BRDCLIP Professional Hair Clipper, Trimmer, and Shaver User Manual

1. Important Security Warnings

1.1 Professional Use Safety

• Only professional operators who have received training are allowed to use these devices. Read this manual carefully and master the operation specifications before use.
• Children under 8 years of age are prohibited from access to the devices. Work areas must be equipped with child isolation measures; minors are not allowed to operate alone.
• Do not touch the moving parts of the blade during operation to avoid injury. Before replacing any blade, power off the device and wait for the blade to stop completely.
• Only the product's original EU-certified professional-grade charging cable and adapter (compatible with 110V-240V wide voltage range) are permitted. The use of any non-original charging accessories is strictly prohibited.
• This product is not waterproof. Do not use it in the bathroom, shower room, or other humid environments. Avoid water contact with the body and charging interface to prevent short circuit or electric shock.
• For continuous operation not exceeding 2 hours, a 10-minute cooling shutdown is required to prevent brushless motor overheating and damage, in compliance with the EN 60335-2-23 continuous operation standard.
• These products are intended for hair trimming only. Do not use them to trim beards, armpit hair, or other body parts. They are also not suitable for pet grooming.

1.2 Electrical Safety (Enhanced for Commercial Use)

• The devices comply with the Low Voltage Directive (2014/35/EU) and professional electrical safety standards, featuring a rated voltage of 110V-240V (globally compatible wide voltage range) and Class II insulation rating.
• Commercial premises must comply with the EU EN 50075 standard for wiring, with proper grounding. Extension cables must be professional-grade waterproof (IP44 or higher) and compatible with wide voltage requirements.
• Before daily use, inspect the charging cable, charging pad, and device for damage. If cracks or electrical leakage are detected, stop using it immediately and contact the authorized service center for repairs.
• Always unplug the charger before cleaning or replacing parts.
• If a device is idle for more than 4 hours, turn off the power. If it is not used for more than 15 days, remove the charging pad and store it in a dry, well-ventilated environment.

2. Product Overview & Specifications

The BRDCLIP set includes professional hair clippers (BRD-106B, BRD-116) and a shaver (BRD-609), designed for commercial use in barbershops and salons. Below are the detailed specifications for each model and their accessories.

Figure 1: BRDCLIP 106B, 116, and 609 models

2.1 Technical Parameters

Figure 2: Battery and charging details for BRD-116, BRD-106B, and BRD-609

Figure 3: LCD display and switch buttons for BRDCLIP devices

Figure 4: Blade details for BRD-106B, BRD-116, and BRD-609

Figure 5: Removable parts and magnetic covers

Figure 6: Motor speed details for BRDCLIP devices

2.2 Professional Packaging List

The following items are typically included in the BRDCLIP product packages. Specific contents may vary by set (e.g., W-106B-116, W106B-116-609, W106B-116-609 Bld, W-106B-116 Bld).

• Professional hair clippers (BRD-106B, BRD-116)
• BRD-609 high-speed shaver
• Professional charging cable(s) (USB Type-C and/or Figure 8 dual interface, EU CE certified, supports wide voltage)
• Professional charging dock(s) (with overcharge protection, compatible with 110V-240V)
• Precision limit comb sets (e.g., 8 combs for 1.5/3/4.5/6/9/12/16/19mm, or 4 combs for 1.5/3/4.5/6mm, and 3 trim restricted combs)
• Professional cleaning brush(es) (high-density bristles)
• Blade head protection cover(s)
• Golden knife (for 'Bld' sets)
• Original 116 blade (for 'Bld' sets)
• English professional user manual

Figure 7: Accessories for W-106B-116 set

Figure 8: Accessories for W106B-116-609 set

Figure 9: Accessories for W106B-116-609 Bld set

Figure 10: Accessories for W-106B-116 Bld set

3. Setup & Charging Operation

3.1 Charge Operation (Optimized for Commercial Scenarios)

1. Ensure the charging dock and cable match the product specifications. Connect the cable to the dock, then plug the dock into a standard EU commercial outlet (110V-240V).
2. Place the hair clipper/trimmer firmly on the charging dock, ensuring the charging port is fully engaged (the circular LED indicator lights up red, indicating charging).
3. The LED indicator stays red during charging and turns green when fully charged. Charging times vary by model: BRD-106B and BRD-609 take approximately 2.5 hours, while BRD-116 takes approximately 3 hours.
4. Remove the device immediately after full charging and disconnect the charging dock to prevent overheating from prolonged use in commercial settings. Each charge should not exceed 4 hours.
5. For business scenarios, it is recommended to install backup charging ports to enable multiple devices to be charged in rotation, ensuring uninterrupted operation.

4. Professional Operation Steps

1. Blade Installation: Align the blade with the screw hole and tighten the screw to secure it in place. Before installation, ensure the blade is free of debris and may be lightly lubricated with a small amount of specialized lubricant (to be purchased separately).
2. Limiting Comb Selection: Choose the appropriate comb setting (e.g., 1.5mm-19mm for clippers) based on your hairdressing needs. Secure the blade head with a snap-fit mechanism to ensure a tight installation. For professional use, check the installation tightness before each use.
3. Power-on Procedure: Press the power button for 1 second (the blue LED indicator will remain on, the device will start, and the blade will rotate at its specified RPM).
4. Professional Hairdressing Tips:
   • For thick hair: Work against the natural growth direction at a 45° angle, using high-speed rotation to cut quickly and avoid pulling the strands by pressing too hard.
   • Fine trimming: Use a 1.5mm/3mm limit comb and gently move it along the hair growth direction, keeping the blade parallel to the skin, and adjust the trimming range in small increments.
   • Contouring: Remove the limit comb and use the 1.5mm setting. With the blade perpendicular to the hair direction, precisely trim the hairline and contour lines.
5. Shut-down Procedure: Press the power button for 1 second (the LED circular indicator will turn off). After continuous operation for 2 hours, the device will automatically power off (overheat protection). Reboot after cooling for 10 minutes.

5. Maintenance & Cleaning

5.1 General Cleaning and Disinfection Notes (Non-Waterproof Professional Edition)

• Do not wash: These products are not waterproof. Do not immerse the body or blade in water or rinse with running water to prevent water from entering and causing motor short circuit.
• Professional cleaning: After use, remove hair fragments from the blade tip and body gaps with the included cleaning brush (focus on the blade engagement area), then wipe the body surface with a dry soft cloth.
• Professional disinfection: Gently wipe the blade surface with alcohol swabs (after turning off the power and ensuring the device is cooled). Wait for the alcohol to fully evaporate before use. Avoid alcohol contact with the plastic components and charging ports of the device.
• Important note: Keep the equipment dry throughout cleaning and disinfection. If it comes into contact with water, immediately disconnect the power, dry it with a towel, and let it air-dry completely before reusing.

5.2 Daily Cleaning (After Each Use)

1. Shut down and disconnect the power supply, then remove the limit comb.
2. Use a professional cleaning brush to thoroughly remove hair fragments from the blade's engagement area and device gaps, ensuring complete clearance (immediate cleaning after each service is recommended in commercial settings).
3. Wipe the fuselage surface and limit comb with a dry soft cloth to remove dust and hair debris.
4. (Optional) Drop 1 drop of special lubricating oil (to be purchased separately) to the blade head, run the machine for 10 seconds, and make the lubricating oil evenly distributed to improve the wear resistance of the blade head.
5. The cleaned limit comb should be reinstalled or stored with the hair trimmer in a dry storage space to avoid dampness.

5.3 Deep Maintenance (Once a Week)

1. After completing the basic cleaning as per daily procedures, inspect the blade for wear. If you notice chipped edges, diamond-like carbon coating detachment, or poor shearing performance, contact customer service immediately to replace with a factory-certified EU-compliant blade.
2. Check the charging dock and cable: Clean the charging port to ensure good contact; inspect the cable for damage or wear, and replace it if needed.
3. Battery status check: After fully charging the device, run it continuously for 30 minutes and check the LED indicator. If there is a sudden power outage or a significant drop in battery life (below 180 minutes), contact customer service to have the battery checked.
4. For maintenance: Wipe the device body with a dry cloth dipped in a small amount of specialized plastic cleaner (containing alcohol or corrosive components is prohibited) to maintain the ABS material's luster and stain resistance.

5.4 Blade Replacement (Professional)

1. Business scenarios recommend replacing the blade head every 6 months (or when the usage time reaches 1000 hours) to ensure cutting performance and hygiene standards.
2. Replacement procedure:
   1. Disconnect power supply.
   2. Gently pull the blade head outward with both hands.
   3. Insert the new blade head into the slot with a click.
   4. Check for looseness.
   5. (Optional) Apply lubricant.
   6. Start trial run (If no abnormal noise and smooth cutting, it's ready for use).
3. Only BRDCLIP's original EU-compliant M390 steel blade is approved. Using non-original blades may cause equipment malfunctions, compromised cutting performance, and safety hazards.

6. Troubleshooting (Common Issues in Business Settings)

7. User Tips

• Regular Oiling: Apply a small amount of lubricating oil to the blades before and after each use to ensure smooth operation and prolong blade life.
• Full Charge for Best Performance: Always ensure your device is fully charged before a grooming session to maintain consistent power and prevent unexpected shutdowns.
• Clean After Every Use: Promptly clean hair clippings from the blades and body after each use to prevent buildup and maintain hygiene and cutting efficiency.
• Store Properly: Keep the devices and accessories in a dry, clean place away from humidity to prevent damage.

8. Warranty & Support

8.1 EU Business Warranty Policy

In accordance with the EU Consumer Rights Directive (2011/83/EU) and the warranty standards for commercial products, this product is covered by a 2-year commercial warranty from the date of purchase.

Warranty Scope: Material or manufacturing defects in core components such as motors, batteries, and charging bases; malfunctions caused by normal use in commercial scenarios (as specified in this manual).

Not Covered:

• Normal wear of the blade tip (3-month warranty provided).
• Misuse, collision, unauthorized modification, failure to maintain as instructed, or damage caused by water ingress.
• Equipment repaired by non-EU authorized service centers.
• Non-original accessories not included in the packaging list (such as self-purchased lubricants, cleaning products, etc.).

8.2 Business Customer Exclusive Service

• EU Customer Service Hotline: [24-hour service number, dedicated email for business users]
• EU Authorized Professional Repair Centers: [Commercial repair service locations and contact details across EU member states, covering key countries including Germany, France, the UK, Italy, and Spain]
• Home service: Commercial users can enjoy free home repair service for 1 year after purchase (limited to major cities in the EU).
• Backup device support: If the repair period exceeds 3 days, you can apply for a free backup hairdressing device (you need to provide proof of business operation).
• Official Website (Business User Zone): [BRDCLIP EU Official Website Business User Portal, offering instruction manual downloads, accessory orders, maintenance guides, and other services]

9. Recycling and Disposal Instructions (Professional Edition)

9.1 RoHS Compliance Statement

All components of this product (including ABS body, M390 steel blade, lithium-ion battery, etc.) comply with the requirements of RoHS Directive 2011/65/EU and its amendments, with the content of hazardous substances strictly controlled within the permissible limits:

• Lead (Pb) ≤ 0.1% | Mercury (Hg) ≤ 0.1% | Cadmium (Cd) ≤ 0.01%
• Cr (VI) ≤ 0.1% | PBBs ≤ 0.1%
• PBDEs ≤ 0.1% | phthalates ≤ 0.1%

9.2 WEEE Recycling and Commercial Waste Disposal

• This product is classified as a Commercial Waste Electrical and Electronic Equipment (WEEE). Commercial users must hand over the discarded equipment to EU-designated WEEE recycling organizations (marked with the WEEE commercial recycling label) and must not mix it with regular commercial waste for disposal.
• Battery Disposal: The battery should be fully discharged before disposal, the charging interface should be wrapped with insulating tape, and the battery should be sent to the EU commercial battery recycling point ("Li-ion Professional Battery-BRD-108").
• Blade Head Treatment: Waste blade heads should be sealed in a special protective box (to avoid scratching the recovery personnel) and handed over to a metal recycling agency or BRDCLIP authorized recycling point to ensure compliance with EU environmental standards.
• Overall Equipment Treatment: Contact the authorized WEEE commercial recycling agency of the European Union (which can be checked through the official website of BRDCLIP), provide the product model and purchase certificate, and the professional agency will collect the product on-site or send it to the designated recycling center. Private disassembly is prohibited.
• Recovery Certificate: Please request a recovery certificate (in compliance with the EU WEEE Directive traceability requirements) after recovery for commercial compliance inspection and environmental audit.

This manual is the BRDCLIP Professional Commercial Edition, exclusively for commercial use within the EU. Product specifications and instructions are subject to the actual product. Any updates will be published on the BRDCLIP EU official website's Commercial User Zone without prior notice.

Copyright © BRDCLIP. All rights reserved. Unauthorized reproduction or dissemination of any content in this manual is prohibited.