WIFI Tuya HORMANN Smart RF Bridge Intelligent Garage Door Opener User Manual

1. Introduction

This Scimagic-RC Smart RF Bridge combines RF and TUYA mobile app control to provide intelligent control over your garage door or gate. Once paired with your network, you can remotely control your gate via the Tuya mobile app. The device also supports voice control through smart speakers like Alexa and Google Assistant, and allows for control sharing with other users. This smart device simplifies traditional complicated receiver wiring, offering a convenient, quick, and secure solution for gate automation.

Figure 1: Scimagic-RC Smart RF Bridge, compatible with major smart home platforms.

2. Key Features

• APP Remote Control: Control your garage door or gate from anywhere, anytime, using the Tuya Smart or Smart Life app.
• RF Control: Functions as an RF remote to directly control your garage door or gate.
• Voice Control: Integrate with Amazon Alexa and Google Assistant for hands-free operation.
• Easy Installation: No complicated wiring required after powering up the device, enabling quick mobile phone control.
• Share Function: Easily share control of your garage door with family and friends, with the option to revoke access.

Figure 2: Overview of control methods: RF, App, and Voice.

3. Compatibility

This device is compatible with the following 868MHz remote controls (blue button series):

• Hormann: hsm2 868, hsm4 868, hs1 868, hs2 868, hs4 868, hse2 868, hse4 868, hsz1 868, hsz2 868, hsp4 868, hsp4-c 868, hsd2-A 868, hsd2-c 868 (Hormann blue button 868mhz)
• Marantec: Digital D382 868, Digital D384 868, Digital D302 868, Digital D304 868, Digital D313 868, Digital D321 868, Digital D323 868, Command 131 868

Note: This device is NOT compatible with Hormann BS series remotes or any other models not listed above.

Figure 3: Compatible and incompatible remote control types.

4. Setup and Pairing

4.1 Powering On

Connect the device to a power source using a USB Type-C 5V cable.

Figure 4: USB Type-C 5V power input.

4.2 Clear Replicator History Code

Before copying a new remote, it is essential to clear any existing codes from the device.

1. Press and hold buttons 3 and 4 simultaneously until the LED flashes 3 times.
2. Release button 4 (continue to press button 3), then slowly press button 4 three times while the LED blinks.
3. Release button 3 to complete the code erasure.

4.3 Copying Code from Original Transmitter

To duplicate an existing remote control:

1. Place the duplicator (Smart RF Bridge) next to the original transmitter, as close as possible.
2. Press and hold the desired button (1, 2, 3, or 4) on the original transmitter. Simultaneously, press and hold the corresponding button on the duplicator until you see the duplicator's LED blink.
3. Release both buttons to complete the code duplication. Repeat for other buttons as needed.

4.4 Programming without Original Remote (Directly on Receiver)

If you do not have the original remote control, you can program the device directly to your gate receiver:

1. Open the casing of your gate receiver, typically located next to your motor.
2. On the receiver circuit board, press and release the programming button (labeled ENR, MEMO, PROG, or REC, depending on the model). The LED light on the receiver should illuminate or blink.
3. Press a button on your new Smart RF Bridge for 1 second.
4. Release the button. The LED light on the receiver should turn off immediately or within 10 seconds, indicating successful programming.

After completing one of the above programming steps (4.3 or 4.4), you can proceed to connect your mobile phone to the device.

5. Mobile App Connection

5.1 Checklist Before Using the Device

• Your smartphone or tablet must be connected to a 2.4GHz WiFi network with internet access.
• Ensure Bluetooth is enabled on your phone.
• Have the correct WiFi password readily available.
• Your smartphone or tablet must have access to an app store (e.g., Google Play).
• Your router should be MAC-open (if applicable for your network setup).

5.2 User Guide (App Pairing)

1. Download the "Tuya Smart" or "Smart Life" app from your mobile app store or by scanning the QR code below.
2. Register for a Tuya Smart account or log in if you already have one.
3. Start Pairing:
   • If the network indicator (red light) on the device is already blinking fast (0.5 seconds/time), skip the reset step.
   • Otherwise, power on the device, then hold down the Reset button (Distribution Key) for 10 seconds until the network indicator (red light) blinks fast (0.5 seconds/time).
4. In the Tuya Smart app, click the "+" icon in the top right corner, then select "Auto scan". Wait a few seconds for the device to be found, then click "Next".
5. Select your 2.4GHz Wi-Fi network and enter your password.
6. Name your device.
7. You can now start controlling your device with your mobile phone.

Figure 5: Scan to download the Tuya Smart app.

Figure 6: Tuya Smart app interface for adding and controlling the device.

6. Operating the Device

6.1 RF Control

Once programmed, use the physical buttons on the Smart RF Bridge to control your garage door or gate, similar to an original remote control.

Figure 7: Using the physical buttons for RF control.

6.2 App Control

Open the Tuya Smart or Smart Life app on your smartphone or tablet. From the device interface, you can tap the virtual buttons to open or close your garage door/gate remotely.

Figure 8: Remote control of garage door via mobile app.

6.3 Voice Control

After linking your Tuya Smart account with Amazon Alexa or Google Assistant, you can use voice commands to operate your garage door or gate. For example, "Alexa, open the garage door."

Figure 9: Voice control functionality with smart speakers.

6.4 Share Function

The Tuya Smart app allows you to share control of the Smart RF Bridge with other family members or trusted individuals. You can also manage and remove shared access as needed.

Figure 10: Sharing control of the device with multiple users.

7. Troubleshooting

• Device not pairing with original remote: Ensure the Smart RF Bridge is placed as close as possible to the original remote during the copying process. Verify that the original remote is functioning correctly. Double-check the button press sequence for clearing and copying codes.
• LED not blinking as expected during setup: Refer to the "Clear Replicator History Code" and "User Guide (App Pairing)" sections. Ensure you are holding the correct buttons for the specified duration.
• App connection issues: Confirm your smartphone is connected to a 2.4GHz WiFi network, not 5GHz. Ensure Bluetooth is enabled on your phone. Verify the WiFi password is correct. If the device was previously paired, try resetting it by holding the Reset button for 10 seconds until the network indicator blinks fast.
• Programming button 1 not activating: If you encounter issues with a specific button not programming (e.g., Hormann HS4 button 1), ensure you are following the exact steps for clearing and copying codes. Sometimes, a factory reset of the Smart RF Bridge followed by a fresh programming attempt can resolve this.

8. Specifications

9. User Tips

• Precise Button Sequence: When clearing and copying codes, ensure you follow the button press sequence precisely. Any deviation can lead to programming failure.
• Receiver Programming: If programming directly to the receiver, confirm that the receiver's programming button is correctly activated (LED blinking/illuminated) before attempting to pair the new remote.
• WiFi Band: Always ensure your phone and the device are connected to a 2.4GHz WiFi network during the app pairing process, as 5GHz networks are not supported.

10. Warranty and Support

All products purchased from our store come with a 1-year warranty. For any technical assistance, troubleshooting, or warranty claims, please contact the seller directly through the platform where you made your purchase.

For additional guides and documents, you may refer to the User Manual (PDF).