Instruction Manual

1. Product Overview

This manual provides essential information for the installation, operation, and maintenance of the MACURY V1 Version 60V30A Sine Wave Controller. This controller is specifically designed for the 60V 10-inch KAABO WOLF WARRIOR X PLUS Electric Scooter. Please read this manual thoroughly before installation and use.

Figure 1: MACURY V1 Version 60V30A Sine Wave Controllers (Model A and Model B)

Figure 2: Controller compatibility with KAABO WOLF WARRIOR X PLUS Electric Scooter

2. Compatibility and Important Notes

This controller is designed for specific configurations of the KAABO WOLF WARRIOR X PLUS Electric Scooter. Please ensure your scooter meets the following criteria:

• Scooter Model: KAABO WOLF WARRIOR X PLUS (60V, 10-inch)
• Display Compatibility: The scooter must be equipped with an LT01 or KAABO K1 Version display (V1 version display).
• Display Incompatibility: This controller is NOT compatible with scooters equipped with a TFT Display or a Center Display.
• Hub Box Requirement: The scooter must be equipped with a KAABO (HUB-1) Hub Box for proper installation and function.

Figure 3: Compatible and Incompatible Display Types

Figure 4: Required KAABO (HUB-1) Hub Box

3. Setup and Installation

Professional installation is highly recommended due to the electrical nature of this component. Incorrect installation can lead to damage to the scooter or personal injury.

3.1 Identifying Controller Models

The product includes two distinct controller models:

• Model A: Main Controller for the Rear Motor.
• Model B: Sub Controller for the Front Motor.

Figure 5: Model A (Rear Motor) and Model B (Front Motor) Controllers

Figure 6: Controller Specification Labels

3.2 General Installation Steps (Consult a professional for detailed wiring)

1. Safety First: Ensure the scooter is powered off and the battery is disconnected before beginning any installation.
2. Access Controllers: Locate the existing controllers on your scooter. This typically involves opening a compartment on the scooter deck.
3. Identify Old Controllers: Note which controller is connected to the front motor and which to the rear motor.
4. Disconnect Old Controllers: Carefully disconnect all wiring from the old controllers. Take photos if necessary to aid reassembly.
5. Install New Controllers: Connect the new Model A controller to the rear motor wiring and the new Model B controller to the front motor wiring. Ensure all connections are secure and match the original configuration.
6. Connect to Hub Box: Ensure the controllers are correctly connected to the KAABO (HUB-1) Hub Box.
7. Verify Display Connection: Confirm that your compatible display (LT01 or KAABO K1 Version) is correctly connected.
8. Secure Controllers: Mount the new controllers securely within the scooter's compartment.
9. Reconnect Battery: Once all connections are verified, reconnect the scooter battery.
10. Test Functionality: Power on the scooter and perform a low-speed test to ensure all functions (acceleration, braking, display) are working correctly.

4. Operating Instructions

The sine wave controller is an integral part of your electric scooter's motor system. Once correctly installed, it manages the power delivery to the motors, providing a smoother and more efficient ride compared to traditional square wave controllers. There are no direct user operating controls on the controller itself; its function is automatic based on your scooter's throttle input and other system commands.

• Ensure your scooter's display is functioning correctly to monitor speed, battery level, and other parameters.
• Operate your scooter according to the manufacturer's guidelines for the KAABO WOLF WARRIOR X PLUS.

5. Maintenance

Proper maintenance ensures the longevity and optimal performance of your controller.

• Keep Clean: Periodically inspect the controller and its connections for dirt, dust, or moisture. Clean with a dry, soft cloth.
• Check Connections: Ensure all wiring connections remain tight and free from corrosion. Loose connections can lead to intermittent power or damage.
• Avoid Water Exposure: While controllers are often designed with some water resistance, avoid direct exposure to heavy rain or submersion.
• Temperature Management: Ensure the controller is installed in a location that allows for adequate heat dissipation. Avoid operating the scooter in extreme temperatures for extended periods.
• Professional Inspection: If you notice any unusual behavior, sounds, or smells from your scooter, have it inspected by a qualified technician.

6. Troubleshooting

If your scooter experiences issues after controller installation, consider the following basic troubleshooting steps:

• No Power/Scooter Not Turning On:
  1. Check all battery connections to ensure they are secure.
  2. Verify the main power switch on the scooter is in the 'ON' position.
  3. Ensure the controller's main power input is correctly connected.
• Motor Not Responding/Intermittent Power:
  1. Inspect all motor phase wires and Hall sensor wires for secure connections.
  2. Check for any visible damage to the controller or wiring.
  3. Ensure the throttle is correctly connected and functioning.
• Error Codes on Display:

  Refer to your scooter's display manual for specific error code interpretations. Common issues might relate to motor, Hall sensor, or throttle faults.

• Incorrect Display Functionality:

  Confirm that your scooter has a compatible display (LT01 or KAABO K1 Version). If you have an incompatible display (TFT or Center Display), the controller will not function correctly.

For complex issues or if basic troubleshooting does not resolve the problem, it is recommended to seek assistance from a professional electric scooter technician or contact the seller for support.

7. Specifications

8. Warranty and Support

For any warranty claims, technical support, or assistance with installation and troubleshooting beyond the scope of this manual, please contact the seller or authorized service center where you purchased the product. Keep your purchase receipt as proof of purchase.

9. User Tips

No specific user tips were available from reviews or Q&A for this product. However, general tips for electric scooter controllers include:

• Always ensure all electrical connections are waterproofed if riding in wet conditions.
• Regularly check for any signs of wear or damage to the controller's casing or wiring.
• If upgrading from a different controller type, be aware that performance characteristics (e.g., acceleration curve) may change.