1. Safety Information
Please observe the following safety precautions to prevent damage to the device or injury to yourself:
- Do not expose the device to extreme temperatures (outside 8°C to 50°C / 46°F to 122°F), direct sunlight, or high humidity.
- Use only a standard 5V DC/≥1A power supply for charging. Avoid fast chargers.
- Ensure proper ventilation around the device during operation.
- Do not attempt to disassemble or modify the device beyond user-replaceable components (tubes, op-amps).
- Keep out of reach of children.
- If the device will not be used for an extended period, remove the batteries.
2. Package Contents
Verify that all items are present in your package:
- 1x P10-PRO Headphone Amplifier
- 1x 3.5mm Audio Cable
- 1x Type-C Charging Cable
- 2x Rubber Bands
- 1x Screwdriver
- 1x User Manual (this document, or a printed version)
3. Product Overview
The Douk Audio P10 PRO is a portable HiFi tube headphone amplifier designed to deliver rich, warm audio. It features a hybrid vacuum tube and op-amp design, offering customizable sound through swappable components.
Key Components:
- Power On/Off/Volume Knob: Controls power and audio output level.
- 3.5mm AUX Input: Connect your audio source (e.g., phone, laptop).
- 3.5mm Headphone Output (TRS): Connect your headphones.
- JAN6148 Tubes (Swappable): Provides the characteristic tube sound.
- NE5532 Op-amp (Swappable): Amplifies the audio signal.
- Type-C Power Interface (DC 5V/≥1A): For charging the internal batteries.
- Battery Level Indicators: Shows the current battery charge status.
- Charging Indicator: Red indicates charging, Blue indicates fully charged.
4. Setup
4.1 Battery Installation and Charging
The P10 PRO uses two 14500 Li-ion batteries (3.7V, 600mAh each). Ensure batteries are correctly inserted according to polarity markings. The device supports charging while listening.
- Open the battery compartment (if applicable, typically by removing the top cover with the provided screwdriver).
- Insert two 14500 Li-ion batteries, ensuring correct polarity. Always use two batteries of the same brand, model, and capacity.
- Close the battery compartment.
- Connect the Type-C charging cable to the device's Type-C power interface and to a standard 5V DC/≥1A power adapter.
- The charging indicator will be red during charging and turn blue when fully charged. A full charge takes approximately 2.5-3 hours when powered off.
4.2 Connecting Audio Devices
- Connect your audio source (e.g., smartphone, tablet, computer) to the P10 PRO's 3.5mm AUX input using the provided 3.5mm audio cable.
- Connect your headphones to the P10 PRO's 3.5mm headphone output (TRS).
5. Operating Instructions
5.1 Powering On/Off and Volume Control
- To power on the device, rotate the Power On/Off/Volume knob clockwise until you hear a click and the tubes glow.
- To adjust the volume, continue rotating the knob clockwise to increase volume or counter-clockwise to decrease volume.
- To power off the device, rotate the knob counter-clockwise until you hear a click.
5.2 Battery Level Indicators
The P10 PRO features a 5-level battery indicator display (0% / 25% / 50% / 75% / 100%). These indicators will light up for approximately 3 seconds after power-on and then turn off automatically during use to conserve power. They will reactivate upon the next power-on cycle.
5.3 Video Guide
6. Maintenance
6.1 Tube Replacement
The P10 PRO allows for tube rolling to customize your sound. The default tubes are Raytheon JAN6418. Compatible replacement tubes include CK6418 or CK548DX.
- Ensure the device is powered off and disconnected from any power source.
- Carefully remove the top cover using the provided screwdriver.
- Gently pull out the existing tubes. If there is glue on the tube pins, carefully remove it before replacement.
- Insert the new compatible tubes, ensuring they are seated correctly.
- Replace the top cover.
6.2 Op-Amp Replacement
The op-amp can also be upgraded for different sound characteristics. The default op-amp is NE5532. Compatible dual op-amps include JRC4558, JRC4556, OPA2604, OPA2111, or MUSES02.
- Ensure the device is powered off and disconnected from any power source.
- Carefully remove the top cover using the provided screwdriver.
- Using appropriate tools (e.g., IC extractor or small flat-head screwdriver), gently pry out the existing op-amp from its socket.
- Align the new op-amp correctly with the socket (note the orientation notch) and gently press it into place.
- Replace the top cover.
6.3 General Care
- Clean the device with a soft, dry cloth. Do not use liquid cleaners.
- Store the device in a cool, dry place when not in use.
- If storing for a long period, remove the batteries.
7. Troubleshooting (FAQ)
- Q: Why does the P10-PRO make a noise when powered on/off or shocked?
- A: JAN6418 are directly heated tubes. During power-on/off or physical shock/tap/vibration, a "wing~~~" noise may occur for 25-35 seconds. This is normal and will fade as the tube stabilizes.
- Q: Why did the battery indicators turn off after I turned the P10-PRO on?
- A: This is normal. The battery indicators are designed to automatically turn off about 3 seconds after power-on and remain off during use. They will only light up again upon the next power-on.
- Q: What kind of charger should I use?
- A: Please use a standard 5V DC power supply (≥1A). Avoid fast chargers to prevent damage.
- Q: Can I replace the batteries with different brands or models?
- A: No. Always use two batteries of the same brand, model, and capacity to avoid malfunctions or safety risks.
- Q: Is there a temperature requirement for use?
- A: The recommended working temperature is 8°C to 50°C (46°F to 122°F). Avoid extreme temperatures to ensure proper charging and performance.
- Q: If I won’t use the P10-PRO for a while, should I remove the batteries?
- A: Yes, it is recommended to remove the batteries for long-term storage.
- Q: Can I replace the tubes?
- A: Yes. The default Raytheon JAN6418 tubes can be replaced with CK6418 or CK548DX. Remember to remove any glue from the pins before replacement.
- Q: Can I upgrade the op-amp?
- A: Yes. The default NE5532 can be upgraded to dual op-amps like JRC4558, JRC4556, OPA2604, OPA2111, or MUSES02.
8. Specifications
| Parameter | Value |
|---|---|
| Brand | Nobsound (Douk Audio) |
| Model | P10-PRO |
| Audio Input | 3.5mm AUX |
| Audio Output | 3.5mm Headphone Jack |
| Output Power | 170mW@32Ω |
| Frequency Response | 20Hz-20KHz |
| THD | <0.1% |
| SNR | 75dB |
| Gain | 12dB |
| Max. Input Level | 1.0Vrms |
| Max. Output Level | 2.5Vrms |
| Matched Headphone Impedance | 16-200Ω |
| Working Mode | Vacuum Tube + Op-amp Hybrid |
| Power Supply | 2 × 14500 Li-ion batteries (3.7V, 600mAh each, total 1200mAh) |
| Battery Life | 8–10 hours (varies with volume level used) |
| Battery Indicator Display | 5-level (0% / 25% / 50% / 75% / 100%) |
| Working Temperature | 8-50℃ |
| Input Voltage | DC 5V/≥1A |
| Dimensions (W*D*H) | 120*75*18mm / 4.72*2.95*0.71in |
| Net Weight | 252g / 0.55lb |
| Package Weight | 400g / 0.88lb |
9. User Tips
- Tube Rolling: Experiment with different compatible tubes (CK6418, CK548DX) to find the sound signature that best suits your preferences. Remember to remove any glue from the pins before replacement.
- Op-Amp Rolling: Customize your audio further by swapping the op-amp with compatible models like JRC4558, JRC4556, OPA2604, OPA2111, or MUSES02.
- Battery Management: For optimal battery life and safety, always use two identical 14500 Li-ion batteries. If you plan not to use the amplifier for an extended period, remove the batteries.
- Charging Flexibility: The P10 PRO allows for continuous music playback even while charging, offering convenience for longer listening sessions.
- Visual Enjoyment: Take advantage of the visible top window to admire the warm glow of the tubes, adding an aesthetic dimension to your listening experience.
10. Warranty and Support
The Douk Audio P10 PRO comes with a 2-year warranty, ensuring quality and reliability.
For further assistance or detailed information, please refer to the official user manual available in PDF format: Download User Manual (PDF).