1. Introduction
Thank you for choosing the Viladepot CUT55 MAX plasma cutter. For your personal safety and to ensure proper equipment operation, please carefully read this manual and fully understand all instructions and safety precautions prior to operating the machine. Your attention and cooperation are greatly appreciated.
Product Characteristics
This inverter plasma cutting power source is capable of cutting carbon steel, low-alloy steel, stainless steel, high-alloy steel, and copper. It offers superior features due to its ideal output characteristics, excellent dynamic response, and precise control logic:
- Adopts IGBT high-frequency inverter technology for high efficiency, energy saving, and a lightweight, compact structure.
- Possesses outstanding control accuracy and adjustability, supporting diversified cutting processes with easy operation and strong versatility.
- Ensures reliable arc striking, stable arc performance, and consistent high-quality cutting results.
- Features low spatter, highly stable output current, reliable operation, and precise cutting formation.
- Equipped with a digital control interface for intuitive operation, multi-functionality, and fine parameter adjustment.
2. Safety Precautions
General Safety Precautions
- Strictly observe all precautions outlined in this manual to prevent accidents.
- Input power supply design, construction, site selection, and the use of high-pressure gas must comply with all applicable standards and regulations.
- Only qualified personnel are permitted to install, maintain, repair, or operate this equipment. Unauthorized personnel must not enter the work area.
- Do not use this machine for any purpose other than its intended cutting applications (e.g., never use for battery charging, heating, or pipe thawing).
- Secure the machine on a stable, level surface to prevent tipping or accidental movement.
- Always have a fire extinguisher readily available at the worksite.
Avoid Electrical Shock or Burn
- Do not touch live electrical parts.
- A qualified electrician must ground the machine using a copper conductor of the specified cross-section.
- A qualified electrician must connect the power supply to the machine using a copper conductor of the specified cross-section. Do not damage the insulating sheath.
- Ensure the operator and the workpiece are properly insulated when working in damp or confined spaces.
- Always use a safety net when working at heights.
- Always turn off the main power supply when the machine is not in use.
Avoid Fume and Gas Damaging Human Body
- Use specified exhaust equipment to prevent gas poisoning and suffocation.
- Protective gas may accumulate at the bottom of containers and cause suffocation; ensure adequate ventilation.
Avoid Splash Damaging Human Body
- Always wear appropriate shaded protective glasses. The arc can cause flash burns ("arc eye"), and sparks or slag can cause eye injury.
- Always use proper protective equipment, such as leather gloves, a flame-resistant jacket/coat, cap, spats, and apron, to shield against arc radiation, sparks, and hot spatter, which can burn the skin.
Avoid Fire, Explosion, Fracture, and Other Accidents
- Ensure the cutting area is clear of any combustible materials, as sparks and hot metal can cause a fire.
- Ensure all cables and the workpiece are firmly connected. Loose connections can overheat and pose a fire hazard.
- Do not cut near flammable gases or on containers that have held combustibles, as this may cause an explosion.
To Prevent Injury from Rotating/Moving Parts
- Do not allow fingers, hair, or clothing to come into contact with rotating parts such as cooling fans and wire feed rolls.
- When feeding wire, do not place the end of the plasma torch near the eyes, face, or body to avoid injury from the wire.
Avoid Gas Cylinder Falling and Regulator Damage
- Secure the gas cylinder reliably to prevent tipping and personal injury.
- Do not place gas cylinders in high-temperature environments or direct sunlight.
- When opening the gas cylinder valve, do not place the face near the gas outlet, as high-pressure gas may cause injury.
- Use only the gas regulator provided by the manufacturer and follow the usage regulations.
Prevent Injury During Equipment Movement
- Do not stand under the plasma cutter or in the direction of its movement when transporting it with a forklift or crane, as the equipment may fall and cause injury.
- When hoisting, the sling must have sufficient load-bearing capacity and must not be damaged. The angle between the sling and the hook shall not exceed 30°.
Precautions of Electromagnetic Compatibility (EMC)
Plasma cutting operations generate electromagnetic interference (EMI). Proper installation and correct operational methods are essential to minimize interference emissions. This equipment is classified as Class A industrial equipment. It is not intended for use in residential environments connected to a public low-voltage supply network, where EMC may not be ensured.
Before installing, evaluate potential electromagnetic disturbance by checking for other power/control/signal cables, nearby radio/TV/wireless equipment, computers/PLCs, safety-critical equipment, personnel with medical devices, and calibration instruments. Assess the EMC of other equipment to ensure normal operation.
Methods of Reducing Radiation Emission:
- Public Power Supply System: Connect in accordance with manufacturer's recommendations. Filters and shielded power cables (metal conduit or equivalent) may be necessary.
- Maintenance of Plasma Cutting Equipment: Perform routine maintenance. Keep all covers, panels, and doors securely closed. Do not modify the equipment unless expressly permitted. Adjustments to pilot arc generator or high-frequency stabilizer must follow manufacturer specifications.
- Plasma Cutting Torch & Work Cables: Keep as short as possible, routed close together, and positioned near the ground connection.
- Equipotential Bonding: Be aware of bonding between metal structures. Operator must remain insulated from all bonded metal objects.
- Workpiece Grounding (Earthing): Grounding the workpiece can reduce EMI but must be done safely and according to local regulations.
- Shielding: Shielding surrounding equipment and cables can mitigate EMI. For sensitive applications, shielding the entire cutting area may be necessary.
3. Specifications
| Attribute | Value |
|---|---|
| Model | CUT55 MAX |
| Power Voltage (V) | AC220V±15%, 50/60Hz |
| Rated Input Current (A) | 36 |
| Rated Input Capacity (KVA) | 8 |
| No-load Voltage (V) | 310 |
| Output Current Adjustment (A) | 20-55 |
| Rated Output Voltage (V) | 102 |
| Cyclic Duration Factor (%) | 40 |
| Efficiency (%) | 70 |
| Insulation Grade | F |
| Protection Grade | IP21 |
| Arc-striking Way | Arc-striking without contacting |
| Weight (KG) | 8.8kg |
| Dimensions (mm) | 455*315*345mm |
| Function | Cutting Metal |
| Current | 20-55A |
| Plasma ARC Starting | Non-Contact |
| Cutting Modes | 2T/4T, Pre/Post Flow |
| Clean cutting Thickness | 10mm |
| Max cutting Thickness | 15mm |
4. Brief Description of the Principle
The Viladepot CUT55 MAX plasma cutter utilizes IGBT high-frequency inverter technology. It converts 220V AC mains input into high-frequency alternating current via an IGBT-based inverter circuit. This current is then stepped down by a high-frequency transformer, rectified, and filtered to produce a stable direct current output for plasma cutting. This process enhances power supply dynamic response, reduces the size and weight of components, and improves overall operational efficiency.
The advanced control circuit ensures consistent cutting performance under varying external conditions, including grid voltage fluctuations and output cable length changes. This design provides reliable arc ignition, stable cutting, clean and precise results, and stepless current adjustment across the operating range.
5. Setup Instructions
Note: Strictly follow these steps for installation and commissioning! Before performing electrical connection operations, turn off the power switch of the distribution panel! The protection level of this equipment is IP21; do not use it in rainy conditions!
5.1 Electrical Connections
- Connect the plasma cutter's input power cable to the corresponding voltage level and a circuit breaker ≥60A (use a power cable ≥4mm²).
- Ensure the input power cable is in good contact with the corresponding power terminal or switch to prevent oxidation.
- Use a multimeter to measure whether the input voltage is within the allowable fluctuation range.
- Connect the yellow-green wire on the power cable and the grounding screw on the rear panel to a wire >4mm² and ensure reliable grounding.
- If the plasma cutter is placed on an inclined plane, secure the machine to prevent slipping.
- Each plasma cutter is equipped with an insulated handle; use the handle to lift and move the machine.
5.2 Plasma Cutting Output Interface
Connect the following components to the front panel interfaces (from left to right):
- Anode Output Interface: Connect the earth clamp in plasma cutting mode.
- Torch Switch Interface: Connect the cutting torch switch.
- Pilot Arc Interface: Connect the pilot arc cable of the cutting torch.
- Cathode Output Gas-Electric Connector: Connect the cutting torch in plasma cutting mode.
5.3 Air Pressure Installation and Operation
- Connect the gas hose to the air inlet on the back of the machine and the air outlet of the air compressor. Tighten the interface with hose clamps or other fittings.
- Ensure the air compressor can provide appropriate pressure, sufficient air flow, and dry air. If your existing air compressor cannot meet these requirements, use an air compressor and a pressure reducing filter with sufficient power.
- Wrap the copper air tap with sealing tape and tighten it on the IN and OUT ends.
- Wrap the regulator connector with sealing tape and tighten it on its mounting position.
- Fix the connector with nuts on the air pressure mounting position on the back panel of the machine.
- Screw the plastic nut to fix the air pressure gauge on the connector.
- Turn on the air pressure, lift the regulating knob upward, and adjust it to the required pressure value (turn toward "+" to increase, "-" to decrease).
- Adjust the pressure to 0.4MPa.
- Once the filter cylinder overflows, turn the drainage knob to discharge water (even in case of power outage).
- Maintain the pressure at 0.3-0.4MPa; for larger cutting current and thicker metal plates, appropriately increase the pressure.
- Small cutting current and excessively large air flow will cause arc breakage due to strong cooling effect.
Electrode and Cutting Tip Matching:
The sizes of the electrode and cutting tip should match the cutting current well. Matching the current with appropriate pressure reduces consumable consumption and material waste. The cutting thickness for stainless steel and aluminum is half of that for ordinary materials.
| Current (A) | 10-30 | 30-50 | 50-100 | 100-160 |
|---|---|---|---|---|
| Tip Size | Φ1.0mm | Φ1.2mm | Φ1.3mm | Φ1.4mm |
| Pressure (psi) | Recommended Cutting Thickness |
|---|---|
| 40(psi) | 1-6mm |
| 50(psi) | 6-10mm |
| 60(psi) | 10-20mm |
| above 60(psi) | more than 20mm |
6. Operating Instructions
6.1 Control Panel Functions
- Digital Display: Shows parameter values (e.g., current, pre/post flow time).
- 2T/4T Selection Button:
- 2T Mode: The cutting process is initiated and maintained by holding down the torch trigger. When the trigger is released, the cutting process stops. This mode is typically used for manual cutting operations where the worker has direct control over the start and stop of the cutting process.
- 4T Mode: Suitable for more automated cutting processes. The worker presses and releases the torch trigger to start the cutting process, and the machine continues cutting until the trigger is pressed and released again to stop. This mode is useful for longer cuts where the worker does not need to hold the trigger continuously.
- Pre/Post Flow Selection Button:
- Pre-flow Air (Front Air): The air flow starts a few seconds before the arc is struck to ensure that the cutting area is properly purged and ready for cutting. This helps in achieving a cleaner cut by removing any contaminants from the cutting area.
- Post-flow Air (Rear Air): The air continues to flow for a few seconds after the arc is extinguished. This helps in cooling the cut area and removing any residual molten metal, which can improve the quality of the cut and extend the life of the consumables.
- Parameter Adjustment Knob: Adjusts parameter values. A long press allows for rough adjustment.
6.2 CUT Plasma Cutting Operation
- Contact Arc-Striking: Touch the workpiece with the cutting torch and press the cutting torch switch button to start an arc. When the current rises to the preset value, begin plasma cutting.
- Non-Contact Arc-Striking: Keep a distance of 2-3mm between the cutting torch and the workpiece. Press the cutting torch button to strike the arc. When the current rises to the preset value, begin plasma cutting.
7. Maintenance
7.1 Safety Points for Maintenance
- The plasma cutter is equipped with over-current and over-heat protection circuits. If the grid voltage, output current, or internal temperature exceeds the rated range, the plasma cutter will stop operating automatically.
- Improper use (e.g., severe over-voltage) may still cause damage.
- Ensure good ventilation: The unit carries high working current. Ensure ventilation areas are not covered or blocked, maintaining a clearance of no less than 0.3 meters from surrounding objects.
- Do not overload the machine: Operate according to its rated load duration rate (refer to nameplate parameters). Do not exceed the maximum allowable operating current. Overload operation shortens service life and can cause damage. Load Duration Rate is defined as working time within a 10-minute cycle (working time + rest time = 10 minutes). For example, 30% at 200 A/28 V means 3 minutes of operation and 7 minutes of rest at 200 A output.
- Do not use over-voltage power supply: The applicable supply voltage is specified in the Main Performance Parameters table. Confirm voltage conditions and take proper protection measures.
- Grounding: A grounding screw with a grounding symbol is provided on the rear panel. Before operation, reliably ground the machine enclosure with a cable >2.5mm² to eliminate static electricity and prevent hazards.
7.2 General Maintenance Procedures
Warning: All maintenance, service, and cleaning work must be performed with power removed. Make sure you have unplugged the power cord before opening the casing.
- Dedust regularly: Use dry, clean compressed air to clean the system. Dedust daily when operating in smoky or severely polluted air.
- The compressed air should be delivered at the required pressure to avoid damaging internal components.
- Check internal contact areas: Ensure they are firmly connected (especially plug-in joints or components) and reinforce loose contacts. If rusting or oxidation occurs, use sandpaper to remove the oxide film and reconnect.
- Avoid water and moisture penetration: If this occurs, apply a drying treatment to the inside of the plasma cutter and then perform a megger insulation test (including insulation between connection joints and between joints and casing). Resume operation only if no error is detected.
If the plasma cutter is not used for a long period, seal it in the original packaging and store it in a dry condition.
8. Troubleshooting
Protection Codes
- Display shows "O.C.": This indicates the plasma cutter is in over-current protection or over-heat protection state.
- Over-Current Protection: This may be caused by damage to internal components or a misjudgment. Proceed with caution and restart the machine after confirmation. If it's a misjudgment, simply restart the machine.
- Over-Heat Protection: This protection is triggered by overheating of the internal temperature. Do not disconnect the power supply; allow the cooling fan to continue running until the yellow indicator on the front panel turns off. Normal cutting operation can be resumed when the temperature drops to a safe range.
Warning: Blind experiments and imprudent overhaul could lead to expanded failure and increased difficulty for formal maintenance. Electronic equipment with exposed voltage-carrying parts may pose dangers; any direct or indirect contact may lead to electric shock incidents, and severe electric shock will cause death!
9. User Tips
No specific user tips were available from provided reviews or Q&A content.
10. Warranty and Support
This product comes with a 12-month warranty from the date of sale to the end consumer. Under proper operation, its designed service life is 36 months.
If continued use is required after the end of its service life, the product must be maintained by a professional repair technician at the user's expense. Maintenance includes removing accumulated dust and wear residue. The product may only be put back into service after its service life if it is confirmed to still meet the safety requirements specified in this manual. If the product fails to meet the safety requirements, it must be disposed of.
If you encounter any problems, please contact us through the platform where your order was placed.
11. Transportation and Storage
- It is recommended to transport the product in a covered transport vehicle to ensure its safety and compliance with cargo transportation regulations.
- Measures must be taken during transportation to prevent the product from moving within the vehicle.
- The equipment should be strictly protected from moisture during transportation and storage.
- It should be stored in a dry, heated, and well-ventilated indoor environment with a temperature between +5°C and +40°C, and kept away from high humidity, corrosive gases, and dust.
Product Disposal
This product is not ordinary household waste. When the device reaches the end of its service life and needs to be disposed of, it must be taken to a designated special waste recycling point. The markings on the device indicate that it should not be discarded with regular household waste. Please hand over the device to an officially designated collection point for proper disposal, thereby contributing to environmental protection.