1. Introduction
This manual provides essential information for the safe and efficient installation, operation, and maintenance of the DOLD IL9079.12/003 Undervoltage Monitoring Relay. Please read this manual thoroughly before attempting to install or operate the device.
2. Safety Instructions
Always observe the following safety precautions:
- Installation and maintenance should only be performed by qualified personnel.
- Disconnect power before working on the device or its connections.
- Ensure proper grounding and wiring according to local and national electrical codes.
- Do not operate the device if it is damaged.
- The device is designed for industrial control applications. Use outside of specified parameters may result in damage or malfunction.
3. Setup and Installation
3.1 Unpacking and Inspection
Upon receiving the DOLD IL9079.12/003 relay, carefully unpack it and inspect for any signs of damage during transit. Verify that the model number and specifications match your order.
3.2 Mounting
The relay is designed for DIN rail mounting. Securely snap the device onto a standard 35mm DIN rail in a suitable control cabinet, ensuring adequate ventilation.
3.3 Wiring Connections
Refer to the wiring diagram and terminal labels on the device for correct connections. The relay monitors a 3-phase AC supply. Ensure all connections are tight and secure.

This image shows the top view of the DOLD IL9079.12/003 Relay. Input terminals L1, L2, L3 are for the 3-phase supply. Output contacts are labeled 11, 12, 14 (for one contact) and 21, 22, 24 (for a second contact). Two rotary potentiometers are visible for adjusting the undervoltage threshold (U) and the re-energization time delay (t).

The front view of the DOLD IL9079.12/003 Undervoltage Monitoring Relay displays key specifications: 3 AC 400V, 50/60Hz, undervoltage threshold (Uab) 0.55-1.05 UN, re-energization delay 0.2-2s, and output contact rating AC-15 230V 1A. The order number 0048057 and CE certification mark are also visible.
3.4 Setting Parameters
The relay features adjustable parameters for undervoltage threshold and re-energization delay:
- Undervoltage Threshold (U): Use the 'U' potentiometer to set the desired undervoltage detection level within the range of 0.55 to 1.05 times the nominal voltage (UN).
- Re-energization Delay (t): Use the 't' potentiometer to set the time delay for re-energization after the voltage returns to normal, adjustable from 0.2 to 2 seconds.
4. Operation
The DOLD IL9079.12/003 is an undervoltage monitoring relay designed to protect equipment from damage due to insufficient supply voltage in 3-phase AC systems.
- When the monitored 3-phase voltage falls below the set undervoltage threshold (U), the relay will de-energize its output contacts after a short response time.
- Once the voltage returns above the threshold, the relay will wait for the set re-energization delay (t) before re-energizing its output contacts. This delay prevents rapid cycling and protects connected loads.
- Status indicators (if present on the specific model variant) will provide visual feedback on the operational state and fault conditions.
5. Maintenance
The DOLD IL9079.12/003 relay is designed for long-term, maintenance-free operation under normal conditions. However, periodic checks are recommended:
- Visual Inspection: Regularly check for any signs of physical damage, discoloration, or loose connections.
- Cleaning: Keep the device free from dust and debris. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
- Functional Test: Periodically test the relay's function by simulating an undervoltage condition to ensure it operates correctly.
6. Troubleshooting
If the relay is not functioning as expected, consider the following:
- No Power/No Indication: Check the 3-phase supply voltage and ensure all input terminals (L1, L2, L3) are correctly wired and receiving power.
- Relay Not Tripping on Undervoltage: Verify the undervoltage threshold (U) setting. Ensure it is set appropriately for your application. Check the input voltage with a multimeter.
- Relay Not Re-energizing: Check if the voltage has returned above the threshold. Verify the re-energization delay (t) setting.
- Incorrect Output Behavior: Inspect the wiring of the output contacts (11, 12, 14 and 21, 22, 24) to ensure they are connected to the load as intended.
- Persistent Fault: If the issue persists after basic checks, consult a qualified electrician or contact DOLD technical support.
7. Specifications
| Model | IL9079.12/003 |
| Order Number | 0048057 |
| Brand | DOLD |
| Function | Undervoltage Monitoring Relay |
| Nominal Voltage | 3 AC 400V |
| Frequency | 50/60 Hz |
| Undervoltage Threshold (Uab) | 0.55 - 1.05 UN (Adjustable) |
| Re-energization Delay | 0.2 - 2 seconds (Adjustable) |
| Output Contacts | AC-15 230V 1A |
| Certification | CE |
| Origin | Mainland China (Manufacturing location) |
| Package Length | 30 cm |
| Package Width | 30 cm |
| Package Height | 30 cm |
| Package Weight | 1.5 kg |

This image shows the side view of the DOLD IL9079.12/003 Relay, featuring the product label with the DOLD brand logo, model number IL9079.12/003, order number 0048057, and manufacturing details including "Made in Germany".
8. User Tips
No specific user tips or frequently asked questions were available from provided reviews or Q&A content.
9. Warranty and Support
For warranty information and technical support, please refer to the official DOLD documentation or contact your authorized DOLD distributor. Ensure you have the model number (IL9079.12/003) and order number (0048057) available when seeking support.