CHANTOWER Pure Sine Wave Inverter 1000W 1600W 2200W 3000W 4000W 5000W

Contents

Intelligent Power Inverter User Manual

Operation Instructions for CHANTOWER Pure Sine Wave Inverters

1. Introduction

This manual provides detailed instructions for the safe and efficient use of your CHANTOWER Intelligent Power Inverter. Please read it carefully before operation.

Product Features

  • Lightweight in size, light in weight, high in efficiency, low in working noise, and reasonable in design.
  • Adopting efficient SPWM Pulse Width Control Technology.
  • Adopting multiple high-tech and intelligent driver chips.
  • SMT Chip Mounting Technology, precise control, high reliability, and low failure rate.
  • High efficiency conversion rate, strong load capacity, and wide application range.
  • Multiple intelligent security protection with complete protection functions.

Main Components

Front view of the CHANTOWER Pure Sine Wave Inverter with included battery cables.
Figure 1: Front view of the Inverter with battery cables.
Detailed view of inverter front and back panels, showing AC output, power switch, LCD display, heat dissipation holes, positive and negative DC input ports, and cooling fan.
Figure 2: Inverter front and back panel details.
  • Front Panel: Power ON/OFF switch, Heat dissipation holes, LCD display screen, AC Power outlets.
  • Rear Panel: Positive port (red), Cooling Fan, Negative port (black).
Close-up of the professional LCD display showing input voltage, battery power, output voltage, output frequency, fan operating status, and fan in action indicator.
Figure 3: Professional LCD Display details.

The LCD display provides real-time information including Input Voltage (DC), Battery Power status, Output Voltage (AC), Output Frequency, Fan Operating Status, and a Fan in action indicator.

2. Setup and Connection

Proper connection is crucial for the safe and effective operation of your inverter. Ensure the inverter voltage matches your battery voltage (e.g., 12V inverter for 12V battery).

Connection Method: Direct to Battery

When connecting directly to a battery, ensure the battery's voltage matches the inverter's input voltage (e.g., a 12V inverter requires a 12V battery). Multiple batteries can be used in parallel if needed.

Schematic diagram showing steps to connect the inverter to a battery and then to an appliance. Steps include connecting positive and negative terminals, tightening connections, and turning on the inverter switch.
Figure 4: Schematic diagram of usage.
  1. Connect the ring lug of the positive pole (red cable) to the inverter's positive terminal.
  2. Connect the ring lug of the negative pole (black cable) to the inverter's negative terminal.
  3. Ensure both terminals are securely tightened.
  4. Connect the other ends of the cables to the corresponding positive and negative terminals of your battery.
  5. Before connecting any device, ensure the inverter switch is in the OFF position.
  6. Connect your device to the AC output socket of the inverter.
  7. Finally, turn on the inverter switch.

Connection Method: Car Cigarette Lighters

This method is suitable for power inverters equipped with a car cigarette lighter model. The cigarette lighter output can only power electrical appliances with a load of less than 150W. If your appliance exceeds 150W, please use the direct-to-battery connection method.

Connection Method: Electric Motorcycle

For electric motorcycles, the inverter's input voltage must match the motorcycle's battery voltage (e.g., 48V or 60V). Select an inverter with the same voltage as your electric vehicle.

3. Operation

Operating Instructions

  1. Place the inverter switch in the OFF position, then connect the inverter to the battery and ensure good contact.
  2. Confirm that the power of all electrical appliances is within the rated power range (50% of the peak power marked by the inverter), and that the peak power of inductive load electrical appliances does not exceed the peak power marked by the inverter. Then, plug the electrical plug into the 110V/220V output socket of the inverter.
  3. Turn on the switch of the power inverter. The green indicator light will illuminate, indicating normal operation.
  4. The red indicator light indicates that the inverter is turned off due to overvoltage, undervoltage, overload, or overheating.
  5. In many cases, due to the limited output of the vehicle cigarette lighter socket, the normal inverter alarms or shuts down. In this case, as long as the vehicle is started or the power consumption is reduced, normal operation can be restored.

Matters Needing Attention

  • When appliances like refrigerator compressors or motors reach their peak power during startup, the inverter may trigger overload protection. In such cases, turn off the electrical switch first, then turn on the inverter switch, and then turn on electrical switches one by one, starting with the highest peak electrical appliance.
  • During use, if the battery voltage drops (e.g., 10.4-11.0V for a 12V battery), the inverter will sound a buzzing alarm. Turn off computers or other sensitive electrical appliances promptly. The inverter will stop outputting current when the voltage drops further (e.g., 9.7-10.3V for a 12V battery), and the red indicator light will illuminate.
  • Start the vehicle or charge the battery promptly to prevent battery depletion.
  • Although the inverter has overvoltage protection, exceeding the input voltage (e.g., above 16V for a 12V battery) can still damage the device.
  • After continuous use, the inverter's surface temperature may rise to 60°C. Ensure smooth airflow and keep it away from high-temperature-sensitive objects.
  • This power inverter is prohibited for use by minors.
Video 1: Demonstration of the inverter powering a kettle, drill, and hair dryer.
Inverter connected to a battery, successfully powering a refrigerator.
Figure 5: Inverter powering a refrigerator.
Inverter connected to a battery, powering multiple household appliances like a kettle, laptop, and blender, with a warning about protection functions and various application scenarios.
Figure 6: Inverter powering multiple appliances and application scenarios.
Diagram showing various appliances that can be powered by the inverter, including refrigerator, kettle, notebook, rice cooker, fan, projector, electric drill, television, air conditioner, freezer, and hair dryer.
Figure 7: Examples of compatible appliances.

4. Maintenance

To ensure the longevity and optimal performance of your inverter, follow these maintenance guidelines:

  • Keep Dry: Do not immerse the inverter in water or expose it to rain.
  • Temperature Control: Operate the inverter in a cool place with temperatures between 0°C and 40°C.
  • Ventilation: Ensure adequate airflow around the inverter. Do not cover the machine during use and avoid operating it in narrow, confined spaces.
  • Cleanliness: Keep the inverter clean. If the casing becomes dirty or old due to harsh environments, it may require professional cleaning or repair.
  • Cable Inspection: Regularly check all connecting wires and terminals for secure connections. Tighten any loose terminals.
  • Storage: When not in use for extended periods, store the inverter in a dry, cool place.

5. Troubleshooting

This section provides solutions to common problems you might encounter with your inverter.

Abnormal PhenomenonReasonResolution Method
The indicator light is not on, and the electrical appliance is not working.Malfunction caused by the battery.Check if the output voltage of the battery is consistent with the voltage marked on the machine, and replace it according to the specific situation.
Reverse connection of positive and negative poles.Check the battery connection. The power inverter may be damaged, and the machine needs to be replaced or returned for warranty.
Poor contact at the wiring.Check the connecting wires and connections, and tighten the wiring terminals.
The indicator light is red, and the electrical appliance is not working.Electrical appliance power exceeds continuous power of inverter, causing overload shutdown.Use electrical appliances with a power lower than the continuous power of the power inverter.
Electrical appliance power is less than continuous power, but peak power is too high.The peak power of the electrical appliances used should be within the peak power range of the power inverter.
Battery discharged (alarm).Charge or replace the battery.
Poor ventilation, causing overheating shutdown.Turn off the machine, cool down for 15 minutes, remove items around the fan and converter, place the inverter in a cool place, reduce the use of electrical appliances as required, and restart.
Input voltage too high.Check the working status of the charging system.
Detected that the output voltage of the power inverter is too low.The measured output voltage of voltmeter is too low.The output data of the correction wave inverter should be measured using a "true RMS multimeter" to obtain accurate data.
The power inverter emits a buzzing alarm sound.Undervoltage or over-temperature protection.Shorten or use thicker wires to connect the battery, lower the temperature of the machine, improve ventilation conditions around the machine, place the machine in a cool place, and reduce the use of electrical appliances as required.
The power inverter can only be used for low-power appliances.When current passes through a wire, the voltage decays.Reduce the length of the wire and use thicker wires.
Battery usage time is too short.Poor or damaged battery health.Replace the battery.
The electricity stored after being fully charged is still insufficient.The charger cannot fully charge the appliance. Replace it with a better intelligent charger.
Current decays as it passes through a wire.Reduce the length of the wire and use thicker wires.

6. Specifications

Main Technical Parameters

  • Output Voltage: 220V
  • Current Frequency: 50Hz/60Hz
  • Current Waveform: Corrected Sine Wave or Pure Sine Wave
  • Input Voltage: 10-15V / 22-30V / 40-60V / 60-80V
  • Built-in Fuse: 10A / 15A / 20A / 40A / 70A / 120A / 240A
  • Under Voltage Alarm: 10.4-11.0V / 20.5-22V / 42-45V / 54-57V
  • Low Pressure Shutdown: 9.7-10.3V / 19.4-20.6V / 39-42V / 48-52V
  • Overpressure Shutdown: 14.5-15.5V / 29-31V / 58-62V / 74-80V
  • No-load Energy Efficiency Data: No-load Current (<0.3A)
  • Input Voltage (for efficiency): 12V / 24V / 48V / 60V
  • Conversion Rate: (> 90%)

General Specifications

AttributeValue
Brand NameCHANTOWER
Model NumberPure Sine Wave Inverter 2200W 3000W 4000W
Output TypeSINGLE
Weight1.9 kg
Is Smart DeviceYes
OriginMainland China
CertificationCE
Peak Power1000W / 1600W / 2200W / 3000W / 4000W / 5000W
Continuous Power500W / 800W / 1100W / 1500W / 1600W / 2000W
Socket TypeUniversal (Commonly used in sockets in all countries)

7. User Tips

  • Voltage Matching: Always ensure your inverter's input voltage (e.g., 12V, 24V) precisely matches the voltage of the battery you are connecting it to. Mismatched voltages can cause damage.
  • Appliance Compatibility: While the inverter is powerful, it is not suitable for all high-power inductive loads. Avoid using it with appliances like induction cookers, microwave ovens, high-power hair dryers, and high-power air conditioners, as these can exceed the inverter's capacity or cause damage.
  • Power Limits: Pay close attention to both the continuous power and peak power ratings of your inverter. Ensure that the total continuous power of connected appliances does not exceed the inverter's continuous power rating, and that the startup (peak) power of any appliance does not exceed the inverter's peak power rating.
  • Heavy-Duty Tools: For tools like grinders or drills, ensure their power requirements (both continuous and peak) are well within the inverter's specifications to prevent overload.
  • Cable Thickness: If you experience voltage decay or the inverter struggles with certain loads, consider using shorter and thicker battery cables to minimize resistance and improve power delivery.

8. Warranty and Support

Warranty Terms

This product comes with a three-year warranty. To ensure proper after-sales service, customers must strictly follow the instructions when receiving the product.

  1. Product Exchange Application: Accessories must be complete and not affect secondary sales. Missing relevant accessories will result in a deduction based on factory price.
  2. Product Warranty Application: If the machine encounters quality problems without opening or modifying the original packaging, it will be repaired or replaced. If quality problems arise due to unauthorized opening or modification, maintenance will be charged.
  3. If the machine casing is too dirty or old and used in harsh environments, resulting in product damage, maintenance will be charged.
  4. For high-power machine casings that are severely scratched, dirty, or old, they should be returned to the factory for repair. After being repaired within the warranty period, the machine will be returned to the customer in its original condition and will be repaired for free. For machines that have been modified or unpacked without permission, any malfunctions will be subject to paid maintenance. Please contact customer service for specific costs.
  5. After receiving the relevant fees, we will promptly handle the after-sales service and deliver the product to the customer by express delivery.

Additional Support

For further assistance, you may refer to the official user manual PDF available at: User Manual (PDF). Please contact customer service to obtain the return address and phone number for returns and exchanges.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.