1. Introduction
This manual provides detailed instructions for the safe and efficient use of the IP2366 PD3.1 Bidirectional Fast Charging Module. This module is designed for DIY power bank applications, supporting fast charging and discharging for various battery configurations. Please read this manual thoroughly before installation and operation.
2. Product Overview
The IP2366 module is a versatile bidirectional fast charging solution, available in 140W and 280W versions, with or without a display screen. It supports 2S-6S lithium and li-iron battery packs and features multiple input/output interfaces including DC, XT60, and Type-C. The module is equipped with advanced features for power adjustment, voltage regulation, and real-time monitoring.


3. Specifications
| Feature | Description |
|---|---|
| Item Type | PCB board |
| IP Chip | IP2366 (main control), IP6557 (280W version), SW3538 (basic 280W version) |
| Power Output | 140W (PD3.1), 280W (140W+140W for 280W version) |
| Voltage Output | 28V5A (140W), 20V7A (140W), 3-21V 3A PPS |
| Battery Support | 2S-6S Lithium battery / Li-iron battery (4.2V fully charged voltage) |
| Protocols | PD3.1, QC2.0/3.0/3.0+, SCP, FCP, AFC, PPS, OCS, DCP Apple 2.4A |
| Screen | 1.14-inch TFT color display (optional), 0.96-inch color display (280W version) |
| Interfaces | DC5525, XT60, Type-C (x2 for 280W), USB-A (for 280W) |
| Cooling | Fan cooling, heat dissipation silicone, aluminum heat sink (280W version) |
| Dimensions | 5.5 cm * 7.3 cm (bare board) |
| Weight | Approx. 0.2kg (bare board) |

4. Safety Information
- DIY Product: This product is a DIY bidirectional charging module. A certain amount of basic knowledge in electronics is required for proper use. Incorrect operation may cause damage to the module or connected components.
- Battery Compatibility: Only the 280W version supports lithium iron batteries. The 140W version is primarily for lithium batteries.
- Battery Voltage: The product can only be used with lithium batteries that have a fully charged voltage of 4.2V.
- No Direct Power Source: Do NOT connect the module directly to a power source for use without a battery pack. It must be connected to a battery pack, and the battery pack needs to be connected to a protective plate.
- Protective Plate: The module itself does not come with a protective board. Ensure your battery pack has a corresponding protective board for the number of strings.
- Heat Management: When used at high power, the module can generate significant heat. It is recommended to use a cooling fan, especially for 2S/3S lithium batteries which generate more heat. A built-in fan installation port is reserved.
- Activation: After the module is connected, it needs to be charged and activated.
5. Setup Instructions
5.1. Required Components
- IP2366 PD3.1 Bidirectional Fast Charging Module
- Compatible Lithium or Li-iron battery pack (2S-6S, with protective board)
- DC connection cable (5.5 * 2.5mm, usually provided)
- Cooling fan (recommended for high-power use)
5.2. Connecting the Battery Pack
- Ensure your battery pack (2S/3S/4S/5S/6S) has a suitable protective board installed.
- Weld the provided 5.5 * 2.5mm DC cable to your battery pack.
- Connect the DC cable from the battery pack to the DC connection port on the module. The module also supports XT60 input.

5.3. Setting Battery String Count (Dial Code Usage)
Before connecting the battery pack, the number of battery strings (S) must be set using the dial switches on the module. The battery pack must also have a corresponding protection board.

- Power Adjustment: Toggle switch 1 to set the output power.
- 65W: Switch 1 UP
- 140W: Switch 1 DOWN
- Voltage Regulation: Toggle switch 2 to set the voltage regulation.
- 3.65V: Switch 2 UP
- 4.2V: Switch 2 DOWN
- Battery String (S) Settings: Use switches 3, 4, 5, and 6 to set the number of battery strings.
- 2S: Switches 3 and 4 UP simultaneously
- 3S: Switch 3 UP
- 4S: Switch 4 UP
- 5S: Switch 5 UP
- 6S: Switch 6 UP
Note: The screen orientation is upward.
5.4. Initial Activation
After connecting the battery pack and setting the string count, the module needs to be charged to activate it for the first time.
6. Operating Instructions
6.1. Charging Devices
Connect your device (laptop, mobile phone, drone, camera, etc.) to the module's Type-C or USB-A (280W version) output port. The module will automatically negotiate the appropriate fast charging protocol (PD3.1, QC, SCP, etc.) for your device.

6.2. Charging the Battery Pack (Bidirectional Function)
Connect a compatible PD3.1 power adapter to the module's Type-C input port. The module will charge the connected battery pack. The 280W version supports simultaneous charging and discharging (UPS function).
6.3. Monitor Display (with screen versions)
The 1.14-inch or 0.96-inch TFT color display shows real-time parameters such as current, voltage, and power. This allows you to easily monitor the battery level and charging/discharging status.

- When no device is connected, the display will automatically turn off and enter sleep mode to conserve power.
- The 280W version's screen is equipped with an independent coulometer for accurate battery data. The screen background can be selected (black or white), and the display direction can be adjusted.
- Use the screen refresh button (if available) to update the display.
7. Maintenance
7.1. Cooling
The module's heat dissipation is managed by its bare board properties, heat dissipation silicone, and an optional cooling fan. For high-power applications, especially with 2S/3S lithium batteries, a cooling fan is highly recommended.

- The 280W version features dual cooling with a fan and aluminum sheet. The fan operates actively, starting above 45°C and shutting down below 38°C. It activates only when a device is connected to a Type-C port.
- Ensure proper airflow around the module to prevent overheating.
7.2. Cleaning
Keep the module clean and free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquids or abrasive cleaners.
8. Troubleshooting
- Module not functioning after connection: Ensure the battery pack is correctly connected and has a protective board. Verify the battery string settings using the dial switches. The module requires initial activation by charging.
- No display on screen: If no device is connected, the screen may be in sleep mode. Connect a device or press the screen refresh button (if available).
- Slow charging/discharging: Check the power adjustment dial switch (65W/140W). Ensure your power source and connected device support the desired fast charging protocols.
- Excessive heat: Ensure a cooling fan is installed and functioning, especially for high-power use or with 2S/3S lithium batteries. Verify proper ventilation.
- Inaccurate screen readings (280W version): The 280W version has an independent coulometer for accuracy. If readings seem off, ensure all connections are secure.
9. User Tips
- Always double-check the dial switch settings for battery string count and power output before connecting the battery pack to avoid damage.
- For optimal performance and longevity, consider using a robust enclosure for the module, especially if it's a bare board version.
- When using the 280W version, take advantage of the dual Type-C ports for simultaneous high-power charging/discharging.
10. Warranty and Support
This product is a DIY module. For specific warranty information, please refer to the seller's terms at the time of purchase. For technical support or if you encounter issues not covered in this manual, please contact the seller directly.