NICECNC Front & Rear Lowering Kit

1. Product Overview

The NICECNC Front & Rear Lowering Kit is designed to reduce the motorcycle's height by 20mm, providing an optimal seat height for shorter riders while maintaining chassis performance and riding dynamics. Manufactured from high-quality 7075 aluminum and 304 stainless steel, this kit is engineered for durability and precise fitment.

2. Safety Warnings

• This product is only compatible with specified motorcycle models. Installation on non-compatible vehicles may cause improper fitment, functional failure, or safety hazards.
• Installation must be performed by a qualified motorcycle technician.
• A torque wrench must be used during installation.
• Inspect the part before every ride. Discontinue use immediately if looseness, deformation, or cracks are detected.
• This is a non-OEM (aftermarket) part. Its performance may differ from original equipment—please carefully assess your intended usage scenario.
• Do not weld, drill, grind, or otherwise modify this product.

3. Compatible Models

This lowering kit is designed for specific KTM and Husqvarna models. Please verify your motorcycle's make, model, and year against the list below to ensure compatibility. Using this kit on incompatible models may lead to accidents and functional issues.

KTM Models (2024-2025):

• KTM 150 250 300 XC-W/EXC
• KTM 250 350 500 EXC-F
• KTM 350 500 XW-F
• KTM 450 XCF-W

Husqvarna Models (2024-2025):

• Husqvarna FE 250 350 450 501
• Husqvarna TE 150 250 300

Warning: Not compatible with any other models. Forced installation may lead to accidents.

4. Installation Steps

For detailed visual instructions, please refer to the official user manual PDF: User Manual (PDF).

1. Park the motorcycle on a level surface and engage the main stand.
2. Use appropriate tools to remove the original OEM component.
3. Align the new part with the mounting holes and insert the included fasteners.
4. Tighten all bolts using a torque wrench to the specified torque value.

Caution: Never tighten by hand feel! Over-torquing can strip threads; under-torquing may cause the part to detach during riding.

After installation, manually apply pressure to test stability. Ensure there is no unusual noise, play, or movement.

5. Operating Considerations

Once installed, the lowering kit provides a 20mm reduction in height, optimizing the motorcycle's stance for riders seeking a lower seat position. The design ensures a perfect compromise between chassis performance and height, allowing for unrestricted riding dynamics. Always ensure all components are securely fastened before operation.

6. Maintenance Recommendations

• Check fastener tightness every 500 kilometers or once per month.
• Clean with water or a neutral detergent. Avoid strong acids or alkalis, which may cause corrosion.
• If used in off-road, muddy, or salt-spray environments, increase inspection frequency.

7. Troubleshooting

If you experience any unusual noise, play, or movement after installation, re-check all fasteners for proper torque. Ensure the kit is correctly aligned and installed according to the instructions. If issues persist, discontinue use and consult a qualified motorcycle technician or contact NICECNC customer support.

8. Specifications

9. User Tips

• Users have reported satisfaction with the product's quality and fitment when installed correctly on compatible models.
• Ensure you have the necessary mechanical knowledge, skills, and tools before attempting installation. If unsure, seek professional assistance.
• Always double-check compatibility with your specific motorcycle model and year to avoid issues.

10. Disposal

At the end of its service life, dispose of this product as metal waste through local recycling or authorized waste collection facilities. Do not discard improperly.

11. Disclaimer

The manufacturer and EU Authorized Representative shall not be held liable for any damage, injury, or accident resulting from:

• Incorrect or unqualified installation
• Use beyond the intended scope (e.g., on public roads without E-mark certification)
• Unauthorized modifications
• Failure to inspect or maintain the product as instructed

This manual may be updated without prior notice. Please refer to the latest version for current information.

12. Frequently Asked Questions (FAQ)

Q: Is this kit compatible with a KTM 2018 Sixdays 450?

A: Based on the product specifications, this kit is designed for KTM 450 XCF-W 2024-2025 models. Please refer to the "Compatible Models" section for the full list of supported motorcycles. Using the kit on incompatible models may lead to improper fitment and safety issues.

13. Support

For any questions, technical assistance, or support regarding your NICECNC Front & Rear Lowering Kit, please contact NICECNC customer service through their official channels. Ensure you have your product model number (1272001906) ready when contacting support.