Lishui Controller X035-AB001

Contents

X035-AB001 Ebike Brushless Motor Controller User Manual

Model: X035-AB001

Brand: Lishui Controller

This manual provides detailed instructions for the installation, operation, and maintenance of the X035-AB001 Ebike Brushless Motor Controller, designed for electric bicycles, scooters, and MTBs.

1. Introduction

The X035-AB001 Brushless Motor Controller is engineered for electric bicycles, electric scooters, fat bikes, and mountain bikes (MTB). It is designed to provide efficient and reliable control over your e-bike's motor system.

Important Note:

This controller is exclusively compatible with 5S protocol display meters. If your existing display meter uses a different protocol, the controller will not function correctly and may report an error. Before purchasing or installing, please verify the model number of your controller and display meter. For assistance, contact customer service with photos of your controller's label and connectors to ensure compatibility.

2. Specifications

FeatureSpecification
ModelX035-AB001
TypeController
Battery Voltage48V
Cutoff Voltage39V
Current Limit18A
Display Meter Protocol5S
Dimensions (L x W x H)98mm x 64mm x 32mm
Product Weight244g
OriginMainland China

Close-up of X035-AB001 brushless motor controller label showing model number, battery voltage, cutoff voltage, current limit, and display meter protocol.Figure 2.1: Controller label with key specifications.

Dimensions of the X035-AB001 controller: 98mm length, 64mm width, 32mm height.Figure 2.2: Controller dimensions.

3. Components Overview

The X035-AB001 controller features multiple connectors for integrating with various e-bike components. Understanding each connection is crucial for proper installation.

X035-AB001 Ebike Brushless Motor Controller with all wires and connectors visible.Figure 3.1: X035-AB001 Controller with all connections.

Top view of X035-AB001 controller showing various connectors.Figure 3.2: Close-up of controller connectors.

Side view of X035-AB001 Ebike Brushless Motor Controller.Figure 3.3: Side view of the controller.

4. Installation and Wiring

Proper wiring is essential for the safe and correct operation of your e-bike. Refer to the detailed wiring diagram below for connecting the controller to your e-bike system.

Wiring diagram for X035-AB001 brushless motor controller, labeling Ebike Main Cable, Motor Hall, Tachymeter Signal, Cell Phone Holder, Battery Positive, Battery Negative, and Motor Cable connections.Figure 4.1: X035-AB001 Controller Wiring Diagram.

  1. Ebike Main Cable (1): Connect this to the main power and signal harness of your e-bike.
  2. Motor Hall (3): Connect to the Hall sensor wires of your motor. Ensure correct phase matching.
  3. Tachymeter Signal (4): Connect to the tachymeter signal input, typically from the motor or display.
  4. Cell Phone Holder (5): This connection is for accessories like a cell phone holder, if applicable.
  5. Battery Positive (6): Connect the positive terminal of your 48V battery.
  6. Battery Negative (7): Connect the negative terminal of your 48V battery.
  7. Motor Cable (8, 9, 10): Connect these three phase wires to your brushless motor. Ensure correct phase sequence for smooth operation.

Crucial Compatibility Check:

As mentioned, this controller requires a 5S protocol display meter. Connecting it to a display with a different protocol will result in malfunction. Always verify compatibility before finalizing connections.

Video 4.1: Product overview and wiring demonstration.

5. Operating Instructions

Once correctly installed and connected to a compatible 5S protocol display meter, the controller will manage the power delivery to your e-bike's motor based on your input from the throttle and pedal assist system (PAS).

  • Power On/Off: Use your e-bike's main power switch or display unit to turn the system on or off.
  • Speed Control: Adjust speed using the throttle or by engaging the pedal assist system. The controller will regulate motor output accordingly.
  • Display Feedback: The 5S display meter will show real-time information such as speed, battery level, and assist mode.

6. Maintenance

To ensure the longevity and optimal performance of your X035-AB001 controller, follow these maintenance guidelines:

  • Keep Clean and Dry: Regularly clean the exterior of the controller to prevent dust and dirt buildup. Ensure it remains dry and protected from moisture.
  • Avoid Physical Damage: Protect the controller from impacts and vibrations that could damage internal components.
  • Temperature Control: Avoid exposing the controller to extreme temperatures, both hot and cold, as this can affect its performance and lifespan.
  • Inspect Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.

7. Troubleshooting

If you encounter issues with your X035-AB001 controller, consider the following common problems and solutions:

  • Issue: Controller not functioning or displaying an error code.

    Possible Cause: Incompatibility with the display meter protocol.

    Solution: Verify that your display meter uses the 5S protocol. This controller is strictly designed for 5S protocol meters. If your display is not 5S, it will not work. Contact customer service for guidance and to confirm compatibility with your specific setup.

  • Issue: Motor not responding or erratic behavior.

    Possible Cause: Loose or incorrect wiring connections (e.g., motor phase wires, Hall sensor wires).

    Solution: Carefully inspect all wiring connections as per the installation section (Figure 4.1). Ensure all plugs are fully seated and wires are not damaged. Check for correct phase matching for the motor Hall sensors.

  • Issue: Intermittent power or system shutdowns.

    Possible Cause: Low battery voltage or poor battery connections.

    Solution: Ensure your 48V battery is fully charged and its connections to the controller are secure. Check the battery's health and voltage output.

For persistent issues, refer to the "Additional Resources" section for the full user manual PDF or contact Lishui Controller's customer support.

8. User Tips

No specific user tips are available from customer reviews or Q&A at this time. However, general best practices for e-bike controllers include:

  • Always double-check all connections before powering on your e-bike after any installation or maintenance.
  • If you are unsure about any wiring, consult a professional e-bike technician.
  • Keep your e-bike's battery charged to prolong its lifespan and ensure consistent controller performance.

9. Warranty and Support

Lishui Controller is committed to providing reliable solutions and excellent service. While specific warranty details are not provided in this document, Lishui Controller maintains a low failure rate and offers a quick response after-sales team.

For any support inquiries, technical assistance, or warranty claims, please contact Lishui Controller directly. You may find contact information in the official Lishui Controller Brochure or on their website.

Lishui Controller Contact Information (from brochure):

  • Nanjing Lishui Electronics Research Institute Co., Ltd (P.R.China)
    • Add: No.9 Shuibao Road, Yongyang Town, Lishui District, Nanjing, 211200, P.R.China
    • Tel: +86-25-5720-2368 / +86-25-5720-7820
    • Fax: +86-25-5721-2368
    • Email: sales@lsdzs.com
  • EU R&D Center (Germany)
    • Add: Am Bahnhof 21, 53757 Sankt Augustin, Germany
    • Mobile: +49 15221467527
    • Tel: +49-2241-9454576
    • Fax: +49-2241-9454577
    • Email: info@lsee.eu
  • Taiwan Office
    • Add: No.450, Fuxing Rd., Taoyuan Dist., Taoyuan City 330, Taiwan
    • Tel: +886 3-333 2298
    • Fax: +886 3-333 3843

10. Additional Resources

For a more comprehensive guide and detailed documentation, you can view the official user manual in PDF format:

View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.