BAJETON BJ-8300

Contents

BAJETON BJ-8300 Multi-Band Walkie Talkie User Manual

Model: BJ-8300 | Brand: BAJETON

1. Introduction

The BAJETON BJ-8300 is a versatile multi-band walkie talkie designed for a wide range of communication needs. It features shortwave (SW), AM, SSB, CB reception, wireless Bluetooth phone programming, NOAA weather channels, and intelligent noise reduction. This manual provides detailed instructions for setting up, operating, and maintaining your device to ensure optimal performance.

Important Note: We sincerely apologize for the issue where the LSB and USB programs were reversed in a previous batch of walkie-talkies. This issue has been fixed. If your product has this problem, please download a firmware update from www.binteradio.com. Please do not use firmware from other brands, as this may cause damage to the product.

2. Safety Information

  • Always use the correct antenna for the desired frequency range. Using an incompatible antenna can damage the device or result in poor performance.
  • Do not expose the device to extreme temperatures, direct sunlight for prolonged periods, or corrosive substances.
  • Keep the device away from water and moisture unless explicitly stated as waterproof. This model is not waterproof/water-resistant.
  • Only use the provided charger and battery or approved replacements.
  • Do not attempt to disassemble or modify the device. Repairs should only be performed by authorized personnel.
  • Ensure proper ventilation when charging to prevent overheating.

3. Package Contents

The standard package for your BAJETON BJ-8300 Walkie Talkie includes the following items:

BAJETON BJ-8300 Walkie Talkie and its accessories: Antenna, Battery, Charger, Clip, Type-C Charger, Lanyard, Manual.

Image: Standard package contents for the BAJETON BJ-8300.

  • BAJETON BJ-8300 Radio Unit
  • Antenna
  • Battery
  • Charger (Wall Adapter)
  • Belt Clip
  • Type-C Charging Cable
  • Lanyard
  • User Manual (this document)

4. Getting to Know Your Device (Setup)

4.1 Device Layout

Familiarize yourself with the various parts of your walkie talkie:

Front view of BAJETON BJ-8300 Walkie Talkie showing display, keypad, and controls. Inset shows Bluetooth Phone Programming feature and frequency ranges.

Image: Front view of the BAJETON BJ-8300 Walkie Talkie with key features highlighted.

  • Power Knob: Top right, for turning on/off and volume control.
  • Indicator Light: Near the power knob, indicates status (e.g., charging, transmitting).
  • Antenna Connector: Top left, for attaching the antenna.
  • Display Screen: Front, shows frequency, channel, and other information.
  • Microphone Jack: Side, for external microphone.
  • Headphone Jack: Side, for headphones.
  • Analog PTT: Side button for Push-To-Talk.
  • PF2/PF3: Programmable function keys.
  • Number Keypad: For entering frequencies and menu selections.
  • Type-C Charging Port: Bottom, for charging the device.

4.2 Antenna Connection

Proper antenna connection is crucial for optimal performance. The BJ-8300 features both SMA-Male and SMA-Female interfaces for different antenna types.

Close-up of the top of the walkie talkie showing SMA-Female and SMA-Male antenna interfaces.

Image: Antenna interfaces on the top of the walkie talkie.

  • 16-65 MHz Receiving Channel: Compatible with the SMA-Male interface antenna to enhance the performance of received signals.
  • Multi-Band Signal Reception & Transmission: The original antenna has a frequency range of FM/136-174/400-470MHz. If you need to use frequencies beyond this range, you must purchase a dedicated SMA-Female antenna. Different frequency ranges require antennas compatible with the corresponding frequencies (e.g., a 27MHz CB antenna for 27MHz).

4.3 Battery Installation and Charging

The BJ-8300 uses a rechargeable battery and supports convenient Type-C charging.

Diagram showing Type-C charging options: Wall Charging, Car Charging, Computer Charging, and Power Bank Charging.

Image: Various methods for Type-C charging the walkie talkie.

  1. Dock Charging (Optional): Insert the battery pack or the radio with the battery pack into the charging dock. Ensure proper contact with the charging terminals of the dock.
  2. Type-C Charging: Connect the provided charging cable to the power adapter and plug the power adapter into an AC power outlet. Insert the charging cable into the Type-C interface of the main unit's battery.
  3. Charging Indicator: When the device is charging, the red indicator light indicates charging in progress. The green indicator light indicates charging is complete.

5. Operating Instructions

5.1 Basic Operations

  • Main Frequency Band Selection: On the standby screen, short press the (A/B) key or long press the (EXIT) key to select the main frequency. The larger display indicates the currently active main frequency band.
  • PTT Function: When operating on the A band, press the PTT key to transmit on the A band frequency. When operating on the B band, press the PTT key to transmit on the B band frequency.
  • Channel Mode and Frequency Mode Switch: Short press the 【VFO/MR】 key or long press the 【OK】 key button to switch between channel mode and frequency mode.
  • AM Air Band Mode: Short press the 【VFO/MR】 key or long press the 【OK】 key to switch to frequency mode. Directly input the air band frequency within the range of 108 MHz to 136 MHz. The radio will automatically enter AM reception mode, and the channel status will display AM. This mode is primarily used to receive AM modulated signals.
  • Scanning Mode: Assign the scanning function to the side keys PF2/PF3, or long press button 1 to start frequency or channel scanning. You can choose one of the following modes from Menu 23:
    • Time Operation Mode (TO): When the walkie-talkie detects a signal, it stops scanning and stays at the same frequency. After 5 seconds, it will resume scanning, even if the signal is still present.
    • Carrier Operation Mode (CO): The walkie-talkie stops scanning and remains at the same frequency when it detects a signal, until the signal disappears. There is a 2-second delay before scanning resumes after the signal is lost.
    • Search Operation Mode (SE): Upon detecting a signal, the walkie-talkie exits the scan and stays on this frequency.
  • Commercial FM Radio Broadcast Reception Functions (Long Press Button 0): Long press the button 0 to turn on the FM RADIO; the screen will display the current frequency. Use the UP/DOWN keys or the channel knob to adjust the frequency. You can also input a frequency directly via the keypad.

5.2 Advanced Features

  • Shortwave Interface: After setting the PF2 side key as the shortcut to enter shortwave, press PF2 briefly to access the shortwave interface. Press and hold 【0】 to enter the shortwave interface. In the shortwave interface, briefly press 【*】 to switch STEP/BW/LAN/BFO.
  • Video: Demonstrates setting PF2 side key as a shortcut to enter shortwave and navigating the shortwave interface.

  • Super Mode: The factory setting is in super mode. If there are frequency restrictions in your region, you can turn it off.
    • Turn On Super Mode: Press PTT key + "8" key + Turn on.
    • Turn Off Super Mode (Factory Mode): Press PTT key + "EXIT" key + Turn on.
    Diagram showing how to turn on and turn off Super Mode, along with the frequency ranges for Super Mode and Factory Mode.

    Image: Instructions for activating and deactivating Super Mode, and associated frequency ranges.

    Super Mode Frequency Range: 18-108MHz (TX/RX), 108-136MHz (RX), 136-580MHz (TX/RX), 760-999MHz (TX/RX).

    Factory Mode Frequency Range (without Super Mode): 18-108MHz (RX), 108-136MHz (RX), 136-174MHz (TX/RX), 174-200MHz (RX), 200-260MHz (TX/RX), 260-330MHz (RX), 330-520MHz (TX/RX).

  • Bluetooth Phone Programming: This feature allows you to program your walkie talkie wirelessly using a smartphone app.
    1. Download App: Scan the QR code for iOS or Android to download the programming application. QR codes for downloading the Bluetooth Programming App for iOS and Android.

      Image: QR codes for downloading the Bluetooth Programming App.

    2. Connect Device: Connect the walkie talkie with your phone via Bluetooth.
    3. Select Model: In the app, select model BJ-8300 and read data from the radio.
    4. Modify & Write: Modify the desired data (e.g., frequencies, channel names) and write it back to the radio.
    Screenshot of the phone app for wireless programming, showing channel information and settings.

    Image: Phone APP interface for wireless programming.

  • Intelligent Noise Reduction: This feature ensures clear voice communication even in noisy environments. Walkie talkie displaying 'Multi Band' with sound waves indicating noise reduction.

    Image: Visual representation of Intelligent Noise Reduction.

  • Spectrum Analyzer Function: Provides rich spectrum information and analysis functions to solve signal interference problems and improve communication quality. Walkie talkie next to professional spectrum analyzer equipment, illustrating its spectrum analyzer function.

    Image: The walkie talkie's spectrum analyzer function compared to professional equipment.

  • Wireless Copy Frequency: Allows for easy and fast replication of frequencies between devices, eliminating complex computer programming and reducing manual programming errors. Two walkie talkies, one with a display showing frequency, illustrating wireless copy frequency feature.

    Image: Wireless Copy Frequency in action.

  • PF2, PF3 Custom Buttons: Support a variety of functional options, providing convenience and efficiency. Diagram showing various functions that can be assigned to PF2 and PF3 custom buttons, such as FM, TX Power, Scan, Search, NOAA, SOS, Lamp.

    Image: Customizable functions for PF2 and PF3 buttons.

  • DTMF Encode Sending:
    • Fast Operation: Press and hold the PTT button while entering the number keys 0-9, MENU, UP, DOWN, EXIT, *, and #. The radio will transmit DTMF codes 0-9, A, B, C, D, *, and #. Release the button to stop sending codes.
    • Editing DTMF Code: In standby mode, short press the 【#】 button to enter the DTMF code editing interface. You can enter codes 0-9, OK, UP, DOWN, Exit, *, and # via the keypad. Press PTT to send the DTMF code.
  • PTT-ID Function: Transmit identity codes or call codes via DTMF. There are 15 sets of call codes, configurable through "Programming Software → Edit → DTMF". Each signal or A/B band can independently select the call code group to be sent. Configure identity code parameters via "Programming Software → Edit → DTMF → Local ID Code". There are three transmission methods:
    • Send on Press: After pressing the PTT, the call code/identity code is sent first, followed by the voice signal.
    • Send on Release: After releasing the PTT, the call code/identity code is sent, then the transmission ends.
    • Send Both: The call code/identity code is sent both when the PTT is pressed and released.

    Note: Since the identity code operation is independent of the call code, if there is a conflict between the identity code and the call code settings, the identity code will be sent.

  • Weather Forecast NOAA Function: Press the designated side key (if configured as NOAA from Menu 24-26) to activate this function. The radio has 10 built-in fixed frequencies. You can press the UP/DOWN keys to select the frequency you want to listen to. Note: The NOAA weather forecast function is available only in countries and regions that support the NOAA channels.

5.3 Menu Function List

The following tables detail the available menu options and their settings:

Shortcut Keys Combination
ActionFunction
Long press number 1Enter scanning function
Long press number 2Store frequency into channel
Long press number 3Set frequency step
Long press number 4Select High, Middle, Low power
Long press number 5Adjust squelch levels
Long press number 6Turn on/off dual standby
Long press number 7Set CTCSS sub tone
Long press number 8Set repeater shift direction
Long press number 9Set repeater offset frequency
Long press number 0Turn on FM Radio broadcast
Long press number #Lock/Unlock keypad
Short press number #DTMF tone edit
Short press number *Switch R/T
Menu Function List (Part 1)
No.MenuSecond MenuSetting
0SQL0,...,9Setting the squelch to off will open up the squelch entirely. Squelch silences the receiver when there is no signal. The lower level is easier to interfere, and in the higher level, the sensitivity is not as good as lower level, so it is best to set it to middle.
1STEP2.5K, 5.0K, 6.25K, 8.33K, 10.0K, 12.50K, 20.0K, 25.0K, 50.0KIn frequency mode, press the up and down keys to change the step of the frequency. Selects the amount of frequency change in VFO/frequency mode when scan or press UP/DOWN keys.
2TXPHigh, Middle, LowTransmit at High, Middle, Low power.
3SAVEOFF, 1:1, 2:1, 3:1Power save disable. Selects the ratio of sleep cycles to awake cycles (1:1, 2:1, 3:1). The higher the number, the longer battery lasts. The higher number increases the RX sleep cycle, but you may miss the first few syllables before the RX opens.
4VOXOFF, 1,2,...,9Disable Voice Transmit function. Activate the VOX function, level 1 is most sensitivity. When enabled, it is not necessary to push the PTT button.
5W/NWIDE, NARROWWideband (25Khz bandwidth). Narrowband (12.5Khz bandwidth).
6ABR5sec,...,3min, OFFBacklight auto switch off time. Backlight is always ON.
7TDROFF, ONDual frequency standby OFF/ON.
8PROMPTOFF, ONOperate beep OFF/ON, Allows audible confirmation of a key press.
Menu Function List (Part 2)
No.MenuSecond MenuSetting
9TOTOFF, 15S...75STime out timer for transmit. This feature provides a safety switch that limits transmission time to a programmed value.
10ZONEZONE 1,...,ZONE 15Operation to change ZONE.
11MEMCHCH-001,...,064Used to create new channels (0 through 256) so that they can be accessed from MR/Channel mode. If the Icon "CH-" is displayed, the channel is already stored.
12DELCHCH-001,...,064Delete a stored channel. If there is no CH in the front, the channel has no parameters and the operation is invalid.
13R-CTCSSOFF, 67.0HZ,...,254.1HZNone CTCSS. Receive Standard CTCSS. Select standard tone or input non-standard tone via keypad.
14R-DCSOFF, D023N,...,D7541None DCS. Receive Standard DCS. Select standard tone or input non-standard tone via keypad.
15T-CTCSSOFF, 67.0Hz,...,254.1HzNone CTCSS. Transmit Standard CTCSS. Select standard tone or input non-standard tone via keypad.
16T-DCSOFF, D023N,...,D7541None DCS. Transmit Standard DCS. Select standard tone or input non-standard tone via keypad.
Menu Function List (Part 3)
No.MenuSecond MenuSetting
17VOICEPRIOFF, Encryption 1, Encryption 2, Encryption 3Subtone encryption. If enabled, others can't hear if their frequency and CTCSS/DCS is same as yours.
18CH-NAMEChannel NameInput channel name, press # to switch input method.
19ROGEROFF, BEEPDisable/Enable. Sends an end-of-transmission tone to indicate to other stations that the transmission has ended.
20VOICEOFF, ON, ENGLISH, русскийVoice prompts OFF/ON. Allow audible voice confirmation of a key press. Voice guide in English/русский.
21LANGUAGEENGLISH, русскийSets the voice guide language.
22BCLOFF, ONBusy channel lockout OFF/ON. Disable the PTT button on a channel that is already in use.
23SC-REVTO, CO, SETime scanning (TO): When the radio detects a signal, it pauses scanning and remains for about 5 seconds. Carrier scanning (CO): When it detects a signal, the radio stops scanning and remains at the scanned frequency. Search scanning (SE): When the walkie talkie detects a signal, it exits the scan and remains at this frequency.
24PF2SPECTRUM/RADIO/SOS/TXPOWER/SCAN/SEARCH/NOAA/PTTBAllows you to assign the function you want as a shortcut to the radio PF2 keys. This corresponds to short press.
Menu Function List (Part 4)
No.MenuSecond MenuSetting
25PF2 LONG PRESSSOS/SPECTRUM/RADIO/TXPOWER/SCAN/SEARCH/NOAAAllows you to assign the function you want as a shortcut to the radio PF2 keys. This corresponds to long press.
26PF3SOS/SPECTRUM/RADIO/TXPOWER/SCAN/SEARCH/NOAAAllows you to assign the function you want as a shortcut to the radio PF3 keys. This corresponds to short press.
27OFFSET0Frequency difference between radio transmission and reception.
28SFT-DOFF, +, -Enable access of repeater mode, OFF: None repeater shift. In frequency mode, the TX frequency equals the RX frequency plus/minus the frequency difference.
29POWERON MSG, LOGO, OFFPower on show message, logo, or off.
30S-CODE1,2,3...15DTMF Signal codes.
31DTMF CODEOFF, BOT, EOT, BOTHTransmit DTMF code when press PTT (BOT), when release PTT (EOT), or both.
32DTMFSTOFF, DT-STWhen transmitting (press PTT), Type DTMF code, radio will not emit the sound code (OFF) or will emit the sound code (DT-ST).
Menu Function List (Part 5)
No.MenuSecond MenuSetting
33AUTOLOCKOFF, 5S, 10S, 15SKeypad lock turn off. Time to auto keypad lock.
34SCAN ADDADD/DeleteAdd or delete the channels into scan list.
35TONE1000Hz, 1450Hz, 1750Hz, 2100HzTo send out a burst tone, you simultaneously press PF2 key while holding down the PTT.
36PTT-LT0, 100,...,1000MsDelay time before automatic DTMF transmitting.
37MENU TIME5, 10,...,60secDuring the menu operation, the delay time for exiting due to no operation.
38VOX DELAY0.5sec,...,2.0secVOX delay time.
39RP-STEOFF, 100ms,...,1000msThis function is used to eliminate squelch tail noise when communicating through a repeater. Delay the tail tone of repeater (1-10s).
40RPT-RLOFF, VOLTAGE, NAME, FREQ, CHShow voltage, name, frequency, or channel number.
41MDF-ANAME, FREQ, CHA BAND show frequency, channel number, or channel name.
42MDF-BNAME, FREQ, CHB BAND show frequency, channel number, or channel name.
43TX-A/BOFF, A, BIn dual standby mode, press PTT to transmit in Main Band (OFF), in A Band (A), or in B Band (B).
Menu Function List (Part 6)
No.MenuSecond MenuSetting
44STEOFF, ONSquelch tail noise eliminate set OFF/ON. This function is used to eliminate squelch tail noise between our handhelds that are communicating directly (no via repeater).
45AL-MODON SITE, SEND SOUND, SEND CODEField alarm. Send alarm sound. Send alarm tone.
46SCRAMBLEOFF/ONVoice scrambler function. Provide two scrambler frequency, prevent parties on other radios at same frequency from hearing and understand your voice.
47NOISE REDUCTIONOFF/ONOption function, Turn on Noise Reduction/Cancellation.
48BLUETOOTHOFF/ONOption function, Turn on Bluetooth connect with mobile app. RT-900 bluetooth version only.
49RESETVFO, ALLMenu initialization.
50ModulationRX, FM, AMSwitch between AM modulation or FM modulation.
51VERSIONFirmware, HardwareShow firmware version number. Show Hardware version number.

6. Specifications

AttributeValue
Brand NameBAJETON
Model NumberBJ-8300
Walkie Talkie TypePortable
Output Power(w)5w-10w
Maximum Range5km-10km
Frequency Range108-136mhz, 2.3-30Mhz, 220-260 MHz, 27Mhz, 300-390MHz, 400-520MHz, 520-1710Khz, 65-108mhz, 136-174 MHz
Shortwave frequency2.3-30MHz
Medium wave frequency520-1710KHz
Long wave frequency153-279KHz
MaterialABS
Is_DisplayYes
Waterproof / Water-ResistantNo
Battery IncludedYes
Feature 1Phone Programming
Feature 2Intelligent Noise Reduction
Feature 3PF2, PF3 Custom Keys
Feature 4Type-C Charging
Feature 5NOAA weather forecast channels
Useothers
High-concerned chemicalNone
OriginMainland China

7. Maintenance

To ensure optimal performance and extend the lifespan of this product, please follow these guidelines:

7.1 Daily Maintenance

  • Do not pierce or scratch the product with hard objects.
  • Do not store the product in environments containing chemical corrosive substances.
  • Do not carry or use the product by pulling the earphone cable.
  • When not using the earphone jack, cover the interface with the protective cap.

7.2 Cleaning Procedure

Before cleaning, please power off the device and remove the battery:

  1. Regularly use a dry, clean, lint-free cloth or a soft brush to remove dust from the product surface and charging terminals.
  2. If the buttons or casing become dirty, use a neutral detergent and a non-woven cloth for cleaning. Do not use detergents, alcohol, sprays, or petroleum-based chemicals as they may damage the surface casing.
  3. After cleaning, ensure the product is completely dry before use.

8. Troubleshooting

  • LSB/USB Reversal: If you experience LSB and USB programs being reversed, download and install the latest firmware update from www.binteradio.com.
  • Programming Issues: If Bluetooth programming is inconsistent, try using a programming cable. For CHIRP software, enable "developer mode" and add the DT-920 module.
  • Frequency Step Not Changing: If the frequency step doesn't change after applying settings in the menu, consult the full user manual (PDF) for more detailed instructions or contact support.
  • Radio Not Functioning After Firmware Update: Ensure you only use official BAJETON firmware. Using firmware from other brands can damage the product.

9. User Tips

  • The BJ-8300 offers good reception on 40m LSB and works well with a small SW blue loop antenna when tuned correctly.
  • The radio features 960 channels on the main tuner, excellent AM airband performance, a large battery, and 15 LW/MW, 15 SW, and 15 AM broadcast channels on the second SI4732 derived tuner.
  • Super Mode allows for a wide frequency range of 18MHz to 1GHz without the need for firmware flashing.
  • Official CPS programming software is available at www.binteradio.com under the downloads section. If the download doesn't start immediately, try the link again.
  • While Bluetooth programming is convenient, some users find cable programming more reliable.
  • The radio can receive AM Airband frequencies (108-136 MHz).
  • It can transmit and receive in the 27MHz band, as its TX/RX range includes 18-108 MHz and 136-580 MHz.
  • The device supports both AM and SSB (Shortwave Modulation) transmission.

10. Warranty Information

The warranty period for this product starts from the date of sale (based on the date on the sales invoice). The main unit is covered for 12 months, and the battery and charging accessories are covered for 6 months. The following cases will require paid repair services during the warranty period:

  • Failure to present this warranty card and the purchase invoice.
  • This card shows signs of alteration or does not match the product.
  • Defects and damages caused by using this product under non-standard conditions.
  • Defects and damages caused by misuse, accidents, water ingress, or negligence.
  • Defects and damages resulting from improper testing, operation, repair, installation, modification, or adjustment.
  • Defects and damages caused by unauthorized repairs or disassembly.
  • Defects and damages caused by force majeure.
  • Normal wear and tear from regular use.

This warranty card serves as an important proof for the end user to enjoy warranty services. It must be stamped and filled out completely by an authorized dealer to be valid. Please keep it safe.

11. Additional Resources

For a more detailed user manual in PDF format, please refer to the official document:

View User Manual (PDF)


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.