Bykski N-RTX5090FE-SR

Contents

Bykski N-RTX5090FE-SR GPU Water Block User Manual

Model: N-RTX5090FE-SR

Compatible with NVIDIA Geforce RTX 5090 Founders Edition Graphics Card

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Bykski N-RTX5090FE-SR GPU Water Block. This product is designed to provide efficient liquid cooling for NVIDIA Geforce RTX 5090 Founders Edition graphics cards, enhancing thermal performance and stability.

2. Package Contents

Please verify that all items listed below are present in your package:

  • Water Block *1
  • Thermal Pad* 1 Set
  • Water Plug* 2
  • Mount Screws, Nut, Spring* 1 Set
  • Manual *1 (This document)

For a visual reference of the product and its packaging, please refer to the video below:

Video: Bykski GPU water block packaging and product views.

3. Specifications

Feature Detail
Brand Name Bykski
Model Number N-RTX5090FE-SR
Type VGA Front Water Block
Compatible Graphics Card NVIDIA Geforce RTX 5090 Founders Edition
Material Copper + Stainless Steel + POM
Thread G1/4
RGB Support NO RGB
Compression Fittings Included No
Origin Mainland China
Certification NONE
Product Dimensions (approx.) Length: 234.35mm / 222.16mm, Width: 121.82mm, Height: 22.70mm / 10.96mm
Package Dimensions (approx.) Length: 24 cm, Width: 17 cm, Height: 16 cm
Package Weight (approx.) 1.6 kg
Diagram showing dimensions of the Bykski GPU Water Block

Figure 3.1: Product Dimensions Diagram (in mm)

4. Setup and Installation

Important: Installation of a GPU water block requires technical proficiency. If you are unsure about any steps, please seek professional assistance to avoid damaging your graphics card or the water block.

Before starting, ensure your workspace is clean and static-free. Gather all necessary tools, including screwdrivers, thermal paste/pads, and cleaning supplies.

4.1. Preparation

  1. Remove Original Cooler: Carefully remove the original cooling solution from your graphics card. This typically involves unscrewing the mounting screws and detaching any fan headers or RGB cables.
  2. Clean GPU: Thoroughly clean any residual thermal paste or thermal pads from the GPU die, memory chips, and VRMs using isopropyl alcohol and a lint-free cloth.
  3. Apply Thermal Interface Material:
    • Apply a thin, even layer of thermal grease to the GPU die.
    • Cut the provided thermal pads to the appropriate sizes and place them on the memory chips and VRMs as indicated in the installation diagram.

4.2. Water Block and Backplate Installation

Refer to the installation diagram below for visual guidance:

Exploded view diagram of the Bykski GPU Water Block with installation steps and parts list

Figure 4.1: Installation Diagram and Parts List

  1. Mount Water Block:
    • Insert the standoffs into the designated screw posts on the water block.
    • Carefully align the water block with the graphics card, ensuring the screw posts on the water block align with the screw holes on the GPU PCB.
    • Gently lower the water block onto the GPU. If the water block does not align easily, do not force it. Recheck alignment to prevent damage to the graphics card.
  2. Install Backplate (if applicable):
    • Place the backplate on the rear side of the graphics card, aligning it with the screw holes.
    • Apply insulating pads to the corresponding screw hole positions on the backplate.
    • Secure the backplate and water block by tightening the spring screws and backplate screws into the aligned holes. Tighten screws in a diagonal pattern to ensure even pressure.

4.3. Installation Parts List

Item No. Description Quantity
① N-RTX5090FE-SR Water Block 1 PCS
② 1.5 MM Thermal Pad 5 Strips
③ PCB (Graphics Card Printed Circuit Board) 1 PCS (Reference)
④ 0.5 MM Spacer 4 PCS
⑤ Spring Screw 4 PCS
⑥ Water Cooling Backplate 1 PCS
⑦ Backplate Screws 4 PCS
⑧ PCB Golden Finger (GPU Connector) 1 PCS (Reference)
⑨ Original GPU Bracket 1 PCS (Reference)
⑩ M2*5 MM Cross Flat Screw 8 PCS
⑪ M1.5*4 MM Cross Flat Screw 2 PCS
⑫ Backplate Accessories 2 PCS
⑬ M2*3 MM Flat Head Screw 8 PCS
⑭ PCI-E Baffle (GPU Slot Cover) 1 PCS (Reference)
⑮ M3*5 MM Flat Head Screw 3 PCS

5. Operating Instructions

Once the water block is securely installed on your graphics card and integrated into your custom liquid cooling loop, follow these steps:

  1. Fill and Bleed Loop: Fill your liquid cooling loop with appropriate coolant and carefully bleed all air from the system. This may involve tilting your PC case and running the pump at varying speeds.
  2. Leak Testing: Before powering on your PC, perform a leak test. It is highly recommended to use an air pressure tester or run the pump with only the power supply connected (jump-starting the PSU) for at least 24 hours to check for any leaks. Place paper towels under all connections to easily spot drips.
  3. Power On and Monitor: After confirming no leaks, power on your PC. Install monitoring software to observe GPU temperatures, coolant temperatures, and pump/fan speeds. Ensure temperatures remain within safe operating limits during idle and load conditions.

6. Maintenance

Regular maintenance is crucial for the longevity and performance of your liquid cooling system:

  • Inspect for Leaks: Periodically check all fittings, tubing, and the water block for any signs of leaks or coolant discoloration.
  • Coolant Replacement: Replace the coolant every 6-12 months, or as recommended by your coolant manufacturer, to prevent buildup and maintain optimal performance.
  • Clean Water Block: Over time, sediment or biological growth can accumulate inside the water block. Disassemble the water block and clean the micro-fins with a soft brush and distilled water if flow restriction or performance degradation is observed.
  • Dust Removal: Keep radiators and fans clean from dust to ensure efficient heat dissipation.

7. Troubleshooting

If you encounter issues with your water block, consider the following:

  • High GPU Temperatures:
    • Check thermal paste application: Ensure even coverage and sufficient contact pressure.
    • Verify thermal pad placement: Make sure all critical components (memory, VRMs) have proper thermal pad contact.
    • Inspect coolant flow: Ensure the pump is running, there are no kinks in tubing, and the reservoir has sufficient coolant.
    • Bleed air: Air bubbles trapped in the loop can impede flow and cooling.
  • Leaks:
    • Immediately shut down the system.
    • Identify the source of the leak. Tighten fittings, replace O-rings, or re-seat components as necessary.
    • Ensure all components are dry before restarting.
  • No Flow/Poor Flow:
    • Check pump power and functionality.
    • Inspect for blockages in the loop (e.g., debris, excessive coolant additives).
    • Ensure tubing is not kinked.

8. User Tips

  • Always perform a thorough leak test before powering on your system after any liquid cooling installation or maintenance.
  • Use high-quality coolant to prevent corrosion and biological growth in your loop.
  • Consider using a flow indicator in your loop to easily monitor coolant movement.
  • When tightening screws, use a diagonal pattern to ensure even pressure distribution and prevent warping.

9. Warranty and Support

For warranty information and technical support, please refer to the official Bykski website or contact your retailer. Keep your proof of purchase for warranty claims.

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.