Lishui Controller LSW06-90B1AFSB-U

Contents

LSW06-90B1AFSB-U Brushless Motor Controller Instruction Manual

Model: LSW06-90B1AFSB-U | Brand: Lishui Controller

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the LSW06-90B1AFSB-U Brushless Motor Controller. Designed for electric bicycles, electric scooters, fat bikes, and MTBs, this controller ensures efficient and reliable performance for your electric drive system. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Safety Guidelines

Always observe the following safety precautions to prevent injury or damage to the controller and your vehicle:

  • Ensure the power supply is disconnected before performing any installation or maintenance.
  • Verify that the voltage and current ratings of the controller match your motor and battery specifications.
  • Avoid exposing the controller to water, excessive moisture, or extreme temperatures.
  • Do not attempt to open or modify the controller casing, as this may void the warranty and cause malfunction.
  • All wiring connections must be secure and properly insulated to prevent short circuits.
  • If you are unsure about any part of the installation or operation, consult a qualified technician.

3. Specifications

Close-up of LSW06-90B1AFSB-U controller label showing specifications.

Figure 1: Controller label with key specifications.

The label on the controller displays key specifications: Vrated 36V, I rated 7A, Vcutoff 31.5V, I max 14A, Part No. LSW06-90B1AFSB-U, Prod. Date 05/2025, Serial No. X25050115, and Comments LSW1037-08-01EA.

Table 1: Technical Specifications
FeatureSpecification
ModelLSW06-90B1AFSB-U
TypeController
Rated Voltage (Vrated)36V
Rated Current (I rated)7A
Maximum Current (I max)14A
Voltage Cutoff (Vcutoff)31.5V
Display Meter CompatibilityKDS
Dimensions (L x W x H)94mm x 49mm x 29mm
Product Weight190g
Package Dimensions (L x W x H)12cm x 8cm x 9cm
OriginMainland China
Dimensions of the LSW06-90B1AFSB-U controller.

Figure 2: Controller dimensions.

This diagram illustrates the physical dimensions of the controller: 94mm length, 49mm width, and 29mm height.

4. Package Contents

The package typically includes:

  • 1 x LSW06-90B1AFSB-U Brushless Motor Controller
  • (Additional accessories may vary by retailer)

5. Installation

Before installation, ensure your vehicle's power is off and the battery is disconnected. It is crucial to match the controller's protocol with your existing display meter and other components. If protocols differ, the controller may not function correctly.

Wiring diagram for LSW06-90B1AFSB-U controller connections.

Figure 3: Wiring Diagram.

This detailed wiring diagram illustrates the connections for the LSW06-90B1AFSB-U controller. Ensure each connection is made correctly according to the labels:

  1. Positive Pole (1): Connect to the positive terminal of your battery.
  2. Negative Pole (2): Connect to the negative terminal of your battery.
  3. Motor Cables (3, 4, 5): Connect these three phase wires to the corresponding motor phase wires.
  4. Light (6, 7): Connect to your vehicle's lighting system.
  5. Sensor (8): Connect to the vehicle's sensor input.
  6. Motor Hall & Speed Signal (9): Connect to the motor's Hall sensors and speed signal wire.
  7. Ebike Main Cable (10): This is the primary connection point for other e-bike components, such as the display, throttle, and brake levers.

After making all connections, secure the controller in a safe, dry location on your vehicle, away from direct impact or excessive vibration. Double-check all connections before reconnecting the battery and powering on the system.

6. Operation

The LSW06-90B1AFSB-U controller acts as the "Brain of the E-bike," managing energy and processing signals from various external parts. Once properly installed and connected to your battery, motor, display, throttle, and other accessories, the controller will regulate power output to the motor based on your input.

  • Power On/Off: Use your vehicle's main power switch or display unit to turn the system on or off.
  • Throttle Control: The throttle input (connected to Ebike Main Cable) will dictate the motor's speed.
  • Pedal Assist System (PAS): If your vehicle has a PAS, the controller will interpret pedal sensor signals to provide motor assistance.
  • Brake Levers: When brake levers are engaged, the controller will cut power to the motor for safety.
  • Display Unit: Your KDS display unit will show real-time information such as speed, battery level, and error codes.

The controller supports advanced features like Frontier Hall-Sensorless Motor Technology and is designed for high stability and quality, ensuring a low failure rate.

7. Maintenance

To ensure the longevity and optimal performance of your LSW06-90B1AFSB-U controller, follow these maintenance guidelines:

  • Regular Inspection: Periodically check all wiring connections for looseness or damage.
  • Cleaning: Keep the controller clean and free from dust, dirt, and debris. Use a dry, soft cloth for cleaning. Do not use water or cleaning agents directly on the controller.
  • Environmental Protection: Protect the controller from direct sunlight, rain, and extreme temperatures.
  • Avoid Overloading: Do not exceed the controller's maximum current (14A) to prevent overheating and damage.
  • Firmware Updates: If available, ensure your controller's firmware is up-to-date. Lishui Controller offers OTA (Over-The-Air) functions compatibility for updates.

8. Troubleshooting

If you encounter issues with your controller, refer to the following common problems and solutions:

Table 2: Common Troubleshooting Steps
ProblemPossible CauseSolution
Controller not powering onLoose battery connection, faulty battery, main power switch off.Check battery connections, ensure battery is charged, verify main power switch is on.
Motor not responding to throttleLoose throttle connection, faulty throttle, motor phase wires disconnected.Inspect throttle wiring, check motor phase wire connections (3,4,5).
Incompatible components (e.g., display)Different communication protocols between controller and other parts.Ensure all components (especially the display meter) use compatible communication protocols with the LSW06-90B1AFSB-U controller. Consult the seller if unsure about compatibility before purchase.
Error codes on displaySensor malfunction, motor hall sensor issue, over-voltage/under-voltage.Refer to your KDS display manual for specific error code meanings. Check sensor (8) and motor hall (9) connections. Verify battery voltage.
Controller overheatingExcessive load, poor ventilation, prolonged use at maximum power.Reduce load, ensure controller has adequate airflow, allow for cool-down periods.

If the problem persists after attempting these solutions, please contact customer support.

9. User Tips

  • Check Compatibility First: Before purchasing, always compare your existing controller's label and specifications with the LSW06-90B1AFSB-U. Pay close attention to voltage, current, and especially the communication protocol (e.g., KDS display meter). Different protocols will lead to errors and non-functionality.
  • Professional Installation Recommended: While the wiring diagram is provided, if you are not experienced with electrical installations, consider seeking professional help to ensure correct and safe setup.
  • Secure Wiring: Ensure all connections are tight and properly insulated to prevent intermittent issues or short circuits during rides.

10. Certifications

Lishui Controller products, including this model, adhere to high quality and safety standards. The company holds the following certifications:

  • ISO 9001: Quality Management System
  • RoHS: Restriction of Hazardous Substances
  • EN 15194:2017: European standard for electrically power assisted cycles (EPAC bicycles).
  • EN ISO 13849-1:2015: Safety of machinery - Safety-related parts of control systems.
  • UL 2849: Standard for Electrical Systems for eBikes.
  • UL 2272: Standard for Electrical Systems for Personal E-Mobility Devices.

11. Warranty and Support

Lishui Controller is committed to providing reliable products and excellent customer service. For warranty information, technical support, or any inquiries regarding your LSW06-90B1AFSB-U controller, please refer to the contact information below. Keep your purchase receipt as proof of purchase for warranty claims.

12. Contact Information

For further assistance, you may contact Nanjing Lishui Electronics Research Institute Co., Ltd.:

Nanjing Lishui Electronics Research Institute Co., Ltd. (Headquarters)

  • Address: No.9 Shuibao Road, Yongyang Town, Lishui District, Nanjing, 211200, P.R.China
  • Tel: +86-25-5720-2368 / +86-25-5720-7820
  • Fax: +86-25-5721-2368
  • Email: sales@lsdzs.com
  • Website: lsdzs.com

EU R&D Center

  • Address: Am Bahnhof 21, 53757 Sankt Augustin, Germany
  • Mobile: +49 15221467527
  • Tel: +49-2241-9454576
  • Fax: +49-2241-9454577
  • Email: info@lsee.eu

Taiwan Office

  • Address: No.450, Fuxing Rd., Taoyuan Dist., Taoyuan City 330, Taiwan
  • Tel: +886 3-333 2298
  • Fax: +886 3-333 3843

13. Further Resources

For a comprehensive overview and additional documentation, you may refer to the official user manual PDF:

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.