdoor' or 'BTS' port on your signal booster/repeater.
- Install Indoor Antenna: Position the indoor antenna in the area where you need improved signal coverage. Ensure there is adequate separation between the outdoor and indoor antennas to prevent oscillation.
- Connect Indoor Antenna to Signal Booster: Connect the indoor antenna to the 'Indoor' or 'Mobile' port on your signal booster/repeater using the provided cable.
- Power On: Once all connections are secure, connect the power adapter to the signal booster and plug it into an electrical outlet.
Installation and Signal Improvement Demonstration
3. Operating Instructions
After successful installation, your HWATEL antenna system should begin amplifying signals automatically. The signal booster unit (not included with all antenna purchases) will typically have indicator lights or a display to show operational status and signal strength.
- Signal Strength Monitoring: Use your mobile device's signal strength indicator (often found in 'Settings > About Phone > SIM status' or similar) to verify signal improvement. Signal strength is typically measured in dBm (decibel-milliwatts), where a number closer to 0 (e.g., -50 dBm) indicates a stronger signal than a number further from 0 (e.g., -100 dBm).
- Network Type: Ensure your phone is set to the desired network type (e.g., LTE for 4G, HSPA for 3G, GSM for 2G) to observe the specific signal improvements.
Signal Strength Observation
The demonstration video illustrates the signal strength before and after powering on the booster:
- Before Power On (2G/3G): Signal strength was approximately -89 dBm (12 asu).
- After Power On (2G/3G): Signal strength improved significantly to approximately -51 dBm (31 asu).
- Before Power On (4G LTE): Signal strength was approximately -107 dBm (33 asu).
- After Power On (4G LTE): Signal strength improved significantly to approximately -55 dBm (85 asu).
4. Maintenance
HWATEL antennas are designed for durability and require minimal maintenance. However, periodic checks can ensure continued optimal performance:
- Visual Inspection: Regularly inspect the outdoor antenna and cables for any physical damage, corrosion, or loose connections, especially after severe weather conditions.
- Cable Integrity: Ensure all cables are securely connected and free from kinks or damage. Damaged cables can significantly degrade signal quality.
- Mounting Stability: Verify that the outdoor antenna mount is stable and secure.
- Cleaning: Gently clean the antenna surface if it accumulates excessive dirt or debris, which could potentially interfere with signal reception. Use a soft, damp cloth.
5. Troubleshooting
If you experience issues with your signal amplification system, consider the following troubleshooting steps:
- No Signal Improvement:
- Check Connections: Ensure all cables are correctly and securely connected to both antennas and the signal booster.
- Antenna Alignment: For directional antennas (like LOG or Panel), ensure the outdoor antenna is precisely aimed at the nearest cell tower. Slight adjustments can make a significant difference.
- Isolation: Ensure sufficient physical separation (both horizontal and vertical) between the outdoor and indoor antennas to prevent feedback (oscillation).
- Outdoor Signal Strength: Verify that the outdoor antenna location has a strong enough signal to be amplified. If the outdoor signal is too weak, the booster may not be able to amplify it effectively.
- Intermittent Signal:
- Loose Connections: Check for any loose cable connections.
- Interference: Ensure there are no new sources of electromagnetic interference near the antennas or booster.
- Power Issues:
- Power Supply: Confirm the signal booster is receiving power and its power indicator light is on. Check the power adapter and outlet.
6. Specifications
HWATEL offers a range of antennas with varying specifications. Please refer to the specific product variant for exact details. General specifications are provided below:
| Feature | Description |
|---|---|
| Type | LOG, Panel, Omni, Rocket, Rod, Ceiling, Whip Antennas |
| Frequency Range | 700-6000 MHz (Specific range varies by model, e.g., 600-3700MHz, 700-4000MHz, 700-5300MHz, 600-6000MHz) |
| Supported Technologies | 2G, 3G, 4G, 5G, WIFI |
| Gain | Varies by model (e.g., 7-12dBi, 9-12dB, 12dBi, 12-20dB, 14-30dB, 20/24/30dB) |
| Cable Type | RG-58, RG-174 (Varies by model) |
| Connector Type | N Female, N Male, SMA Male (Varies by model) |
| Certification | CE, FCC |
| Origin | Mainland China |
Antenna Type Specifics



7. Warranty and Support
For product support, technical assistance, or warranty inquiries, please contact HWATEL ZBOOSTER Store directly through the platform where the purchase was made. Keep your purchase records for faster service.