G-NiceRF DMR858M

Contents

G-NiceRF DMR858M Digital Walkie Talkie RF Module Instruction Manual

Model: DMR858M

1. Introduction

The DMR858M is a cost-effective 5W full-function digital walkie-talkie module developed by G-NiceRF. It is designed to be compatible with analog walkie-talkies commonly used in the market and features DMR Tier II digital walkie-talkie functionality. The module integrates a Moto AMBE++ vocoder, microcontroller, digital walkie-talkie chip, RF power amplifier, and audio amplifier.

Users can easily integrate this module into various handheld devices by connecting external components such as power supplies and speakers. It supports 16 adjustable frequency channels and offers an ultra-compact size for convenient embedding. The DMR858M is produced and tested using lead-free technology, complying with RoHS and Reach standards.

Video: Overview of DMR818S and DMR828S modules, their features, and certifications.

2. Key Features

  • Frequency Bands: UHF (400~470 MHz), VHF (134~174 MHz), 350 band (320~400 MHz)
  • Communication Range: Up to 7-8 Km
  • Power Output: 5W (High Power), 2W (Low Power)
  • High Sensitivity: -120dBm
  • Bit Error Rate: Down to 5% under -117dBm
  • Bandwidth: Analog (12.5 / 25 KHz), Digital (6.25KHz)
  • Messaging: Message transmission and reception, supports SMS sending function
  • Modes: DMR/Analog walkie talkie, built-in standard DMR protocol
  • Power Management: Supports low power sleep mode
  • Advanced Features: Dual time-slot walkie-talkie, repeater compatible, automatic tail sound elimination
  • Design: Highly integrated, cost-effective, compact design for easy embedding

3. Technical Specifications

3.1 General Parameters

ParameterTest ConditionMin.Typ.Max.Unit
Voltage range3.78.08.5V
Operating Temperature-202560°C
Frequency range@UHF400470MHz
@VHF134174MHz
@350320400MHz
Uart baud rate57600bps

3.2 Current Consumption

ParameterTest ConditionMin.Typ.Max.Unit
Sleep current@CS pulled low for 3 seconds< 0.1mA
Rx current< 165mA
Tx current (high power)@VCC=8V, 5W900mA
Tx current (high power)@VCC=8V, 2.5W1700mA
Tx current (low power)@VCC=8V, 2W640mA
Tx current (low power)@VCC=8V, 2.5W1000mA

3.3 Digital Emission

ParameterValueUnit
Frequency Error0.5ppm
4FSK Transmission BER≤1×10-4
Adjacent Channel Power (dB)+/-25KHz≤-68dB

3.4 Sensitivity and Audio

ParameterTest ConditionMin.Typ.Max.Unit
Rx sensitivity (Analog)@12dB SINAD-120dBm
Receiving BER (DMR modulation)@-117dBm5%
Receiving S/N1.5K Frequency Deviation40dB
Adjacent Channel Selectivity12.5KHz Channel Spacing62dB
Intermodulation Immunity12.5KHz Channel Spacing63dB
Blocking ImmunityInterference Frequency Interval > 1M88dB
Audio Output Amplitude (Lineout)F0=1KHz0.2130460mV
Audio Output Impedance (SPK)8Ohm
Audio DistortionF0=1KHz5%
Audio Response300Hz+6dB
500Hz+6dB
1KHz0dB
2KHz-6dB
3KHz-12dB

3.5 Digital Receiving

ParameterTest ConditionValueUnit
Receiving BER (DMR modulation)@-117dBm4%
Adjacent Channel Selectivity (ACS)Offset +12.5KHz60dB
Offset -12.5KHz
IntermodulationOffset +50/100KHz63dB
Offset -50/100KHz
BlockingOffset +/-1MHz87dB
Offset +/-5MHz

3.6 Analog Transmission

ParameterTest ConditionMin.Typ.Max.Unit
Max Modulation Deviation12.5KHz Frequency Deviation (N)2.22.5KHz
25KHz Frequency Deviation (W)4.55.0KHz
Modulation Sensitivity1.5KHz/2.5KHz Frequency Deviation4710mV
Audio Modulation Distortion1.5KHz/2.5KHz1%
Modulation CharacteristicsFrequency Deviation
300Hz-13-11-9dB
500Hz-9-6-3dB
1KHz-30+3dB
2KHz367dB
3KHz71111dB
CTCSS modulation frequency offset350400600Hz
Receiving SNR1.5KHz/2.5KHz (N/W)384050dB

3.7 Physical Dimensions

  • Length: 13 cm
  • Width: 9 cm
  • Height: 8 cm
  • Weight: 0.2 kg
Mechanical dimensions of the DMR858M module, showing length, width, and height measurements.
Figure 3.7.1: Mechanical dimensions of the DMR858M module.

4. Setup Instructions

4.1 Module Components

DMR858M module with labeled components including DIP Switch, Antenna Interface, Potentiometer, PTT Button, USB Port, Microphone, 16 Frequency channel, Communication mode and setup mode switch.
Figure 4.1.1: DMR858M Module Components.

4.2 Pin Definitions

The DMR858M module features various pins for power, communication, and audio. Refer to the table below for detailed pin definitions:

Pin NO.Pin NameDescription
1VCCPositive supply
2,4GNDGround
3CSModule sleep enable pin, "0" for sleep mode, "1" for active mode
5PTTTransmit/receive control pin, "0" for transmit mode, "1" for receive mode, default is receive mode
6LINE_OUTAudio output
7816 Channels, Code 8421, 8th, default output "1"
8416 Channels, Code 8421, 4th, default output "1"
9216 Channels, Code 8421, 2nd, default output "1"
10116 Channels, Code 8421, 1st, default output "1"
11OUTPAudio output, connect to speaker 8Ω, 2W and 4Ω, 5W
12OUTNAudio output, connect to speaker 8Ω, 2W and 4Ω, 5W
13MIC-Negative terminal of the external microphone
14MIC+Positive terminal of the external microphone (internal bias provided, no additional power supply required)
16SPKENReceive indicator pin, normally low, turns high when a signal is received
18TXDSerial data transmission port
19RXDSerial data transmission port
20,23,24NC
21HST_TXSerial data transmission pin (used for firmware upgrade)
22HST_RXSerial data receive pin (used for firmware upgrade)
DMR858M module with pin numbers labeled for easy identification.
Figure 4.2.1: DMR858M Pinout Diagram.

4.3 Basic Connection Diagram

Basic connection diagram for the DMR858M module, showing connections to MCU, LDO, Antenna, Speaker, and Microphone.
Figure 4.3.1: Basic Connection Diagram.

4.4 Antenna Selection

The antenna is a critical component for the communication system. Its performance directly impacts the overall communication quality. This module requires antennas with an impedance of 50 Ohm. Common antenna types include rubber straight antennas, sucker antennas, and telescopic antennas. Users should select an antenna appropriate for their specific application environment. For optimal performance, G-NiceRF recommends using antennas from their company.

5. Operating Instructions

5.1 Channel Configuration

The DMR858M module comes with 16 default channels: CH0~CH7 operate in DMR mode, and CH8~CHF operate in analog mode. All parameters, including channel settings, can be configured via serial instructions.

5.2 Parameter Configuration via PC Software

The DMR858M module offers a standard serial port, allowing users to configure and read related parameters by sending serial instructions. The module has built-in memory, ensuring all configured parameters are saved even after power-off. G-NiceRF provides PC software free of charge for parameter configuration. The DMR858M can be connected to a computer via a USB cable or UART interface, enabling users to configure parameters using the PC software or their own device.

Diagram showing how to connect the DMR828 module to a computer via a specialized USB cable for configuration.
Figure 5.2.1: Walkie Talkie Module TTL Interface Diagram for PC connection.

5.3 DIP Switch Settings

The module includes a DIP switch for controlling key functionalities:

  • High/Low Output Power: Adjusts the transmission power.
  • Normal/Test Mode: Switches between normal operation and a test mode for diagnostics.

5.4 Volume Adjustment

A potentiometer is available on the module for adjusting the audio volume.

5.5 Push-to-Talk (PTT) Button and Microphone

The module features a PTT button for initiating transmission and a microphone input for voice communication.

6. Applications

The DMR858M module is versatile and can be integrated into a wide range of products and systems:

  • DMR walkie-talkie modules for custom devices
  • Invisible intercom systems
  • Building security systems
  • Audio surveillance systems
  • Integration into mobile phones
  • Action cameras
  • Rugged devices
  • Helmets and bicycle communication systems
  • Communication solutions for shipping and port operations
  • Door entry systems
Diagram illustrating various applications of the DMR858M module, including mobile phones, action cameras, rugged devices, helmets, bicycles, shipping/ports, and door entry systems.
Figure 6.1.1: Diverse Applications of the DMR858M Module.

7. Troubleshooting

If you encounter issues with your DMR858M module, consider the following:

  • No Power: Ensure the power supply is correctly connected to the VCC and GND pins and provides the specified voltage range (3.7V - 8.5V).
  • No Communication: Verify that the antenna is properly connected and has a 50 Ohm impedance. Check all wiring, especially for TXD/RXD, PTT, and audio connections.
  • Software Configuration Issues: Ensure the correct USB driver and PC software are installed. Double-check the serial instructions or PC software settings for channel and parameter configuration.
  • Poor Audio Quality: Inspect speaker and microphone connections. Ensure the volume potentiometer is adjusted correctly.
  • Limited Range: Confirm the antenna is suitable for the operating frequency band and is positioned optimally. Check the DIP switch for high/low power output setting.

8. Maintenance

To ensure the longevity and optimal performance of your DMR858M module, follow these maintenance guidelines:

  • Keep Dry: Protect the module from moisture and humidity.
  • Cleanliness: Keep the module free from dust and debris. Use a soft, dry cloth for cleaning.
  • Temperature: Operate and store the module within the specified operating temperature range (-20°C to 60°C). Avoid extreme temperatures.
  • Handle with Care: Avoid dropping or subjecting the module to strong impacts.
  • Antenna Care: Ensure the antenna connection is secure and the antenna itself is not damaged.

9. Warranty and Support

G-NiceRF is committed to providing high-quality IoT products, including RF modules, walkie-talkie modules, and integrated digital sensor modules. With over 10 years of experience in RF and sensor product design, G-NiceRF offers professional technical support to assist customers throughout their secondary development process.

The DMR858M module complies with RoHS and Reach standards, ensuring environmental responsibility. For any technical inquiries or support, please contact G-NiceRF directly. ODM and OEM projects are also welcomed.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.