1. Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your NICECNC Electric Starter System Bronze Bushes. These bushes are designed as an upgraded replacement for the original Teflon bushings, which are prone to wear and can lead to damage in the starter system (bendix and/or crown wheel) or engine casing. Made from high-quality bronze with CNC machining, these bushes offer improved durability, reliability, and easier installation.
For additional information and documents, please refer to the official user manual PDF: User manual (PDF).
2. Safety Warnings
- This product is only compatible with specified motorcycle models. Installation on non-compatible vehicles may cause improper fitment, functional failure, or safety hazards.
- Installation must be performed by a qualified motorcycle technician.
- A torque wrench must be used during installation to ensure proper tightening.
- Inspect the part before every ride. Discontinue use immediately if looseness, deformation, or cracks are detected.
- This is an aftermarket replacement or modification part. Its performance may differ from original equipment. Carefully assess your intended usage scenario.
- Do not weld, drill, grind, or otherwise modify this product.
- This product is intended for off-road or closed-course use only and is not E-mark certified. Do not use on public roads unless explicitly labeled as "E-marked."
3. Setup and Installation
3.1 Compatible Models
These bronze bushes are compatible with the following motorcycle models:
- For KTM 250 300 XC/XCW/EXC/TPI 2019-2025
- For HUSQVARNA TE250i/ TE300i 2019-2025
- For Gas Gas 250 300 EC/EX 2021-2025
Note: Some 2019 bikes may have different bushing configurations (two long bushings, or one long and one short). This kit includes two long and one short bush to cover all options.
X Not compatible with any other models. Forced installation may lead to accidents.
3.2 Installation Steps
The installation process involves replacing the original starter system bushings. Follow these steps carefully:
- Park the motorcycle on a level surface and engage the main stand for stability.
- Use appropriate tools to carefully remove the original OEM component (starter system cover and existing bushings).
- Align the new bronze bush(es) with the mounting holes in the engine case and/or ignition cover and insert the included fasteners.
- Tighten all bolts using a torque wrench to the specified torque value. Refer to your motorcycle's service manual for specific torque specifications.
Warning: Never tighten by hand feel! Over-torquing can strip threads; under-torquing may cause the part to detach during riding.
After installation, manually apply pressure to test stability. Ensure there is no unusual noise, play, or movement.
Figure 1: Overview of the NICECNC Electric Starter System Bronze Bushes and the installation tool.
Figure 2: Example of a bronze bush correctly installed in the engine casing, demonstrating a perfect fit.
Figure 3: The 30° chamfer design on the bushes facilitates easier installation with the provided tool.
3.3 Important Installation Notes
When installing bronze bushings, they should be a light press fit in the engine case and cover. It is common for stock bushings to spin in the bushing bore and create wear, resulting in a loose fit. It is essential that new bushings are held securely in place. A retention compound (e.g., Loctite 638 or 648) can be used to secure the bushings. If the bushing bore is badly damaged, it should be repaired or replaced before installing new bushings.
4. Operation
The NICECNC Electric Starter System Bronze Bushes are internal components of your motorcycle's electric starter system. Once correctly installed, they function automatically as part of the starter mechanism, providing a durable and reliable bearing surface for the starter components. No specific user operation is required beyond the normal use of your motorcycle's electric starter.
5. Maintenance Recommendations
- Check fastener tightness every 500 kilometers or once per month, whichever comes first.
- Clean the surrounding area with water and a neutral detergent. Avoid strong acids or alkalis, which can cause corrosion to other engine components.
- If the motorcycle is frequently used in off-road, muddy, or salt-spray environments, increase the inspection frequency of the starter system components.
6. Troubleshooting
If you encounter issues after installation, consider the following:
- Starter System Interference: If the bendix or crown wheel experiences unusual resistance or damage after installation, verify that the bushes are not too thick or improperly seated, causing interference when the crankcase is reassembled. Ensure all components have adequate clearance.
- Loose Fit: If the new bushings feel loose, ensure that the bushing bore in the engine case or cover is not worn or damaged. As noted in the installation section, a retention compound (e.g., Loctite 638 or 648) may be necessary to help secure the new bushings firmly in place if the bore has minor wear. For badly damaged bores, repair or replacement of the engine component is recommended.
- Unusual Noise, Play, or Movement: Re-check all fasteners for proper torque and ensure the bushes are fully seated and stable. If issues persist, consult a qualified motorcycle technician.
7. Specifications
| Feature | Detail |
|---|---|
| Brand | NICECNC |
| Model Name | 1241023201 |
| Condition | 100% Brand new |
| Material | High-quality bronze |
| Processing | CNC-machined |
| Chamfer | 30° for easier installation |
| Surface Treatment | Anodized (prevents rust) |
| Package Contents | 1x Installation Tool, 1x Short Bush (P/N 55140030100 equivalent), 2x Long Bushes (P/N 55540031000 equivalent) |
| Origin | Mainland China |
Figure 4: Dimensions of the installation tool (69mm/2.71" length, 13mm/0.51" diameter) and bushes (12mm/0.47" diameter).
8. User Tips
- Fitment Verification: While the product is designed for specific models (KTM 250/300, Husqvarna TE250i/TE300i, Gas Gas 250/300), some users have reported successful fitment on slightly older models like the 2017 KTM 300 EXC. Always verify compatibility with your specific bike's year and model before installation.
- Bushing Bore Condition: Before installing new bronze bushes, thoroughly inspect the bushing bore in the engine case and cover for wear or damage. If the bore is significantly damaged, it may require repair or replacement to ensure a secure fit and prevent future issues.
- Use of Retention Compound: For optimal security, especially if there is minor wear in the bushing bore, consider using a suitable retention compound (e.g., Loctite 638 or 648) to help hold the new bushings firmly in place.
9. Warranty and Support
For warranty information, technical support, or any issues prior to or after purchase, please contact NICECNC customer service. Refer to the product packaging or the official NICECNC website for contact details.
10. Disposal
At the end of its service life, this product should be disposed of as metal waste. Please utilize local recycling facilities or authorized waste collection services. Do not discard improperly with general household waste.
11. Disclaimer
The manufacturer and EU Authorized Representative shall not be held liable for any damage, injury, or accident resulting from:
- Incorrect or unqualified installation.
- Use beyond the intended scope (e.g., on public roads without E-mark certification).
- Unauthorized modifications to the product.
- Failure to inspect or maintain the product as instructed in this manual.
This manual may be updated without prior notice. Please refer to the latest version for current information.