SCULPFUN Automatic Air Assist Kit

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the SCULPFUN Automatic Air Assist Kit. This kit is designed to upgrade SCULPFUN S9 and S10 laser engraving machines to an automatic air assist system, similar to the S30 series. It includes a 32-bit automatic air assist mainboard, a 30L/min automatic air pump, a 12V/7A power adapter, and an installation kit. The system allows for intelligent control of air assist during laser cutting and engraving operations, compatible with LightBurn software's M8 air assist switch.

2. Safety Information

Please read and understand all safety warnings and instructions before installing and operating this product. Failure to follow these instructions may result in injury or damage to the equipment.

• Always wear appropriate personal protective equipment, including laser safety glasses, when operating a laser engraver.
• Ensure the laser engraver is turned off and unplugged before performing any installation or maintenance.
• Do not operate the air pump or laser engraver in wet conditions or near flammable materials.
• Keep children and pets away from the work area.
• Ensure proper ventilation in the work area to dissipate fumes and debris generated during engraving/cutting.
• Verify the power adapter voltage (12V/7A) matches the requirements of your laser engraver and air pump.
• Do not modify the components of this kit. Use only original or approved replacement parts.

3. Package Contents

Verify that all items listed below are included in your package:

• 1 x 32-bit Automatic Air Assist Main Board + Installation Box
• 1 x 12V DC Air Pump (30L/min)
• 1 x 12V/7A Power Adapter
• 1 x Installation Kit (including screws, wrench, cable ties, etc.)

4. Specifications

5. Setup and Installation

Follow these steps to install the Automatic Air Assist Kit onto your SCULPFUN S9 or S10 laser engraver.

1. Prepare the Engraver: Ensure your laser engraver is powered off and unplugged from the power source.
2. Install the 32-bit Main Board:
   • Carefully remove the existing main board from your S9/S10 engraver.
   • Install the new 32-bit automatic air assist main board into the provided installation box.
   • Mount the installation box onto your engraver using the supplied screws and wrench. Refer to Figure 5.1 for visual guidance on mounting points.

   

3. Connect the Air Pump:
   • Connect the 12V DC air pump to the designated air assist interface on the new main board.
   • Secure the air hose from the air pump to the air nozzle on your laser module. Ensure a snug fit to prevent air leakage.

   

   

4. Connect Power: Connect the 12V/7A power adapter to the main board and then plug it into a suitable power outlet.
5. Verify Upgrade: Your S9 or S10 engraver is now upgraded with the automatic air assist system.

Examples of upgraded machines:

6. Operating Instructions

The automatic air assist system is designed to be controlled via software, specifically using the M8 air assist switch in LightBurn.

1. Software Control (LightBurn M8):
   • The 32-bit main board is compatible with LightBurn software.
   • For cutting operations, enable the M8 air assist switch in LightBurn. This will automatically turn on the air pump, providing airflow to prevent yellowing and improve cut quality.
   • For engraving operations, disable the M8 air assist switch in LightBurn. This will automatically turn off the air pump, which is typically preferred for finer engraving details where air assist might cause blurring or excessive material removal.

   

2. Adjusting Air Pump Flow Rate:
   • The air pump features a speed control design.
   • You can adjust the airflow rate from 0-30L/min by rotating the regulator on the air pump unit.
   • Adjust the airflow according to the specific material and desired engraving/cutting results.

   

7. Maintenance

Regular maintenance ensures optimal performance and longevity of your Air Assist Kit.

• Cleaning: Periodically clean the air pump and air hose to prevent dust and debris buildup. Use a soft, dry cloth. Do not use harsh chemicals or abrasive materials.
• Connections: Regularly check all electrical and air hose connections to ensure they are secure and free from damage.
• Air Filter (if applicable): If your air pump model includes an air filter, inspect and clean or replace it as recommended by the manufacturer to maintain optimal airflow.
• Storage: When not in use for extended periods, store the kit in a clean, dry environment away from direct sunlight and extreme temperatures.

8. Troubleshooting

If you encounter issues with your Air Assist Kit, refer to the following common problems and solutions:

• Air pump not turning on:
  • Check if the power adapter is securely connected to the main board and a working power outlet.
  • Ensure the main board's power switch (if present) is in the 'ON' position.
  • Verify that the M8 air assist command is correctly enabled in your LightBurn software for the current operation.
  • Inspect the wiring between the air pump and the main board for any loose or damaged connections.
• Weak or no airflow:
  • Check the air hose for kinks, blockages, or leaks.
  • Ensure the air pump's flow rate regulator is adjusted to an appropriate setting.
  • Clean any potential blockages in the air nozzle on the laser module.
  • If applicable, check and clean the air filter on the pump.
• Air assist not responding to LightBurn M8 command:
  • Confirm that the 32-bit main board is correctly installed and recognized by your laser engraver's firmware.
  • Ensure your LightBurn software is configured to send M8 commands for air assist control.
  • Check for any firmware updates for your laser engraver that might affect air assist functionality.

9. User Tips

• For optimal cutting results, experiment with different air assist flow rates and laser power settings on various materials.
• When engraving delicate materials, consider turning off air assist or using a very low flow rate to avoid scattering fine debris or affecting detail.
• Regularly clean your laser lens and air nozzle, as air assist can sometimes push debris onto these components.

10. Warranty and Support

The SCULPFUN Automatic Air Assist Kit comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please contact our customer service:

• WhatsApp: +86 16633953613
• Email: jinpin13@126.com