Usongshine 17HS3401S

Contents

Usongshine Nema17 Stepper Motor 17HS3401S Instruction Manual

Model: 17HS3401S

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the Usongshine Nema17 Stepper Motor, model 17HS3401S. This 2-phase, 4-lead stepper motor is designed for precision applications such as 3D printers, CNC machines, and laser engraving machines. Please read this manual thoroughly before using the product to ensure proper function and longevity.

Five Usongshine Nema17 Stepper Motors (17HS3401S) in a set.
Figure 1: Five Usongshine Nema17 Stepper Motors (17HS3401S) in a set.

2. Product Features

  • High-Quality Construction: The motor coil is made of pure copper enameled wire, ensuring lower operating temperature, reduced deformation, and minimal noise during long-term use.
  • Precision Movement: Features a 1.8° step angle for accurate positioning.
  • Versatile Applications: Ideal for 3D printers, CNC engraving machines, laser engraving machines, and writing machines.
  • Robust Design: Incorporates international silicon steel material bearings and imported rotor rubber for durability. The textile silicon steel is oxidized to reduce surface burr after grinding.
Internal view of the motor coil and bearing, highlighting pure copper windings.
Figure 2: Internal view of the motor coil and bearing, highlighting pure copper windings.
Visual examples of applications: Laser engraving machine, 3D printer, CNC engraving machine, and writing machine.
Figure 3: Common applications for the Nema17 Stepper Motor.

3. Specifications

ParameterValue
Model Number17HS3401S
Phase2
Step Angle (degrees)1.8° ±0.09°
Rated VoltageDC 3.4V
Rated Current / Phase1.0A
Phase Resistance (20℃)2.4Ω (±15%) / Phase
Phase Inductance3.7mH (±20%) / Phase
Holding Torque≥34mN.m
Positioning Torque15mN.m (REF.)
Maximum Starting Rate≥1400 PPS
Maximum Slewing Rate≥2000 PPS
Rotating DirectionA-C B-D Clockwise
Electrical StrengthAC600V/1mA/1S
Insulation Resistance≥100 MΩ (DC 500V)
Insulation ClassB
Shaft Diameter (Options)6.35mm (With DuPont connector) or 8mm (With XH-2.54 connector)
Side view of a single Nema17 Stepper Motor, showing the model label.
Figure 4: Side view of the Nema17 Stepper Motor with model details.

4. Package Contents

Each package typically includes:

  • 5 x Usongshine Nema17 Stepper Motors (Model: 17HS3401S)
  • 5 x 4-lead connection cables (either XH-2.54 or DuPont type, depending on your selection)
Nema17 Stepper Motor with a connected 4-lead cable.
Figure 5: Stepper motor with its corresponding 4-lead connection cable.

5. Setup and Installation

Follow these steps to properly install your Nema17 Stepper Motor:

  1. Mounting: Secure the motor to your equipment using M3 screws. The motor face dimensions are approximately 42.3mm x 42.3mm, and the body length is 31mm. Ensure the mounting surface is flat and stable.
  2. Wiring: Connect the provided 4-lead cable to the motor's PH2.0-6P connector. The other end of the cable (either XH-2.54-4P or DuPont-4P) should be connected to your stepper motor driver or control board.
  3. Electrical Connection: Refer to the wiring diagram below for correct phase connections. Incorrect wiring can damage the motor or driver.
Detailed dimensional drawing, electrical schematic, and wiring diagrams for both XH-2.54 and DuPont cables.
Figure 6: Dimensional drawing and wiring diagram for Nema17 Stepper Motor 17HS3401S.

Wiring Details:

The electrical schematic shows the following connections:

  • Pin 1: Phase A
  • Pin 2: Phase C
  • Pin 3: Phase B
  • Pin 4: Phase D

Ensure these correspond to the A+, A-, B+, B- terminals on your stepper motor driver. The provided cables typically have color-coded wires (e.g., Red, Blue, Green, Black) that match these phases. Always verify with your driver's documentation.

6. Operating Instructions

To operate the Nema17 Stepper Motor, you will need a compatible stepper motor driver and a controller (e.g., Arduino, Raspberry Pi, CNC controller). The general operating principle involves sending step and direction signals to the driver, which then translates these into electrical pulses to move the motor.

  1. Connect Driver: Ensure your stepper motor driver is correctly connected to the motor and your power supply.
  2. Controller Setup: Configure your controller software to generate the appropriate step and direction signals.
  3. Micro-stepping: Utilize micro-stepping settings on your driver for smoother operation and reduced resonance, especially in precision applications.
  4. Current Setting: Set the current limit on your stepper motor driver according to the motor's rated current (1.0A per phase) to prevent overheating and ensure optimal performance.
  5. Testing: Start with slow speeds and low loads to verify correct operation before increasing speed or load.

7. Maintenance

The Usongshine Nema17 Stepper Motor is designed for durability and requires minimal maintenance. However, following these guidelines can extend its lifespan:

  • Keep Clean: Regularly clean the motor's exterior to prevent dust and debris buildup, which can affect heat dissipation.
  • Check Connections: Periodically inspect all electrical connections to ensure they are secure and free from corrosion.
  • Avoid Overheating: Ensure adequate ventilation around the motor during operation. Prolonged operation at high temperatures can reduce motor life.
  • Lubrication: The motor's bearings are typically sealed and do not require external lubrication.

8. Troubleshooting

If you encounter issues with your stepper motor, consider the following troubleshooting steps:

  • Motor Not Moving or Jittering:
    • Check all wiring connections against the diagram (Figure 6). Ensure phases are correctly connected to the driver.
    • Verify the power supply to the stepper motor driver is sufficient and stable.
    • Confirm the current setting on the driver matches the motor's rated current (1.0A).
    • Check step and direction signals from the controller.
  • Motor Overheating:
    • Reduce the current setting on the stepper motor driver if it's set too high.
    • Ensure proper ventilation.
    • Check for excessive load on the motor.
  • Loss of Steps/Inaccurate Positioning:
    • Increase the current to the motor (within its rated limit).
    • Reduce acceleration and deceleration settings in your controller software.
    • Check for mechanical binding or excessive friction in the system the motor is driving.
    • Ensure the motor is securely mounted.

9. User Tips

No specific user tips were available from reviews or Q&A for this product at this time. However, general best practices for stepper motors include:

  • Always use a dedicated stepper motor driver.
  • Properly size your power supply to meet the current demands of your motors and driver.
  • Implement micro-stepping for smoother motion and reduced noise.
  • Ensure all mechanical components connected to the motor shaft are aligned and move freely.

10. Warranty and Support

For warranty information or technical support, please contact the Usongshine Official Store directly through your purchase platform. Provide your order details and a clear description of the issue for prompt assistance.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.