CNCEST Magnetic Induction Heater Kit

Contents

CNCEST 220V 1100W Magnetic Induction Heater Kit Instruction Manual

Flameless Heat Induction Tool for Screw Removing

1. Introduction

The CNCEST Magnetic Induction Heater Kit is a powerful and efficient tool designed for flameless heating of metal parts, primarily for removing rusted or seized bolts and nuts. Utilizing high-frequency magnetic fields and electromagnetic induction, this handheld device provides rapid and localized heat without the need for open flames or water cooling, ensuring a safer and more convenient operation. This manual provides essential information for the safe and effective use of your induction heater.

2. Safety Instructions

Please read and understand all safety instructions before operating this product. Failure to follow these instructions may result in electric shock, fire, or serious injury.

  • Professional Use Only: This device is intended for professional use.
  • Eye Protection: Do not look directly into the LED lamp during operation.
  • Unplug When Not In Use: Always unplug the unit from the power source when not in use or before performing any maintenance.
  • Material Compatibility: This product is only suitable for heating steel and iron items. Do not use on other materials.
  • Overheat Protection: The heater is equipped with a safety mechanism that stops heating if the temperature reaches 140℉ (60℃). Allow the unit to cool down naturally before resuming operation to prevent damage or injury.
  • Power Cord Integrity: Ensure the power cord plug is secure and in good contact to prevent poor contact damages to the device.
  • Ventilation: Ensure adequate ventilation around the device during operation to facilitate heat dissipation.
Close-up of the induction heater's warning labels and power button

Figure 1: Warning labels and power button on the induction heater.

3. Product Overview

3.1 Package Contents

Your CNCEST Magnetic Induction Heater Kit includes the following items:

  • 1x Magnetic Induction Heater Unit
  • 8x Heating Coils (various sizes)
  • 2x English User Manuals
Full kit including the heater, various coils, and user manuals

Figure 2: Complete contents of the Magnetic Induction Heater Kit.

3.2 Specifications

FeatureSpecification
ColorBlue
Coil MaterialCopper, Glass Fibre
Product MaterialPlastic, Aluminum, Copper
ProcessInjection Molding
Power SourcePower Corded
Plug TypeEU Standard
Voltage220V
Power Cord Length1.6m / 5.25ft
Heating Time5-40s (Depending on the Workpiece)
Power1100W
Rated Current9A
Coil Output Voltage/Current18V / 50A
Maximum Heating Temperature800℃ / 1472℉
Number of Heating Coils8
Coil Inner Diameter30mm/1.18inch, 40mm/1.57inch, 50mm/1.97inch
Soft Coil Length750mm / 29.53inch
Product Size (D*L)6.5*40cm / 2.56*15.75inch
Gross Weight1.6kg / 3.53lbs
Net Weight1.3kg / 2.87lbs
Diagram showing the dimensions of the induction heater

Figure 3: Product dimensions of the induction heater.

Close-up of the EU standard power plug

Figure 4: EU standard power plug.

4. Setup

Follow these steps to prepare your induction heater for operation:

  1. Select the Appropriate Coil: Choose a heating coil that best fits the size and shape of the workpiece you intend to heat. The kit includes coils with inner diameters of 30mm, 40mm, and 50mm, as well as soft coils for custom shapes.
  2. Insert the Coil: Carefully insert the ends of the chosen heating coil into the two sockets at the front of the heater unit.
  3. Lock the Coil: Rotate the front part of the heater (the red section) to lock the coil securely in place. Ensure it is firmly seated to prevent poor contact.
  4. Connect to Power: Plug the EU standard power cord into a compatible 220V power outlet. The power cord length is 1.6m (5.25ft).
Close-up of the coil insertion and locking mechanism

Figure 5: Coil insertion and locking mechanism.

Diagram illustrating simple operation steps: coil insertion, lock, press button

Figure 6: Simple operation steps for the induction heater.

5. Operating Instructions

Once the heater is set up, follow these steps to operate it:

  1. Position the Coil: Place the heating coil around the metal part you wish to heat (e.g., a rusted bolt or nut). Ensure the coil is as close as possible to the workpiece without touching it directly, allowing for optimal induction.
  2. Activate Heating: Press the red power button located on the handle of the induction heater. The device will begin to generate a high-frequency magnetic field, rapidly heating the metal workpiece.
  3. Monitor Heating: The heating time typically ranges from 5 to 40 seconds, depending on the size and type of the workpiece. Observe the workpiece for signs of heating (e.g., glowing red).
  4. Deactivate Heating: Release the red power button to stop the heating process.
  5. Remove Workpiece: Once sufficiently heated, carefully remove the bolt or nut using appropriate tools. Be aware that the workpiece will be extremely hot.
  6. Cool Down: Allow the heater unit to cool down naturally after use. If the internal temperature reaches 140℉, the unit will automatically shut off and require cooling before it can be restarted.
Induction heater in use on a large rusty bolt

Figure 7: Heating a large rusty bolt with the induction heater.

Induction heater in use on a car suspension bolt

Figure 8: Heating a bolt on a car suspension component.

Induction heater in use on a rusty brake rotor bolt

Figure 9: Heating a rusty bolt on a brake rotor.

6. Maintenance

Proper maintenance ensures the longevity and optimal performance of your induction heater.

  • Cleaning: After each use, ensure the unit is unplugged and cooled. Wipe down the exterior with a clean, dry cloth. Do not use abrasive cleaners or immerse the unit in water.
  • Ventilation: Keep the cooling fan and heat emission holes clear of dust and debris to ensure efficient heat dissipation. Blocked vents can lead to overheating and reduced service life.
  • Coil Inspection: Regularly inspect the heating coils for any signs of damage or wear. Replace damaged coils immediately to maintain performance and safety.
  • Storage: Store the induction heater and its coils in a dry, clean place away from direct sunlight and extreme temperatures. Unplug the unit when not in use.

7. Troubleshooting

If you encounter issues with your induction heater, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Heater does not turn onNo power supply; Loose power cord connection; Unit overheated and shut off.Check power outlet; Ensure power cord is securely plugged in; Allow unit to cool down naturally if it was recently used.
Workpiece not heating effectivelyIncorrect coil size; Coil not properly inserted/locked; Workpiece material is not steel or iron.Select a coil that closely fits the workpiece; Ensure coil is securely locked; Confirm workpiece is made of steel or iron.
Unit stops heating during operationOverheat protection activated.Release the power button and allow the unit to cool down naturally before resuming. Ensure ventilation is not obstructed.

8. User Tips

Maximize your experience with these helpful tips:

  • Choose the Right Coil: Using a coil that closely matches the size of the bolt or nut will concentrate the heat more effectively and speed up the removal process. For irregularly shaped parts, the soft coil can be bent to fit.
  • Pre-clean Workpiece: For heavily rusted parts, a quick wire brushing can help improve heat transfer and visibility.
  • Safety First: Always wear appropriate personal protective equipment, including heat-resistant gloves and eye protection, when operating the induction heater.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your seller or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.