hiwheel KCQ8.5 Inch with APP pro

Contents

KCQ 8.5-inch Electric Scooter Controller Kit User Manual

Model: KCQ8.5 Inch with APP pro | Brand: hiwheel

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your KCQ 8.5-inch Electric Scooter Controller Kit. This kit is designed for 8.5-inch electric scooters and features a 36V, 15A, 350W controller with APP connectivity for enhanced control and diagnostics. Please read this manual thoroughly before installation and use to ensure safe and optimal performance.

2. Safety First

Strictly adhere to the following safety guidelines:

  • Reversing the positive and negative terminals is strictly prohibited, as it will immediately burn out the controller.
  • Ensure all terminals are fully inserted and securely connected to prevent short circuits or poor contact.
  • The controller must operate within the specified voltage range; do not exceed the rated voltage.
  • The controller's power rating must match the motor's power rating—do not use an undersized controller for an oversized motor.
  • Do not use or store the controller in damp, high-temperature, or flammable/explosive environments.
  • Installation should be performed by qualified personnel with electrical expertise. Non-professionals must not disassemble or attempt repairs.

3. Product Specifications

Feature Specification
Product Name KCQ 8.5-inch Electric Scooter Controller Kit
Rated Voltage DC 36V
Current Limit 15A ± 0.5A
Compatible Motor Power 350W
Battery Connector XT60
Max Speed 25 km/h (Default)
Key Features Speed Control, Cruise Control, Self-Diagnostic, Low Voltage Protection, APP Connectivity
Package Weight 0.57 kg
Package Dimensions (L x W x H) 20 cm x 15 cm x 10 cm

Note: The controller is upgraded to 15A for more powerful performance compared to previous 13A versions.

Close-up of the KCQ Electric Scooter Controller with printed specifications
Close-up view of the KCQ Electric Scooter Controller, showing its printed specifications including voltage, current limit, and compatible motor type.
Certificate of Conformity for Electric Scooter Controller
Certificate of Conformity for the electric scooter controller, indicating compliance with relevant standards.

4. Installation Guide

4.1. Step 1: Removal and Preparation

  1. Locate Original Controller: Open the scooter's footrest cover to find the original controller, typically a rectangular box with an aluminum heat sink and multiple connectors.
  2. Disconnect All Connections:
    • Unplug the motor phase wires.
    • Unplug the motor Hall sensor wires.
    • Unplug the power supply wires.
    • Unplug all function wires: throttle wires, brake wires, instrument panel wires, lighting wires, etc.
  3. Remove Old Controller: Remove the screws securing the controller and carefully take it out.

4.2. Step 2: Install the New KCQ Controller

  1. Position Alignment: Place the new KCQ controller in the original controller's location. Check if any adjustments or expansion of the installation space are needed. Ensure the heat dissipation surface faces outward and remains unobstructed.
  2. Initial Securing: Securely fasten the new controller to the frame using screws. Ensure it is firmly fixed to prevent loosening from riding vibrations.
KCQ controller installed inside an electric scooter deck
Example of the controller installed within the scooter's deck, showing battery and wiring connections.

4.3. Step 3: Wiring Connection (Most Critical Step)

Principle: Connect power cables (thick wires) first, then signal cables (thin wires). Ensure all connectors are fully seated.

  1. Connecting Power Cables: Connect the negative terminal first, then the positive terminal. After connecting, you may temporarily leave the power off.
  2. Connecting Motor Wires:
    • Motor Phase Wires: Connect the controller's three thick phase wires (yellow, green, blue) to the corresponding three phase wires of the motor. Initially, connect them arbitrarily and temporarily secure with zip ties without sealing. Later, match the correct phase through debugging.
    • Motor Hall Sensor Wires: Locate the Hall sensor connectors on both the controller and motor. These typically feature a foolproof design for direct plug-and-play connection. If connectors do not align, manually match each wire according to the wire sequence definition. Secure connections with solder and insulate using heat shrink tubing.
  3. Connect Control Signal Wires (typically plug-in connectors):
    • Throttle Grip: Connect the throttle grip wire to the controller. New kits usually include a new throttle grip for direct plug-in connection.
    • Brake: Connect the brake cable.
    • Instrument Panel/Display: Connect the corresponding instrument wires to display speed, battery level, mode, etc.
    • Other Functions: Connect wires for features like lights, cruise control, or anti-theft alarms as needed.

After completing the connections, a thorough inspection must be conducted to ensure no wiring has been overlooked.

Wiring diagram for the KCQ Electric Scooter Controller
Detailed wiring diagram for the controller, showing connections for battery (XT60), motor phase lines (green, blue, black, red, yellow), communication line, taillight line, and Hall line (red, yellow, green, blue, black).
Wiring diagram for the dashboard of the KCQ Electric Scooter Controller
Detailed wiring diagram for the dashboard, showing connections for communication line, accelerator, brake line, and headlight.
Taillight wiring detail for KCQ Electric Scooter Controller
Close-up of the taillight wiring connection.
Accelerator grip with connector detail for KCQ Electric Scooter Controller
Accelerator grip and its connector detail.

5. Operating Instructions

  • Power On/Off: Short press the button for 0.5 seconds to boot. Long press the button for 2 seconds to shut down.
  • Cycling Mode (Non-Zero Start-Up): The scooter operates in non-zero start-up mode. This means you need to reach a gliding speed of 3 km/h before pressing the accelerator to start the motor.
  • Speed Gear:
    • Default: D gear (20 km/h / 13 MPH), S gear (25 km/h / 16 MPH). The controller has a memory function and defaults to the last used gear.
    • After lifting speed limit (via APP): E gear (15 km/h / 9 MPH), D gear (25 km/h / 16 MPH), S gear (32 km/h / 20 MPH).
  • Brake Method: Hall electronic brake.
  • Tail Lights: When the lights are turned on, the tail lights will flicker during braking.
  • Cruise Control Mode: If the cruise control function is enabled in the APP, the scooter will automatically enter cruise mode 6-8 seconds after the speed control is stable while riding. To exit cruise mode, press the brake, accelerator, or switch gears. If the cruise control function is not enabled in the APP, it will not activate.
  • Self-Learning: For the first power-on, run the no-load speed regulation to the highest speed and hold the throttle to the end for 3 seconds. Then, release the throttle until the motor drives. The controller will automatically learn and save the motor parameters by shutting down after the motor stops.
  • Restore Factory Settings: Press the brakes and accelerators simultaneously, click 8 consecutive times, and wait for the automatic shutdown. Release the brakes and accelerators. The factory settings will be restored when the scooter is powered on again.
KCQ Electric Scooter APP interface showing speed control and settings
The mobile application interface for the KCQ controller, showing speed control, riding time, mileage, and other functions. The app adapts to your mobile phone's system language.
KCQ Electric Scooter APP settings for start mode
APP settings screen illustrating the 'Zero start' and 'Non-zero start' options. 'Zero start' means no initial speed is needed to start.

6. Maintenance

To ensure the longevity and proper functioning of your KCQ Electric Scooter Controller, please observe the following maintenance guidelines:

  • Keep the controller dry and clean. Avoid exposure to dampness, high temperatures, or corrosive environments.
  • Regularly inspect all wiring connections for secure fit and signs of wear or damage. Loose or damaged wires can lead to malfunctions or safety hazards.
  • Ensure the controller's heat dissipation surface remains unobstructed to prevent overheating.
  • Do not attempt to disassemble or repair the controller yourself if you are not a qualified professional. Unauthorized repairs can void the warranty and cause further damage.

7. Troubleshooting

This section provides common fault codes and their solutions:

Code Fault Description Possible Causes Solution
E1 Motor Hall failure Motor Hall sensor damaged Replace the motor.
E2 MOS tube failure
  • Short circuit between motor phase wires
  • Internal controller component damage
  • Inspect motor phase wires for insulation damage or other issues; replace motor.
  • Replace the controller.
E3 Brake failure
  • Damaged brake lever
  • Brake lever not reset before startup
  • Replace the brake lever.
  • Release the brake lever to reset; if error persists, replace the brake lever.
E4 Throttle Fault / Handlebar failure
  • Throttle grip damaged
  • Throttle grip not reset before startup
  • Replace the throttle grip.
  • Release the throttle grip to reset. If error persists, replace the throttle grip.
E5 Undervoltage protection Supply voltage below controller's minimum threshold Charge or replace the battery.
E6 Instrument/Controller communication failure Instrument and controller cannot communicate
  • Check communication cable connections.
  • Inspect motor phase wires or Hall sensor wires for damage/leakage.
  • Replace the motor.
E7 Overvoltage protection Supply voltage exceeds controller's maximum threshold Replace battery with controller-matched voltage or repair motor phase/Hall wire insulation damage causing leakage.
E8 Controller Op-Amp Failure Water ingress damaging internal components or other internal component damage Replace the controller.
E9 Stall Fault / Blockage fault
  • Obstacles prevent motor rotation, causing motor lockup
  • Incorrect wiring sequence between motor and controller
  • Loosen the throttle grip and remove the obstruction.
  • Return the motor to the controller manufacturer for re-calibration.
E0 Thermal Protection Motor reaches thermal protection threshold, instrument displays E0, motor stops. Wait for the motor to cool down until the temperature falls below the set value before resuming normal operation.

7.1. Motor Wiring Debugging

If the motor experiences noise, shakes, vibrates but doesn't run smoothly, or runs smoothly but in reverse, you may need to adjust the Hall lines or phase lines.

A. Adjusting Hall Lines (Motor noise/vibration)

If the motor makes noise, shakes, vibrates but doesn't run, adjust the Hall lines. Test the 6 methods shown in the diagram one by one and choose the one that results in the smoothest operation.

Motor Hall line adjustment diagram for electric scooter
Diagram illustrating 6 methods for adjusting Hall line connections (Y: Yellow, G: Green, B: Blue wire) to resolve motor noise or vibration issues.

B. Adjusting Phase Lines (Motor reversal)

If the motor runs smoothly but in reverse, adjust the phase line connections as shown in the diagram until it runs correctly.

Motor phase line adjustment diagram for electric scooter
Diagram illustrating 6 methods for adjusting phase line connections (Y: Yellow, G: Green, B: Blue wire) to correct motor reversal.

8. Warranty and Support

The warranty for this product does not cover water damage or wire damage. It is strongly recommended that installation and any repairs be performed by qualified personnel with electrical expertise. Non-professionals should not attempt to disassemble or repair the controller.

For further assistance or inquiries, please contact your seller or a certified service center.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.