PORTXVNSA NanoVNA-H4 Plus

Contents

PORTXVNSA NanoVNA-H4 Plus Vector Network Analyzer User Manual

Model: NanoVNA-H4 Plus

Measurement Range: 50KHz to 2.7GHz

1. Introduction

The PORTXVNSA NanoVNA-H4 Plus is a versatile Vector Network Analyzer (VNA) designed for HAM radio enthusiasts and RF electronics hobbyists. It features an upgraded measurement range of 50KHz to 2.7GHz, a 4-inch IPS LCD resistive touch screen, and an ergonomic design for enhanced usability. This manual provides essential information for the safe and effective operation of your device.

NanoVNA-H4 Plus with touch screen and knob, displaying measurement range and scanning points.
Figure 1: NanoVNA-H4 Plus with touch screen and knob, displaying measurement range and scanning points.

2. Package Contents

Please check the package contents upon receipt to ensure all items are present:

  • NanoVNA-H4 Plus Unit
  • USB Type-C Data Cable (x2)
  • SMA Male to Male Cable (x2)
  • SMA Female to Female Connector (x1)
  • SMA Simple Calibration Kit (OPEN/SHORT/LOAD) (x1)
  • Stylus (x1)
  • (Optional: 32G Memory Card, depending on purchased variant)
NanoVNA-H4 Plus and its accessories, including cables, adapters, and stylus.
Figure 2: NanoVNA-H4 Plus and its accessories.

3. Setup

  1. Charging the Device: Connect the NanoVNA-H4 Plus to a standard USB power source using one of the provided USB Type-C data cables. The device features a built-in 5000mAh rechargeable battery.
  2. SD Card Insertion: If using an SD card for data storage, carefully insert it into the designated SD card slot.
  3. Initial Power On: Press and hold the power button to turn on the device. The 4-inch IPS LCD touch screen will display the main interface.
  4. Connecting to PC (Optional): For PC control and data analysis, connect the device to your computer using a USB Type-C cable. Install the 'Nano Saver' software on your PC to save Touchstone files, sweep frequency spans, and analyze data.
NanoVNA-H4 Plus connected to a laptop via Type-C port for PC control using Nano Saver software, highlighting 5000mAh battery.
Figure 3: Connecting NanoVNA-H4 Plus to a PC for data analysis.

4. Operating Instructions

4.1 User Interface Navigation

The NanoVNA-H4 Plus features a resistive touch screen and a large rotary knob for intuitive control:

  • Touch Screen: Use the included stylus or your finger to interact with menus and settings. The IPS display offers a wide viewing angle and accurate color reproduction.
  • Rotary Knob: Use the knob for fine adjustments and menu selection.
Close-up of the 4-inch IPS LCD resistive touch screen with stylus for sensitive operation.
Figure 4: Resistive touch screen and stylus for operation.

4.2 Basic Measurements

The device supports a measurement range of 50KHz to 2.7GHz with 401 scanning points. Key measurement capabilities include:

  • Scanning antenna systems and cables
  • SWR and impedance matching
  • Measuring dual-band and triple-band duplexers
  • Port isolation by frequency band
  • Measuring insertion loss of filters
Applications of the NanoVNA-H4 Plus in HAM radio and RF electronics, showing various measurement capabilities.
Figure 5: Diverse applications of the NanoVNA-H4 Plus.

4.3 Performing Measurements

  1. Calibration: Before any critical measurement, perform a calibration using the provided SMA simple calibration kit (OPEN/SHORT/LOAD). This ensures accurate results across the desired frequency range.
  2. Setting Frequency Range: Use the touch screen or rotary knob to set the START and STOP frequencies for your sweep.
  3. Selecting Measurement Type: Navigate through the menus to select the desired measurement parameter (e.g., S11, S21, Smith Chart, SWR).
  4. Connecting Device Under Test (DUT): Connect your antenna, cable, or other RF component to the appropriate SMA port (CH0 or CH1) using the SMA male to male cables or adapters.
  5. Running the Sweep: Initiate the sweep to display the measurement results on the screen.
  6. Saving Data: Use the SD card function to save measurement data for later analysis.
Examples of measurements: 2.7 GHz range, 2.4 GHz antenna, shortwave antennas, cable length.
Figure 6: Examples of various measurements.

4.4 Video Demonstration

Watch this video for a visual guide on navigating the NanoVNA-H4 Plus user interface and performing basic operations.

Video 1: NanoVNA-H4 Plus User Interface Demonstration.

5. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the device. For the screen, a slightly damp, lint-free cloth can be used. Avoid abrasive cleaners or solvents.
  • Battery Care: To prolong battery life, avoid fully discharging the 5000mAh battery frequently. Store the device in a cool, dry place when not in use for extended periods.
  • Storage: Keep the device and its accessories in a protective case to prevent damage from dust, moisture, and physical impact.
  • Connector Care: Ensure SMA connectors are clean and free from debris before connecting cables. Avoid overtightening connections.

6. Troubleshooting

  • Device Not Powering On: Ensure the battery is charged. Connect to a power source and try again.
  • Inaccurate Measurements: Perform a full calibration with the OPEN/SHORT/LOAD kit. Check all cable connections for tightness and integrity. Ensure the correct frequency range and measurement parameters are selected.
  • Touch Screen Unresponsive: Use the 'Touch Test' function in the device settings to check screen responsiveness. If issues persist, try restarting the device.
  • PC Connection Issues: Verify that the USB Type-C cable is securely connected to both the VNA and the PC. Ensure 'Nano Saver' software is correctly installed and updated.

7. Specifications

FeatureSpecification
Measurement Bandwidth50KHz-2.7GHz
Frequency Range50KHz-2.7GHz
Dynamic Range80dB (50KHz-900MHz)
60dB (900MHz-1.5GHz)
50dB (1.5GHz-2.7GHz)
Reflection Coefficient (SWR)<1.1
Frequency Accuracy<0.5 ppm
Frequency Stability<2.5 pp
Display4-inch IPS LCD Resistive Touch Screen
Battery5000mAh Rechargeable Battery
ConnectivityUSB Type-C Port
StorageSD Card Support
Battery IncludedYes
OriginMainland China
CertificationCE

8. User Tips

  • Always Calibrate: For the most accurate measurements, always perform a calibration before starting a new set of measurements, especially when changing frequency ranges or cables.
  • Explore Nano Saver: Utilize the PC software 'Nano Saver' to unlock advanced data analysis and storage capabilities beyond the device's built-in functions.
  • Practice with the Knob and Touch Screen: Familiarize yourself with both the rotary knob and the touch screen for efficient navigation and setting adjustments. The combination offers flexibility in operation.
  • Keep Firmware Updated: Check the manufacturer's website periodically for firmware updates to ensure optimal performance and access to new features.

9. Warranty and Support

This product comes with a standard manufacturer's warranty. For detailed warranty information, technical support, or service inquiries, please refer to the official product website or contact the seller directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.