1. Product Overview
The AIFEN-A99HD is a high-power electric tweezers soldering station designed for precision electronic rework. It supports both 210 electric tweezers and 210/245 single handles, offering dual-channel detection and a maximum power output of 320W. The station features a color screen UI for convenient system settings and real-time temperature display.


2. Setup Instructions
2.1. Connecting the Handles
Attention: When connecting and disconnecting the handle, always turn off the power to avoid damaging the control circuit board.
- Connect the handle to the handle socket on the host.
- Install the required heating element for the device.
- Arrange the welding table and place the handle on the handle holder.
- Connect the power supply properly.
- Turn on the power switch. The display window will show "sleep", indicating the soldering station is in standby mode.
2.2. Important Compatibility Note
The AIFEN-A99HD soldering station is NOT compatible with handles that have integrated buttons. Using such handles will cause the buttons to burn out. Only use the single-handle version without buttons.

3. Operating Instructions
3.1. Temperature Setting and Storage
Heating Up:
- Press the "^" key once to increase the set temperature by 1°C.
- Hold down the "^" key for at least one second for rapid temperature increase until the desired temperature is reached.
Cooling Down:
- Press the "v" key once to decrease the set temperature by 1°C.
- Hold down the "v" key for at least one second for rapid temperature decrease until the desired temperature is reached.
Storing and Recalling Memory:
- Storage: After setting the desired temperature, select the channel (CH1, CH2, CH3, or CH4) and long-press the corresponding button to save the setting.
- Recall: To retrieve a saved temperature, simply short-press the corresponding channel button (CH1, CH2, CH3, or CH4).
3.2. System Settings
Short-press the "OK" button to enter the System Settings Menu. Use the arrow keys to navigate and "OK" to select. Long-press "OK" to exit.
- Display Mode: Select between Curve Mode (graphical temperature display) or Standard Mode (numerical temperature display).
- Language Settings: Choose your preferred language.
- Heating Channel: Switch between "Tweezers" and "Single" handle modes.
- Temperature Unit: Select between °C (Celsius) and °F (Fahrenheit).
- Temperature Calibration: Adjust temperature by ±99°C for calibration.
- Sleep Temperature: Set the sleep temperature range from 50°C to 200°C. Selecting "000" disables sleep temperature.
- Sound Settings: Turn sound ON or OFF.
- Key Lock: Enable or disable key lock.
- Key Doubling Speed: Adjust key press speed (1x, 5x, 10x).
- Brightness: Adjust display brightness from 010 to 100 (default is 50).
- Restore: Restore factory settings (YES/NO).
4. Maintenance and Upkeep
4.1. Soldering Iron Tip Care
- Temperature: Excessive temperature can weaken the function of the soldering iron tip. Always choose the lowest possible temperature for your task. The AIFEN-A99HD's excellent temperature recovery allows for effective soldering at lower temperatures, protecting sensitive components.
- Cleaning: Regularly use copper wire cleaning balls or copper brushes to clean the soldering iron tip. After welding, residual flux, oxides, and carbides can damage the tip, causing welding errors or reducing thermal conductivity.
- After Use: After each use, wipe the soldering iron tip clean and coat it with a new layer of tin to prevent oxidation.
4.2. Repair and Replacement
- Repairing Tips: Do not use a file to remove deposits from the soldering iron tip. Set the temperature to 250°C (482°F), clean the tip with a copper wire ball or brush, and then re-tin it. If the tip is deformed or heavily rusted, it must be replaced.
- Heating Element Replacement: This soldering station uses a heating element integrated with the soldering head. To replace, turn off the power, allow it to cool to room temperature, then remove the old heating element and insert the new one.
5. Troubleshooting
5.1. Error Messages
- "No Tools" Display: This message appears if the heating element of the soldering station is burnt out, broken, or not properly placed in the handle. The station will also emit an intermittent buzzing sound.
- "Short Circuit" Display: This message indicates that the heating element is burnt out and short-circuited. An uninterrupted buzzing sound will accompany this message. To resolve, remove the short-circuited heating element, turn off the host power, wait for 1 minute, and then restart the machine.
6. Specifications
| Feature | Specification |
|---|---|
| Input Voltage | AC100-240V 50/60Hz |
| Temperature Control Range | 100°C - 450°C (212°F - 842°F) |
| Peak Power (210 Handle) | 65W |
| Peak Power (245 Handle) | 180W |
| Peak Power (210 Tweezers Handle) | 120W |
| Peak Power (245 Tweezers Handle) | 320W |
| Dimensions (H x W x D) | 15cm x 14.5cm x 14.5cm |
| Weight | 0.93 KG |

7. User Tips
- The AIFEN-A99HD is significantly faster and cleaner for SMD component removal compared to using a single iron and wick.
- Utilize the four programmable buttons for quick and efficient temperature adjustments.
- Remember to set the correct heating channel (tweezers or single handle) in the menu before switching tools.
- The display offers strong contrast and a user-friendly interface, making it easy to read and operate.
- Ensure the soldering tips are at ground potential for safety and optimal performance.
8. Warranty and Support
For detailed warranty information and technical support, please refer to the official user manual PDF or contact the seller directly.
A comprehensive user manual is available for download: AIFEN-A99HD User Manual (PDF)