1. Introduction
The TELESIN Underwater Diving Phone Case is designed to protect your smartphone and enable photo and video capture during underwater activities such as snorkeling and diving. With an IP68 waterproof rating, it allows for safe operation up to 20 meters (65 feet) deep. The integrated Bluetooth remote control provides convenient one-finger operation for various camera functions.

2. Package Contents
Please check the box for the following items:
- Diving Handle × 1
- Vacuum Pump × 1
- USB Charging Cable × 1
- Safety Hand Strap × 1
- Mirror Cloth × 1
- Instruction Manual × 1

3. Specifications
| Feature | Detail |
|---|---|
| Material | ABS/PC/Aluminum alloy |
| Product Dimensions | 20.37 x 10.92 x 5.2 cm (8.01 x 4.29 x 2.04 inches) |
| Product Weight | 397 g (14 oz) |
| Waterproof Level | IP68, up to 20 meters (65 feet) underwater |
| Compatibility (Phone Size) | iPhone 12-16 series, Samsung S20-S25 series, and most 5.4-6.9 inch smartphones |
| Adapter | Bluetooth adaptation: iOS, Android |
| Expansion Interface | Universal 1/4 threaded hole × 2 |
| Features | Water-Resistant, Full Coverage, Transparent Design |

4. Setup Guide
4.1 Watertight Safety Test (Before First Use)
Before using the case with your phone, it is crucial to perform a watertight safety test to ensure no water ingress. This test should be done without your phone inside.
- Place a tissue inside the case.
- Seal both the case and the vacuum cover securely.
- Fully submerge the case in water for 30+ minutes.
- Do not open immediately after retrieval.
- Check if the tissue remains dry.
- If dry: Waterproof verified.
- If wet: Contact customer service.
4.2 Bluetooth Connection
To enable remote control functions, connect the diving handle to your phone via Bluetooth.
- Power on the diving handle (long press the Capture Button).
- On your phone, go to Bluetooth settings and connect to "TELESIN SDC".
*Note: If not connected within 2 minutes, the device will automatically power off.
4.3 iOS Initial Setup (One-Time Only)
For iPhone users, a one-time setup is required to unlock full feature compatibility:
- Go to Settings > Accessibility > Zoom.
- Set Zoom Region to Full Screen and Enable Zoom.
*Note: When Zoom is enabled, the screen will magnify. Triple-tap the screen with three fingers to reset. Other settings remain unchanged. Android users can skip this step; full features unlock via Bluetooth.
4.4 Phone Settings for Diving
Before placing your phone into the case, ensure optimal performance and prevent interruptions:
- Enable "Do Not Disturb" mode to prevent notifications and interruptions.
- Set your screen to "Stay On" or disable auto-lock to avoid the screen turning off during use.
4.5 Installation Procedure
- Unlock all 5 latches and open the cover of the diving case.
- Remove any existing phone case from your device. Install the bare phone.
- Align your phone's camera lens with the viewport of the diving case. Flush it against the left edge and secure it in the clamp.
- Test: Switch to the widest lens on your phone's camera. If the view is blocked, adjust the phone slightly rightward (e.g., for iPhone 12 Mini).
- Close the cover and lock all latches securely.
- Unscrew the vacuum port (counterclockwise).
- Press the vacuum pump rubber head firmly onto the port and pump 3-4 times to remove air.
- Tighten the vacuum port (clockwise). This prevents air condensation and eliminates lens/screen fogging.
4.6 Attach Safety Leash
Attach the safety hand strap to the designated loop on the diving case. This is essential for freediving or scuba diving when hands-free operation is needed (e.g., for ear equalization or hand signals).

5. Operating Instructions
The diving handle features a five-key operation system for easy control of your phone's camera functions underwater.

- Capture Button (Orange):
- Single Press: Start/stop recording video or take a photo.
- Long Press (2s): Turn on/off the device.
- Mode Button 1 (M): Single Press to switch between shooting modes.
- Mode Button 2 (M): Single Press to switch between shooting modes.
- Zoom Out (W): Zoom out (wide-angle).
- Zoom In (T): Zoom in (telephoto).
Advanced Functions:
- Long press (2s) on a Mode button for front/rear camera switch.
- Long press (2s) on a Zoom button to wake the screen from sleep mode.
5.1 Special Usage Instructions for Samsung Models
Some Samsung models may have specific behaviors:
- These models do not support waking the camera when the screen is off. Please disable auto-lock or set the screen timeout to the maximum.
- Before placing the phone into the case, manually open the camera app with the screen on.
- Supported camera modes are Photo, Video, and More. If you switch to More, you cannot return via the mode button. To go back, press the shutter button once.

6. Maintenance
- Cleaning: After each use, especially in saltwater, rinse the case thoroughly with fresh water. Use the provided mirror cloth to gently clean the lens and screen viewport.
- Drying: Allow the case to air dry completely before storing. Ensure all latches are open during drying to prevent moisture buildup.
- Storage: Store the case in a cool, dry place away from direct sunlight and extreme temperatures.
- Gasket Care: Periodically inspect the rubber gaskets for any signs of wear, cracks, or debris. Clean them gently and ensure they are free of sand or lint to maintain a watertight seal.
- Vacuum Pump: Keep the vacuum pump clean and dry. Store it in a protective manner to prevent damage.
7. Troubleshooting
- Water Leakage: If the watertight safety test fails (tissue is wet), re-check all seals and latches. Ensure no debris is caught in the gaskets. If the issue persists, discontinue use and contact customer support.
- Fogging Inside Case: This usually indicates air condensation. Ensure you use the vacuum pump correctly during installation to remove air from the case. If fogging occurs, remove the phone, dry the case, and re-install, ensuring proper vacuuming.
- Bluetooth Connection Issues:
- Ensure the diving handle is powered on.
- Check your phone's Bluetooth settings to confirm "TELESIN SDC" is visible and paired.
- If the device auto-shuts down, power it on again and attempt to pair within 2 minutes.
- Try restarting both your phone's Bluetooth and the diving handle.
- Buttons Not Responding:
- Verify Bluetooth connection.
- For iOS, ensure the "Zoom" accessibility setting is correctly configured (see Section 4.3).
- For Samsung, ensure the camera app is open and screen auto-lock is disabled (see Section 5.1).
- Check if the phone is properly aligned within the case, allowing the buttons to make contact.
- Blocked Wide-Angle View (iPhone 12 Mini example): If your phone's widest lens view is blocked, adjust the phone slightly rightward within the case during installation.
8. User Tips
- Samsung S25 Ultra Compatibility: This model is compatible with the Samsung S25 Ultra, as it falls within the 5.4-6.9 inch phone size range. Remember to follow the special usage instructions for Samsung models (Section 5.1).
- Pre-Dive Checklist: Always perform the watertight safety test before each dive, especially after long periods of storage or if the case has been subjected to any impact.
- Battery Life: Ensure your phone and the diving handle are fully charged before a dive to avoid interruptions.
- Screen Brightness: Increase your phone's screen brightness to maximum for better visibility underwater.
9. Warranty and Support
TELESIN products are designed for durability and performance. For any questions, technical support, or warranty claims, please refer to the contact information provided with your purchase or visit the official TELESIN website. Please retain your proof of purchase for warranty purposes.