MaXpeedingrods ABK-IVE614-VLC-V3-EU

Contents

MaXpeedingrods Air Suspension Spring Bag with 12V Compressor Kit User Manual

For Iveco Daily 35S 35L (2006-2014 RWD FWD)

1. Introduction

This user manual provides essential information for the safe and effective installation, operation, and maintenance of your MaXpeedingrods Air Suspension Spring Bag with 12V Compressor Kit. This kit is designed to enhance the suspension performance of Iveco Daily 35S and 35L models manufactured between 2006 and 2014, supporting both Rear-Wheel Drive (RWD) and Front-Wheel Drive (FWD) configurations. Please read this manual thoroughly before attempting any installation or operation.

2. Safety Information

Improper installation or use of this air suspension kit can lead to serious injury or damage to your vehicle. Always adhere to the following safety guidelines:

  • Professional Installation Recommended: Installation of automotive suspension components requires specialized tools and knowledge. It is highly recommended that this kit be installed by a qualified mechanic.
  • Vehicle Support: Always ensure the vehicle is properly supported on jack stands or a lift before working underneath it. Never rely solely on a jack.
  • Eye Protection: Wear appropriate eye protection during installation and maintenance.
  • Air Pressure: Handle air lines and components with care. Never exceed the maximum recommended operating pressure of 2.0 MPa (290 PSI).
  • Electrical Connections: Ensure all electrical connections for the 12V compressor are secure and properly insulated to prevent short circuits. Disconnect the vehicle's battery before working on electrical systems.
  • Component Inspection: Regularly inspect all air suspension components for wear, damage, or leaks. Replace any compromised parts immediately.
  • Children and Pets: Keep children and pets away from the work area during installation and operation.

3. Package Contents

Verify that all components listed below are present and undamaged before beginning installation.

Complete MaXpeedingrods Air Suspension Kit components including air springs, compressor, gauge, and hardware.
Figure 3.1: Overview of the complete air suspension kit components.
  • 2x Air Springs
  • 1x 12V Air Suspension Compressor
  • 1x Barometer (Pressure Gauge)
  • 4x Mounting Brackets
  • 4x Air Fittings
  • 1x Air Line (12 meters)
  • 10x Nylon Cable Ties
  • Mounting Bolts and Gaskets (various sizes)

4. Specifications

Key technical specifications for the air suspension kit:

FeatureSpecification
Model NumberABK-IVE614-VLC-V3-EU
ApplicationIveco Daily 35S, 35L (2006-2014 RWD, FWD)
Placement on VehicleRear left and right
Max. Load Capacity8800 LB / 4000 KG
Air Spring Stroke140 mm
Air Spring Max. Extended Length230 mm
Air Spring Min. Compressed Length90 mm
Air Spring Operating Pressure≤ 2.0 MPa (290 PSI)
Air Spring Temperature Range-40°C to +70°C (-40°F to 158°F)
Compressor Power150W
Compressor Output Voltage12V
Compressor Max. Current10A
Compressor Max. Working Voltage10 bar (1 MPa)
Package Dimensions74 x 27 x 20 cm
Package Weight16.3 kg
Diagram showing air spring dimensions: 140mm diameter, 88mm height, 170mm diameter at widest point, 24mm bolt length. Recommended air pressure: Min 10 PSI unloaded, 75 PSI loaded.
Figure 4.1: Air Spring Dimensions and Recommended Air Pressure.
Illustration of a 24-hour air tightness test, showing a pressure drop of less than or equal to 0.02 MPa over 24 hours.
Figure 4.2: Air Tightness Test Standard.
Close-up of the air spring material, highlighting 'Premium Natural Rubber' with a burst pressure of >= 2.0 MPa.
Figure 4.3: Air Spring Material Properties.

5. Installation

This air suspension kit is designed for a bolt-on installation, replacing the original rear suspension components. Due to the complexity and safety critical nature of suspension systems, professional installation is strongly recommended.

5.1 Pre-Installation Checks

  • Ensure the vehicle is parked on a level, stable surface.
  • Engage the parking brake and block the wheels.
  • Disconnect the vehicle's battery.
  • Verify all kit components are present and undamaged (refer to Section 3).
  • Consult your vehicle's service manual for specific instructions on removing the original rear suspension.

5.2 Air Spring Installation (Rear Left and Right)

The air springs are designed to fit the rear left and right positions. The installation process generally involves:

  1. Safely lift and support the rear of the vehicle.
  2. Remove the existing rear suspension components as per the vehicle manufacturer's guidelines.
  3. Position the new air springs with their mounting brackets onto the designated locations.
  4. Secure the air springs using the provided mounting bolts and gaskets. Ensure all fasteners are tightened to the vehicle manufacturer's specified torque settings.
  5. Connect the air fittings to the air springs.
Detailed view of an assembled air spring with mounting hardware, showing the robust construction.
Figure 5.1: Assembled Air Spring with Mounting Hardware.

5.3 12V Compressor and Air Line Installation

The 12V compressor and air lines provide the means to adjust the air pressure in the springs.

  1. Select a suitable, dry, and secure location for mounting the 12V compressor, preferably away from direct heat and moisture.
  2. Mount the compressor using appropriate fasteners.
  3. Route the 12-meter air line from the compressor to each air spring, ensuring it is protected from sharp edges, heat sources, and moving parts. Use the provided nylon cable ties to secure the air line.
  4. Connect the air line to the air fittings on the springs and the compressor.
  5. Install the barometer in a convenient location for monitoring air pressure.
  6. Connect the compressor to a 12V power source in the vehicle. It is recommended to connect it to a switched power source to prevent battery drain when the vehicle is off. Ensure proper fusing.
Image of the 12V air compressor with its electrical connections and air outlet.
Figure 5.2: 12V Air Compressor.

5.4 Post-Installation Checks

  • Reconnect the vehicle's battery.
  • Inflate the air springs to the recommended minimum pressure (10 PSI unloaded).
  • Check all air connections for leaks using a soapy water solution. Bubbles indicate a leak.
  • Lower the vehicle and perform a visual inspection to ensure proper clearance and alignment.
  • Test the system by driving the vehicle slowly and observing its handling.

6. Operation

The air suspension system allows you to adjust the rear ride height and stiffness based on load conditions. Use the 12V compressor and barometer to manage the air pressure.

  • Minimum Pressure (Unloaded): Maintain a minimum of 10 PSI (0.07 MPa) in the air springs when the vehicle is unloaded. This prevents damage to the air springs and ensures proper ride quality.
  • Maximum Pressure (Loaded): When carrying heavy loads, inflate the air springs up to 75 PSI (0.52 MPa) to restore ride height, improve stability, and prevent bottoming out. Never exceed the maximum operating pressure of 2.0 MPa (290 PSI).
  • Monitoring: Regularly check the air pressure using the installed barometer, especially before and during trips with varying loads.
  • Adjustment: Use the 12V compressor to add air and the release valve (if present on your system) to reduce air pressure as needed.

Adjusting the air pressure allows you to:

  • Maintain a level ride height when towing or carrying heavy cargo.
  • Improve vehicle stability and handling under load.
  • Reduce tire wear by maintaining proper alignment.
  • Enhance overall driving comfort.

7. Maintenance

Regular maintenance ensures the longevity and optimal performance of your air suspension system.

  • Visual Inspection: Periodically inspect the air springs, air lines, and compressor for any signs of wear, cracks, chafing, or damage. Check for loose connections or fasteners.
  • Leak Detection: Every few months, or if you notice a drop in air pressure, perform a leak test using soapy water on all air connections and the surface of the air springs. Address any leaks promptly.
  • Cleanliness: Keep the air springs and compressor free from dirt, debris, and corrosive substances. Clean with mild soap and water if necessary.
  • Air Filter (Compressor): If your compressor has an accessible air filter, inspect and clean or replace it according to the compressor's specific instructions to ensure efficient operation.
  • Pressure Monitoring: Consistently monitor air pressure to ensure it stays within the recommended range for your load conditions.
Video 7.1: MaXpeedingrods Air Suspension Testing and Manufacturing Process. This video demonstrates the rigorous testing and quality control applied to the air suspension components, highlighting their durability and air tightness.

8. Troubleshooting

This section addresses common issues you might encounter with your air suspension kit.

ProblemPossible CauseSolution
Air springs not inflating or deflating slowly.
  • Compressor not receiving power.
  • Air line kinked or blocked.
  • Air leak in the system.
  • Faulty compressor.
  • Check electrical connections and fuse for the compressor.
  • Inspect air lines for kinks or obstructions.
  • Perform a leak test (soapy water) and repair any leaks.
  • Test compressor functionality; replace if faulty.
Air springs losing pressure over time.
  • Air leak in air springs, lines, or fittings.
  • Loose connections.
  • Perform a thorough leak test and repair.
  • Tighten all air line connections.
Vehicle leaning to one side.
  • Uneven air pressure in springs.
  • Leak in one air spring or its line.
  • Check and equalize air pressure in both springs.
  • Inspect for leaks on the lower side and repair.
Compressor runs continuously or frequently.
  • Significant air leak in the system.
  • Faulty pressure switch (if applicable).
  • Locate and repair all air leaks.
  • Consult a professional for pressure switch diagnosis and replacement.

9. User Tips

  • Gradual Inflation/Deflation: When adjusting air pressure, do so gradually to allow the vehicle's suspension to settle and to avoid sudden changes in handling.
  • Cold Weather Operation: In very cold temperatures, air lines can become brittle. Exercise caution when handling and avoid sharp bends. Ensure no moisture is in the air system to prevent freezing.
  • Load Distribution: Always distribute your vehicle's load evenly to maximize the benefits of the air suspension and maintain optimal stability.
  • Regular Cleaning: Keep the exterior of the air springs clean, especially after driving in muddy or dusty conditions, to prevent abrasive wear on the rubber material.

10. Warranty and Support

This MaXpeedingrods Air Suspension Spring Bag with 12V Compressor Kit comes with a 2-year warranty from the date of purchase, covering manufacturing defects.

For technical assistance, warranty claims, or any questions regarding your product, please contact MaXpeedingrods customer support:

  • WhatsApp: +86 18374703022
  • Email: 951804521@qq.com

Please have your purchase details and product model number (ABK-IVE614-VLC-V3-EU) ready when contacting support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.