1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Lishui LSW06-90B1AFSB-U Brushless Motor Controller. This controller is designed for electric bicycles, electric scooters, fat bikes, and MTB applications. Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Safety Information
- Always disconnect power before installing or performing maintenance on the controller.
- Ensure all connections are secure and correctly polarized to prevent damage to the controller or other components.
- Avoid exposing the controller to water or extreme temperatures.
- If you are unsure about any installation steps, consult a qualified technician.
3. Product Overview
The LSW06-90B1AFSB-U is a 36V, 15A brushless motor controller featuring J protocol communication. It is equipped with double Hall twelve disk sensors and supports a low-level brake mode.
3.1. Controller Label and Specifications

The label on the controller provides essential information:
- Part No.: LSW06-90B1AFSB-U
- Vrated: 36V
- I rated: 7A
- Vcutoff: 31.5V
- I max: 15A
- Prod. Date: 01/2025
- Serial No.: X25010101
- Comments: LSW1037-03-01EA
3.2. Product Dimensions

The controller measures approximately 93mm (length) x 49mm (width) x 29mm (height).
3.3. Wiring Diagram

The controller features various connections for integration into your e-bike system:
- 1: Battery Negative
- 2: Battery Positive
- 3, 4, 5: Motor cable (typically three phase wires)
- 6: Display (5-pin connector for J protocol display)
- 7: Sensor (Hall sensor connection)
- 8: Tachymeter signals
- 9, 10: Light connections
For a visual representation of the controller and its wiring, please refer to the following images:



4. Setup and Installation
Before installation, ensure your e-bike system is compatible with a 36V, 15A controller and uses the J protocol for display communication. Incompatible protocols will lead to errors and improper function.
- Power Disconnection: Turn off your e-bike and disconnect the battery before starting any installation.
- Mounting: Securely mount the controller in a protected area on your e-bike, away from direct exposure to water or excessive heat.
- Battery Connection: Connect the Battery Negative (1) and Battery Positive (2) wires to your e-bike's battery. Ensure correct polarity.
- Motor Connection: Connect the three Motor cable wires (3, 4, 5) to your e-bike's motor. These are typically color-coded (e.g., yellow, green, blue).
- Display Connection: Connect the 5-pin display connector (6) to your J protocol compatible display unit.
- Sensor Connection: Connect the sensor wires (7) to your e-bike's Hall sensors. This controller is designed for double Hall twelve disk sensors.
- Tachymeter and Light Connections: Connect the tachymeter signal wires (8) and light wires (9, 10) if your system includes these components.
- Brake Connection: This controller operates with a low-level brake mode. Ensure your brake levers are compatible and correctly wired.
- Final Check: Double-check all connections for security and correctness before reconnecting the battery and powering on the system.
Important: Verify the model number and display protocol of your original controller before purchasing and installing this unit. Mismatched protocols will prevent the controller from working correctly.
5. Operating Instructions
Once installed and powered on, the controller works in conjunction with your J protocol communication display to manage your e-bike's motor functions.
- Power On/Off: Use your e-bike's display unit to power the system on or off.
- Booster Gears: The controller supports five booster gears, controlled via the display:
- First Gear: 9A (approx. 11km/h)
- Second Gear: 10A (approx. 14km/h)
- Third Gear: 11A (approx. 17km/h)
- Fourth Gear: 13A (approx. 21km/h)
- Fifth Gear: 15A (approx. 25km/h)
- Gear 0: Motor does not operate.
- 6KM/H Cart Function: The controller includes a 6KM/H cart function, typically activated via a button on your display or throttle.
- Throttle Control: Use the throttle for direct speed control, if applicable to your e-bike setup.
- Brake Operation: Engaging the brake levers will cut power to the motor due to the low-level brake mode.
For a general visual overview of the product, you may refer to this video:
6. Maintenance
- Regular Inspection: Periodically check all wiring and connectors for signs of wear, corrosion, or loose connections.
- Cleaning: Keep the controller clean and free from dust, dirt, and moisture. Use a dry, soft cloth for cleaning. Do not use harsh chemicals or solvents.
- Avoid Overheating: Ensure the controller has adequate ventilation and is not covered, especially during prolonged use, to prevent overheating.
- Professional Service: For any internal issues or complex repairs, seek professional service. Do not attempt to open or repair the controller yourself, as this may void the warranty.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Controller reports error / Does not work properly | Incompatible display protocol (e.g., not J protocol). | Ensure your display unit uses the J protocol. This controller is specifically designed for J protocol communication. Contact customer service with a photo of your original controller's label to verify compatibility before purchase. |
| Motor not responding | Loose wiring, power issue, or motor/Hall sensor fault. | Check all power and motor connections. Verify battery charge. Inspect Hall sensor wiring. |
| Intermittent power loss | Loose battery connection or damaged wiring. | Secure battery connections. Inspect wiring for damage and repair if necessary. |
8. Specifications
| Feature | Detail |
|---|---|
| Model | LSW06-90B1AFSB-U |
| Type | Brushless Motor Controller |
| Rated Voltage (Vrated) | 36V |
| Rated Current (I rated) | 7A |
| Max Current (I max) | 15A |
| Cutoff Voltage (Vcutoff) | 31.5V |
| Display Protocol | J protocol |
| Brake Mode | Low level |
| Sensors | Double Hall twelve disk sensors |
| Booster Gears | 5 gears (9A/11km/h, 10A/14km/h, 11A/17km/h, 13A/21km/h, 15A/25km/h) |
| Special Functions | 6KM/H cart function |
| Dimensions (L x W x H) | 93mm x 49mm x 29mm |
| Product Weight | 183g |
| Origin | Mainland China |
9. User Tips
- Compatibility Check: Always verify the model number and display protocol of your existing controller before purchasing a replacement to ensure compatibility. Sending a photo of your old controller's label to customer service can help prevent issues.
- Protocol Mismatch: Be aware that if the new controller's protocol (e.g., J protocol) does not match your e-bike's display, it will not function correctly and may report errors.
10. Warranty and Support
Lishui Controller products are manufactured by Nanjing Lishui Electronics Research Institute Co., Ltd., a company with over 40 years of experience in controller development and production. They adhere to high-quality standards and have sold millions of controllers worldwide.
For technical support, warranty claims, or further inquiries, please contact the seller or Lishui Controller customer service. You may also refer to the official user manual PDF for additional details: Lishui Controller User Manual (PDF).
Lishui Controller has a dedicated R&D team and a robust quality assurance system, ensuring reliable solutions and a low failure rate.