EASWEL 1T4 Wiring Harness Cable

Contents

EB-BUS 1T4 Wiring Harness Cable User Manual

For BAFANG eBike BBS01B, BBS02B, and BBSHD Mid Motor Kits

Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your EB-BUS 1T4 Wiring Harness Cable. This cable is designed to integrate various eBike components with BAFANG BBS01B, BBS02B, and BBSHD mid-drive motor kits, ensuring reliable communication and power distribution.

Specifications

FeatureSpecification
Brand NameEASWEL
Model NumberDATA
IP-CodeIP 65
SuitabilityEB-BUS
Length136cm (53.93inch)
Wire Specification (AWG)24
Operating Temperature-20 - 45℃
Pin Surface TreatmentGold Plating
Waterproof ConnectorMale 8Pin (M8.4)
CertificationROHS
CompatibilityBafang BBS01B, BBS02B, BBSHD Motor Conversion Kit
USB TypeStandard
UseSmart Devices
OriginMainland China

Setup and Installation

The EB-BUS 1T4 wiring harness is designed for straightforward connection to your Bafang mid-motor system. It provides four branching connections for your eBike's display, left brake, right brake, and throttle.

EB-BUS 1T4 Wiring Harness Cable with its five connectors. The main cable connects to the mid-motor, and four branches connect to the display, left brake, right brake, and throttle.
EB-BUS 1T4 Wiring Harness Cable showing the main connector and four accessory connectors.

Connection Points:

  1. Pin A (Green 5 Pins): Connects to your eBike's Display (G5.2).
  2. Pin B (Female Yellow 3 Pins): Connects to the Left Brake lever.
  3. Pin C (Female Yellow 3 Pins): Connects to the Right Brake lever.
  4. Pin D (Male Yellow 3 Pins): Connects to the Throttle.
  5. Pin E (Male 8 Pins, M8.4): This is the main cable that connects directly to your Bafang Mid Motor.

Installation Steps:

  1. Ensure Power is Off: Before beginning any installation, ensure your eBike's battery is disconnected and the system is powered off to prevent electrical damage or injury.
  2. Identify Connectors: Match each connector on the 1T4 harness to its corresponding component (display, brake levers, throttle, and motor). The connectors are color-coded and have distinct pin configurations to prevent incorrect connections.
  3. Connect to Motor: First, connect the main 8-pin (M8.4) connector (Pin E) of the 1T4 harness to the main cable port on your Bafang mid-motor. Ensure it is firmly seated.
  4. Connect Accessories: Proceed to connect the remaining four branches: the green 5-pin connector (Pin A) to your display, the yellow 3-pin female connectors (Pin B and C) to your left and right brake levers, and the yellow 3-pin male connector (Pin D) to your throttle.
  5. Secure Connections: Gently push each connector until it clicks or feels securely seated. Do not force connections. The waterproof design ensures a snug fit.
  6. Cable Management: Route the cables neatly along your eBike frame, securing them with zip ties or cable clips to prevent snagging, rubbing, or damage during riding. Ensure cables do not interfere with moving parts like wheels or pedals.
  7. Test System: Once all connections are made and secured, reconnect your eBike battery and power on the system. Test the functionality of your display, brake cut-off sensors, and throttle to ensure everything is working correctly.

Operating Instructions

The EB-BUS 1T4 Wiring Harness Cable functions as a passive component, facilitating communication and power flow between your Bafang mid-motor and connected eBike accessories. Once correctly installed, no specific operational steps are required for the cable itself. Its operation is integrated with the functionality of the connected display, brake levers, and throttle.

Ensure that all connected components are functioning as expected. If any component fails to respond, refer to the Troubleshooting section.

Maintenance

Proper maintenance of your wiring harness will ensure its longevity and reliable performance.

  • Regular Inspection: Periodically inspect the entire length of the cable and all connectors for any signs of wear, cuts, abrasions, or corrosion.
  • Keep Clean and Dry: While the connectors are waterproof (IP 65), it is good practice to keep them clean and dry. If they become dirty, gently wipe them with a clean, damp cloth and ensure they are dry before use.
  • Avoid Stress: Do not pull on the cables excessively or subject them to sharp bends, which can damage the internal wiring. Ensure cables are routed without tension.
  • Connector Care: If disconnecting connectors, do so carefully by gripping the connector body, not the wires. Ensure pins are not bent or damaged during reconnection.

Troubleshooting

If you experience issues with your eBike system after installing the 1T4 wiring harness, consider the following troubleshooting steps:

  • No Power to Components / System Not Turning On:
    • Verify that the main 8-pin connector (Pin E) is securely connected to the Bafang mid-motor.
    • Check your eBike battery connection and ensure it is charged.
  • Display Not Working:
    • Ensure the green 5-pin display connector (Pin A) is fully seated and undamaged.
    • Check the display unit itself for any faults.
  • Brakes Not Cutting Motor Power:
    • Confirm that both yellow 3-pin female brake connectors (Pin B and C) are correctly attached to their respective brake levers.
    • Inspect the brake levers' sensors for proper function.
  • Throttle Unresponsive:
    • Check the yellow 3-pin male throttle connector (Pin D) for a secure connection.
    • Test the throttle unit independently if possible.
  • Intermittent Issues or Erratic Behavior:
    • Disconnect and reconnect all connectors to ensure they are fully seated and making good contact.
    • Inspect all pins within the connectors for bending or corrosion.
    • Check the cable for any visible damage or kinks along its length.

If problems persist after these steps, it is recommended to consult a professional eBike technician or contact the seller for further assistance.

User Tips

  • Always ensure the eBike power is off before connecting or disconnecting any cables to prevent short circuits or damage to electronic components.
  • Consider applying a small amount of dielectric grease to the connector pins before assembly. This can improve water resistance, prevent corrosion, and make future disconnections easier.
  • Proper cable routing is essential. Use zip ties or specialized cable wraps to secure the harness along the frame, keeping it away from moving parts, sharp edges, and potential pinch points.
  • When disconnecting, always pull on the connector body, not the wires, to avoid damaging the wire-to-connector crimp.

Warranty and Support

Your EB-BUS 1T4 Wiring Harness Cable comes with the following guarantees:

  • 30 Days Money Back Guarantee: If you are not satisfied with your purchase, you may be eligible for a full refund within 30 days of receipt.
  • 180 Days - Free Exchange: In case of product defects or malfunctions, a free exchange may be provided within 180 days from the date of purchase.

For any questions, concerns, or to initiate a warranty claim, please contact the seller directly. Provide your purchase details and a clear description of the issue for prompt assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.