1. Introduction
Thank you for choosing the Viladepot MIG200 3-in-1 Welder. This inverter MIG welding machine combines three essential functions: MIG (Metal Inert Gas), Lift TIG (Tungsten Inert Gas), and MMA (Manual Metal Arc) welding. It is designed for versatility, suitable for welding various materials including carbon steel, stainless steel, copper, and titanium.
The MIG200 features IGBT high-frequency soft switch technology, ensuring high efficiency, a compact design, and portability. Its advanced control system significantly enhances welding performance, providing easy arc starting, a stable arc, high performance, minimal spatter, stable current, high reliability, and excellent weld-seam shaping.

Figure 1: Viladepot MIG200 3-in-1 Welder with key features highlighted.

Figure 2: Intelligent Digital Screen Display of the MIG200.
Video 1: Product demonstration showcasing the MIG200's features and welding processes.
2. Safety Precautions
It is crucial to read and understand all safety precautions before operating the welder to prevent accidents and ensure personal safety. Failure to follow these guidelines may result in serious injury or damage.
General Safety Precautions
- Always follow the precautions specified in this manual.
- Installation, power supply design, and use of high-pressure gas must comply with relevant standards and rules.
- Only qualified personnel are permitted to install, overhaul, maintain, and operate the welding machine.
- Ensure the welding machine is used solely for welding purposes and not for other applications like charging, heating, or pipeline unfreezing.
- Avoid placing the welding machine on uneven ground to prevent tipping.
Avoid Electrical Shock or Burn
- Touching live electrical parts is strictly forbidden.
- Ensure the welding machine is properly grounded by a professional electrician using a copper conductor of specific cross-section.
- The power source connection to the welding machine must also be done by a professional electrician with appropriate copper conductors. Insulating sheaths must not be damaged.
- Insulate your body from the base metal when working in wet or restricted areas.
- Use safety nets when working at heights.
- Always disconnect the input power when the machine is not in use.
Avoid Welding Fume and Gas Damaging Human Body
- Use specified exhaust equipment to prevent gas poisoning and suffocation.
- Be aware that protective gas can accumulate at the bottom of containers, leading to suffocation. Ensure adequate ventilation.
Avoid Welding Arc, Splash, and Slag Damaging Human Body
- Always wear protective glasses with sufficient shade. Welding arcs can cause ocular inflammation, and splashes/slag can burn eyes.
- Use appropriate protective gear for welding, including leather gloves, caftan, cap, welding spats, and apron, to protect against arc light, splashes, and slag burns.
Avoid Fire, Explosion, and Other Accidents
- The welding area must be free of combustible materials, as sparks and hot weld joints can cause fires.
- Ensure cables and base metal are firmly connected to prevent overheating and potential fires.
- Never weld in the presence of combustible gases or in containers that have held combustibles, as this can lead to explosions.
- Always have a fire extinguisher readily available.
To Prevent Injury from Rotating Moving Parts
- Keep fingers, hair, and clothing away from the cooling fan, wire feed roll, and other rotating parts.
- When feeding wire, keep the welding gun end away from your eyes, face, and body to prevent wire-related injuries.
Avoid Falling Gas Cylinder and Breaking Gas Regulator
- Gas cylinders must be securely fixed to prevent them from falling and causing injury.
- Do not store gas cylinders in high-temperature areas or direct sunlight.
- When opening a gas cylinder valve, keep your face away from the gas outlet to avoid injury from high-pressure gas.
- Use only the gas regulator provided by the manufacturer and follow its usage regulations.
Prevent Movement of Welding Machine
- Do not stand under the welding machine or in its direction of motion when moving it with a forklift or crane, as it may fall and cause injury.
- Ensure the lifting rope sling can withstand sufficient force and will not break when suspending the machine. The angle between the rope sling and hook should not exceed 30°.
3. Package Contents
The following items are included with your Viladepot MIG200 welding machine:

Figure 3: Included accessories for the Viladepot MIG200.
- MIG Welding Machine
- 3M 14AK MIG Torch
- Helmet
- Brush
- 2M Welding Holder
- 2M Ground Clamp
- Gas Nozzle (x2)
- Nozzle Holder (x2)
- 0.8mm Contact Tips (x5)
- 0.8MM 0.5KG Flux-Cored Wire
- User Manual (this document)
Note: A TIG torch is not explicitly listed as included in the standard package. If Lift TIG welding is desired, a separate TIG torch may be required.
4. Specifications
The technical parameters for the Viladepot MIG200 are provided below:
| Parameter | AC110V±15%, 50/60Hz | AC220V±15%, 50/60Hz |
|---|---|---|
| Model | MIG200 | |
| Rated Input Voltage (V) | AC110V±15%, 50/60Hz or AC220V±15%, 50/60Hz | |
| Rated Input Power (KVA) | MIG: 4.6, MMA: 5.6 | MIG: 4.6, MMA: 5.6 |
| Rated Input Current (A) | 42 (MIG), 50 (MMA) | 21 (MIG), 25 (MMA) |
| No-load Voltage (V) | 56V±5 | |
| Output Current (A) | 20-120 | 20-200 |
| Output Voltage (V) | 15-20 (MIG), 20.8-24.8 (MMA) | 15-21 (MIG), 20.8-24.8 (MMA) |
| Wire Diameter (mm) | Gasless flux cored wire 0.8-1.0 (1KG) | |
| Rated Duty Cycle (%) | 60 | |
| Efficiency (%) | 70 | |
| Insulation Grade | F | |
| Protection Grade | IP21 | |
| Weight (kg) | 6.6 | |
| Dimensions (mm) | 340*310*260 (Product Package) / 302*150*173 (Unit) | |
5. Installation
5.1 Environment Requirements
- Install in a dry environment with humidity less than 90% at 20°C and 50% at 40°C.
- Operating temperature range: -10°C to 40°C. Storage/transportation temperature: -20°C to 55°C.
- Protect the machine from direct sunlight and rain.
- Avoid using in environments with strong airflow when TIG welding.
- The inclination of the welding power should be less than 10°, and altitude no more than 1000m.
- Avoid dusty, acidic, or corrosive environments.
- Maintain a distance of more than 20cm from walls and 10cm from other welding machines for proper ventilation.
5.2 Input Power Source Requirements
- Waveform: Standard pure sine wave.
- Fluctuation range: 220V±15%.
- Frequency: 50Hz/60Hz.
- Connect the welding input power wire to the corresponding voltage level and a circuit breaker of ≥60A.
- Ensure good contact between the input power wire and the power terminal/switch to prevent oxidation.
- Use a multimeter to verify the input voltage is within the fluctuation range.
- Connect the yellow-green wire on the power cable and the grounding screw on the rear panel to a ≥4mm² wire and ground properly.
5.3 Machine Installation and Connections
Important Safety Note:
Before any electrical connection, ensure the power switch of the distribution panel is OFF. The equipment protection level is IP21; avoid using it in rain.
5.3.1 MMA Welding Connection
- Connect the welding cable to the machine.
- Turn off the machine.
- Connect the input cable to the distribution cabinet, then switch on.
- DC EP (Electrode Positive): Connect the workpiece to the negative pole (“-”), and the welding torch to the positive pole (“+”).
- DC EN (Electrode Negative): Connect the workpiece to the positive pole (“+”), and the welding torch to the negative pole (“-”).
5.3.2 MIG Welding Connection (No Gas Flux-Cored Wire)
- Place the flux-cored wire at the correct wire groove according to its diameter. Release the nut on the wire pressing wheel and feed the wire through the wire hose. Adjust the wire pressing wheel to apply sufficient pressure to prevent slipping, but do not over-press to avoid wire distortion.
- Connect the wire feeder polarity plug to the negative socket.
- Connect the earth clamp to the positive fast socket and tighten it clockwise.
- For the MIG torch, feed the wire out by inspecting it, choose the correct contact tip, tighten it, and press the gun switch to start.
- Fine-tune the voltage if the current and voltage are not well matched.

Figure 4: Wire Feed Wheel setup. The default is 1.0mm. If using 0.8mm wire, remember to flip it.
5.3.3 Lift TIG Welding Connection
- Connect the gas pipe of the TIG torch (if purchased separately) to the gas cylinder.
- Connect the separate type TIG torch to the negative socket, and the earth clamp to the positive socket.
- Scratch the tungsten electrode on the workpiece to initiate the arc, then lift the TIG torch.
- There is no control switch for gas flow and current on the machine for TIG. To avoid waste and for safety, turn off the gas cylinder and keep the torch away from the workpiece when not welding.
6. Operation
6.1 Front Panel Introduction
The control panel (Figure 5) is used for selecting welding functions and setting parameters.

Figure 5: Front Panel Introduction.
- Digital Display: Shows current welding parameters.
- Voltage Regulation (V knob): Fine-tunes welding voltage. Negative values decrease, positive values increase.
- Current Regulation (A knob): Sets current value for Lift TIG, MMA, and Gasless MIG modes.
- Function Selection Button: Cycles through Lift TIG, MMA, and Gasless Flux Cored Wire (0.8mm/1.0mm) modes.
- O.C. Indicator Light: Illuminates for machine over-temperature or abnormal conditions.
6.2 Welding Output Interface
The welding output interface consists of:
- MIG or MMA Torch Socket: For connecting the MIG torch or MMA electrode holder.
- Aviation Plug: (Not detailed in manual, typically for remote control or specific accessories).
- Anode Output Fasting Socket: Connect the workpiece for Lift TIG mode, the electrode holder for MMA mode, and the workpiece for Gasless MIG mode.
6.3 Welding Process Overview
6.3.1 Flux MIG Welding (No Gas)
This mode uses flux-cored wire, which generates its own shielding gas. It's ideal for outdoor use and welding thicker materials.
Video 2: Flux MIG welding demonstration.
Recommended Parameters for Flux Cored Wire Welding:
| Welding Current (A) | Wire Diameter (mm) |
|---|---|
| 60 ~ 80 | 0.6, 0.8 |
| 80 ~ 130 | 0.8, 1.0 |
| 130 ~ 200 | 0.8, 1.0 |
Formula for reference: U = 14 + 0.05I ± 3V
6.3.2 Lift TIG Welding
Lift TIG uses a tungsten electrode. The arc is initiated by touching the electrode to the metal and then lifting it, reducing contamination risk. This method is suitable for precision welding of thin materials like stainless steel, but generally excludes aluminum.
Video 3: Lift TIG welding demonstration.
Titanium and Alloy-TIG Parameter Reference:
| Thickness (mm) | Groove Shape | Welding Layer | Tungsten Diameter (mm) | Wire Diameter (mm) | Current (A) | Argon Gas Volume (L/min) | Nozzle Diameter (mm) |
|---|---|---|---|---|---|---|---|
| 0.5 | 1 | 1.5 | 1.0 | 30-50 | 8-10 | 10 | |
| 1.0 | I-shape | 1 | 2.0 | 1.0-2.0 | 40-60 | 8-10 | 10 |
| 1.5 | 1 | 2.0 | 1.0-2.0 | 60-80 | 10-12 | 10-12 | |
| 2.0 | 1 | 2.0-3.0 | 1.0-2.0 | 80-110 | 12-14 | 12-14 | |
| 2.5 | 1 | 2.0-3.0 | 2.0 | 110-120 | 12-14 | 12-14 | |
| 3.0 | 1-2 | 3.0 | 2.0-3.0 | 120-140 | 12-14 | 14-18 | |
| 4.0 | 2 | 3.0-4.0 | 2.0-3.0 | 130-150 | 14-16 | 18-20 | |
| 5.0 | Y-shape | 2-3 | 4.0 | 3.0 | 130-150 | 14-16 | 18-20 |
| 6.0 | 2-3 | 4.0 | 3.0-4.0 | 140-180 | 14-16 | 18-20 | |
| 7.0 | 2-3 | 4.0 | 3.0-4.0 | 140-180 | 14-16 | 20-22 | |
| 8.0 | 3-4 | 4.0 | 3.0-4.0 | 140-180 | 14-16 | 20-22 |
Thin Stainless Steel Sheet—TIG Parameter Reference:
| Thickness (mm) | Joint Type | Tungsten Diameter (mm) | Wire Diameter (mm) | Current Type | Current (A) | Argon Gas Volume (L/min) | Speed (cm/min) |
|---|---|---|---|---|---|---|---|
| 1.0 | butt | 2 | 1.6 | DCEN | 7-28 | 3-4 | 12-47 |
| 1.2 | butt | 2 | 1.6 | DCEN | 15 | 3-4 | 25 |
| 1.5 | butt | 2 | 1.6 | DCEN | 5-19 | 3-4 | 8-32 |
7. Maintenance
Proper maintenance is essential for the longevity and safe operation of your welding machine.
Warning:
All maintenance, service, and cleaning work must be performed with the power removed. Unplug the power cord before opening the casing. Blind experiments and imprudent overhauls can lead to further failures and complicate maintenance. Electronic equipment with exposed live parts can be dangerous; direct or indirect contact can cause electric shocks, potentially fatal.
7.1 Safety Points for Maintenance
- The welding machine is equipped with overcurrent and overheat protection circuits. If grid voltage, output current, or internal temperature exceed set standards, the machine will automatically stop. Excessive use (e.g., high voltage) can still damage the machine.
- Ensure good ventilation: When operating, a large working current passes through the machine. Natural ventilation may not be sufficient for cooling. A fan is installed for effective cooling. Ensure ventilation areas are not covered or blocked, and maintain a distance of at least 0.3 meters from surrounding objects.
- Avoid overloading: Operate the welder within its allowable load duration (refer to nameplate parameters). Overloading significantly shortens the welder's life and can cause burns.
- Forbidden voltage too high: If the power supply voltage exceeds the allowable value, it will damage the welder. Understand this risk and take preventive measures.
- Do not use the welding machine for thawing pipes.
- The back of each welding machine has a ground screw marked with a ground symbol. Before use, connect a cable with a cross-section greater than 2.5mm² to reliably ground the machine shell, releasing static electricity and preventing leakage.
7.2 Regular Maintenance
- Dedust regularly: Use dry, clean compressed air to clean the system. Dedust daily if operating in smoky or severely polluted conditions.
- Ensure compressed air is delivered at the required pressure to avoid damaging internal components.
- Check internal contact areas: Ensure tight connections (especially plug-in joints). Reinforce loose contacts. If rust or oxidation occurs, use sandpaper to remove the oxide film and reconnect.
- Avoid water and moisture penetration: If moisture occurs, perform a drying treatment inside the welder. Then conduct a megger insulation test, including insulation between connection joints, and between joints and casing. Welding can only resume if no errors are detected.
- Storage: If the welder is not used for a long period, seal it in its original packaging and store it in a dry condition.
8. Troubleshooting
The Viladepot MIG200 is designed with internal protection mechanisms. If the machine stops working unexpectedly, it may be due to one of the following reasons:
- Over-temperature Protection: If the internal temperature becomes too high, the temperature control switch will activate, stopping the machine and illuminating the yellow O.C. indicator light on the front panel. In this case, do not unplug the power supply; allow the cooling fan to continue running until the yellow light turns off, indicating the temperature has returned to normal.
- Overcurrent Protection: If the machine experiences an overcurrent, it may stop working. This could potentially damage some internal components. Exercise caution. After checking for any obvious issues, restart the machine. If the issue persists, contact support.
- Exceeding Standard Load Duration: The machine may enter a protection state if it operates beyond its rated load duration. Allow the machine to rest for the specified period before resuming operation.
If you encounter any issues not covered here, please refer to the full user manual or contact customer support.
9. User Tips
- TIG Torch: While the machine supports Lift TIG, the TIG torch is generally not included in the standard package. If you plan to use the Lift TIG function, ensure you acquire a compatible TIG torch separately.
- Aluminum Welding: This welder is suitable for precision welding of thin materials such as stainless steel and other metals, but it is generally not recommended for welding aluminum.
- Wire Feed Wheel: The wire feed wheel has a default setting for 1.0mm wire. If you are using 0.8mm wire, remember to flip the wire feed wheel to the correct setting for optimal performance.
- Manual Language: The primary manual is provided in English and German. For other languages, please check with the seller or manufacturer for availability.
10. Warranty and Support
During the warranty period, any fault arising from improper maintenance not authorized by the company will void the free repair service. For specific warranty terms and conditions, please refer to your purchase documentation or contact the seller directly.
For technical support or inquiries, please contact your retailer or the Viladepot customer service team.
11. Additional Resources
A detailed user manual in PDF format is available for download. This document contains comprehensive information on the product, including safety, installation, operation, and maintenance.