FLIPSKY VX5

Contents

Flipsky VX5 IP68 Waterproof Remote Control User Manual

Model: VX5 | Brand: FLIPSKY

1. Introduction

The Flipsky VX5 is an advanced IP68 waterproof remote control designed for electric surfboards and electric skateboards. It features a high-resolution display, a powerful 5000mAh battery for extended use, and integrated high-precision positioning modules (Beidou, GPS, GNSS) for accurate speed measurement. Its ergonomic design ensures comfortable operation, while robust software features provide comprehensive control and data monitoring.

2. Package Contents

Upon unboxing your Flipsky VX5 remote control, please verify that all the following items are included:

Package contents of the VX5 remote, including the remote, manual, receiver, and accessories.
Figure 2.1: VX5 Remote Control Package Contents
  • Flipsky VX5 Remote Control
  • User Manual
  • Receiver Module
  • USB Magnetic Charging Cable
  • Lanyard/Float (typically yellow)
  • Various connection wires and connectors

3. Product Overview

3.1 Remote Control Layout

Labeled diagram of the VX5 remote control, highlighting its buttons and charging port.
Figure 3.1: VX5 Remote Control Button and Port Layout
  • Brake Trigger: Activates braking function.
  • Mode Button: Cycles through different operating modes.
  • Horn Button: Activates the horn (if connected and supported).
  • Setting Button: Accesses settings menu.
  • Power On/Off Trigger: Controls power to the device and acts as throttle.
  • USB Magnetic Charging Port: For charging the remote control.
  • 2 Inches Display Screen: High-resolution screen for real-time data display.

3.2 Display Screen Overview

The VX5 remote features a high-resolution 2-inch display that provides real-time operational data. The display content varies slightly between E-skateboard Mode and Surfing Mode.

Display screen icon introduction for E-skateboard Mode on the VX5 remote.
Figure 3.2: E-skateboard Mode Display Screen Icons

E-skateboard Mode Display Elements:

  • Number of GPS Positioning Satellites: Indicates GPS signal strength.
  • Time: Current time.
  • Remote Battery: Remote control battery level.
  • Eboard Working Mode: Current operating mode of the e-board.
  • Eboard Battery: Electric skateboard battery level.
  • Eboard Mode: Current mode (e.g., NORMAL).
  • Headlight: Headlight status (if connected).
  • Speed Gear: Current speed gear (High Speed: Red, Medium Speed: Yellow, Low Speed: Green).
  • Throttle Auto-locking Time: Time until throttle auto-locks.
  • Throttle Progress Bar: Visual representation of throttle input.
  • Working Record Time: Duration of current session.
  • Throttle Percentage: Numerical throttle input.
  • Realtime Speed: Current speed (e.g., Km/h).
  • Speed Unit: Unit of speed measurement.
  • TRIP: Distance traveled in current trip.
  • ESC.POWER: Power consumption of the ESC.
  • MOS.TEMP: MOSFET temperature.
  • ODO: Odometer (total distance traveled).
  • BAT.Voltage: Battery voltage.
  • MOT.TEMP: Motor temperature.
  • BAT.Current: Battery current.
  • MOT.Current: Motor current.
  • Duty: Motor duty cycle.
Display screen icon introduction for Surfing Mode on the VX5 remote.
Figure 3.3: Surfing Mode Display Screen Icons

Surfing Mode Display Elements:

  • Number of GPS Positioning Satellites: Indicates GPS signal strength.
  • Time: Current time.
  • Remote Battery: Remote control battery level.
  • Receiver signal quality: Strength of the signal from the receiver.
  • Surfboard Battery: Surfboard battery level.
  • Surfing Mode: Current surfing mode.
  • Speed Gear: Current speed gear.
  • Throttle Auto-locking Time: Time until throttle auto-locks.
  • Throttle Progress Bar: Visual representation of throttle input.
  • Working Record Time: Duration of current session.
  • Throttle Percentage: Numerical throttle input.
  • Realtime Speed: Current speed (e.g., Km/h).
  • Speed Unit: Unit of speed measurement.
  • TRIP: Distance traveled in current trip.
  • ESC.POWER: Power consumption of the ESC.
  • MOS.TEMP: MOSFET temperature.
  • ODO: Odometer (total distance traveled).
  • BAT.Voltage: Battery voltage.
  • MOT.TEMP: Motor temperature.
  • BAT.Current: Battery current.
  • MOT.Current: Motor current.
  • Duty: Motor duty cycle.

4. Specifications

FeatureSpecification
ModelVX5
Waterproof RatingIP68
Battery Capacity5000mAh
Continuous Use TimeUp to 20 hours
Display Screen Size2 inches (High Resolution)
Positioning ModulesIntegrated Beidou, GPS, GNSS
Supported ESC ProtocolsVESC, FTESC, FOCBOX, PPM
Dimensions (Approx.)188mm (Height) x 146.4mm (Length) x 67.5mm (Width)
Weight (Approx.)0.8 kg
Charging PortUSB Magnetic
Additional FeaturesHigh-precision battery meter, high-precision encoder chip, M6 nuts for accessories, internal large cavity for buoyancy.
Dimensions of the VX5 remote control (188mm, 146.4mm, 67.5mm).
Figure 4.1: VX5 Remote Control Dimensions

5. Setup

5.1 Initial Charging

Before first use, fully charge the VX5 remote control using the provided USB magnetic charging cable. Connect the magnetic end to the charging port on the remote and the USB-A end to a compatible USB power source (e.g., computer, wall adapter). The display will indicate charging status.

5.2 Receiver Wiring

The VX5 remote control supports various ESC protocols including VESC, FTESC, FOCBOX, and PPM. Ensure your receiver is correctly wired to your Electronic Speed Controller (ESC) based on the desired control mode.

Wiring diagram for PPM control mode and PPM dual channel connection mode for the VX5 receiver.
Figure 5.1: Receiver Wiring Diagrams

PPM Control Mode (Single Channel)

This mode is applicable to all ESCs without forward and reverse switching functions. Connect the receiver to the ESC as follows:

  • BAT+: Connect to battery positive.
  • VRX2, VTX2, VRX1, VTX1: These pins are typically for auxiliary functions or not used in basic PPM mode. Refer to your ESC manual for specific connections.
  • GND: Connect to ground.
  • 5V: Connect to 5V power supply from ESC.
  • PPM: Connect to the PPM input on your ESC.

PPM Dual Channel Connection Mode

This mode is also applicable to all ESCs without forward and reverse switching functions, typically used for dual motor setups or specific control requirements. Connect the receiver to the ESCs as follows:

  • BAT+: Connect to battery positive.
  • VRX2, VTX2, VRX1, VTX1: Auxiliary functions, refer to ESC manual.
  • GND: Connect to ground.
  • 5V: Connect to 5V power supply from ESC.
  • PPM1: Connect to the PPM input of ESC1.
  • PPM2: Connect to the PPM input of ESC2.

Note: Always refer to your specific ESC's instruction manual for detailed wiring and configuration to ensure proper and safe operation.

5.3 Pairing the Remote and Receiver

While specific pairing instructions are not detailed, typically, you will need to:

  1. Ensure both the remote and receiver are powered on.
  2. Press and hold the pairing button on the receiver (if present) until an indicator light flashes.
  3. Initiate pairing mode on the VX5 remote via the 'Setting Button' and navigating to the pairing option.
  4. Once paired, the indicator lights on both devices should show a solid connection.

6. Operating Instructions

6.1 Power On/Off

Press and hold the Power On/Off Trigger to turn the remote control on or off.

6.2 Throttle Control

The VX5 features a high-precision encoder chip for precise throttle control. The Power On/Off Trigger also functions as the throttle. Gently press or release to control acceleration and deceleration.

6.3 Mode Selection

Use the Mode Button to cycle through different operating modes. The available modes and their functionalities will be displayed on the 2-inch screen. For FTESC ESCs, a new one-key mode switching feature allows toggling between:

  • Normal Mode
  • Tank Turnaround Mode
  • Hill Climbing Cross-Country Mode
  • Traction Control Mode

6.4 Speed Gears and Throttle Percentage

  • The remote supports L (Low), M (Medium), and H (High) gears for different throttle percentage settings. Adjust these settings via the Setting Button menu.
  • In surfboard mode, the remote supports up to 20 different gears for fine-tuned control.

6.5 Display Interpretation

Refer to Figures 3.2 and 3.3 in the Product Overview section for a detailed explanation of the icons and data displayed on the screen for both E-skateboard and Surfing modes. Pay attention to real-time speed, battery levels (remote and board), motor/MOSFET temperatures, and current draw to ensure safe operation.

6.6 Settings and Customization

Press the Setting Button to access the remote's menu. Here you can:

  • Adjust throttle curve presets.
  • Set throttle response time presets.
  • Configure various remote control throttle auto-lock modes.
  • Change language settings (Chinese, English, Russian supported).
  • View riding data records (up to 11 records).
  • Check ESC fault alarm codes (stores up to 20 codes).
  • Perform GPS automatic time calibration.

7. Maintenance

7.1 Charging

Regularly charge the 5000mAh battery using the USB magnetic charging cable. A full charge provides up to 20 hours of continuous use. Avoid overcharging or completely draining the battery for optimal lifespan.

7.2 Cleaning and Waterproofing

The VX5 remote has an IP68 waterproof rating, making it resistant to dust and immersion in water. After use in saltwater environments, it is recommended to rinse the remote with fresh water and dry it thoroughly to prevent salt buildup and corrosion.

7.3 Storage

Store the remote control in a cool, dry place away from direct sunlight and extreme temperatures. If storing for an extended period, ensure the battery is charged to approximately 50-60%.

7.4 Firmware Updates

The remote supports online firmware upgrades. Periodically check the manufacturer's website or app for available updates to ensure optimal performance and access to new features. Follow the provided instructions carefully during the update process.

8. Troubleshooting

8.1 Common Issues

ProblemPossible CauseSolution
Remote not powering onLow batteryCharge the remote control fully.
No connection to boardNot paired, receiver off, out of rangeEnsure receiver is powered on and paired. Check range.
Inaccurate speed readingPoor GPS signalEnsure clear line of sight to sky for GPS.
Display not workingSoftware glitch, hardware issueTry restarting the remote. If issue persists, contact support.

8.2 ESC Fault Alarm Codes

The VX5 remote can store up to 20 ESC fault alarm codes. If you experience issues with your electric board, navigate to the fault code log in the remote's settings menu. These codes can help diagnose problems with your ESC. Refer to your ESC's manual for the meaning of specific fault codes.

9. User Tips

  • Buoyancy Feature: The internal large cavity design allows the remote to float even without a buoyancy rope. This is a significant safety feature to prevent loss in water.
  • Accessory Attachment: Utilize the built-in M6 nuts on the bottom of the remote to easily attach accessories such as flashlights or cameras, enhancing your riding experience.
  • Ergonomic Comfort: The compact and ergonomically designed structure helps reduce fatigue during prolonged use, making it comfortable for long sessions on your electric surfboard or skateboard.
  • Regular Data Review: Periodically check the riding data records and ESC fault alarm codes to monitor performance and proactively address any potential issues.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the manufacturer or your point of purchase. Keep your proof of purchase for any warranty claims.

© 2023 FLIPSKY. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.