Makerbase MKS Gen-L

Contents

Makerbase MKS Gen-L 3D Printer Control Board User Manual

Models: MKS Gen-L V1.0, MKS Gen-L V2.1

1. Introduction

The Makerbase MKS Gen-L is a high-performance 3D printer control board designed for open-source Marlin firmware. It integrates the functions of Arduino Mega2560 and Ramps1.4 onto a single board, offering a compact and efficient solution for 3D printing enthusiasts. This manual provides essential information for setting up, operating, and maintaining your MKS Gen-L control board.

2. Features and Advantages

Image showing features and advantages of MKS Gen-L board

Image: List of features and advantages of the MKS Gen-L control board.

  • Combines 2560 and Ramps1.4 on one board, simplifying complex wiring.
  • Supports various stepper motor drivers (e.g., 4988, 8825, TMC2100).
  • External drive signal for larger motors (57, 86 motors).
  • High-quality MOSFET tube for better heat dissipation and stable operation.
  • Dedicated power chip (12V-24V) to address Ramps voltage conversion chip heating and insufficient power supply.
  • Stable and reliable filtering circuit to reduce interference and prevent freezing during printing.
  • CH340 serial port chip for cost-effective and reliable USB communication.
  • Accepts 24V input, reducing hotbed current to 1/4, solving heating issues for hotbed MOS tube.
  • Open-source Marlin firmware compatibility, configuration similar to Ramps1.4.
  • Direct connection for 2004LCD, 12864LCD, TFT28, and TFT32 touchscreen displays.
  • XYZ axis uses terminals with different colors for motor and limit switch connections, enhancing convenience.
  • Humanized design with terminals of different colors to distinguish driving direction, reducing reverse insertion damage.

3. Specifications

Attribute Value
Type Voltage Regulator (3D Printer Control Board)
Origin Mainland China
Condition New
Input Voltage 12V-24V
Microcontroller Arduino Mega2560 compatible
Stepper Driver Support A4988, DRV8825, TMC2100, TMC2130 SPI, TMC2208 UART, TMC2209 UART
Display Support 2004LCD, 12864LCD, TFT28, TFT32
USB Chip CH340

Dimensional Drawing (MKS Gen-L V2.0/V2.1)

Dimensional drawing of MKS Gen-L V2.0/V2.1 board

Image: Dimensions of the MKS Gen-L V2.0/V2.1 board in millimeters. Length: 110mm (overall), 102mm (mounting holes). Width: 84mm (overall), 76mm (mounting holes). USB port offset: 22mm from left, 12mm wide. AUX-1 port offset: 26mm from USB, 17.7mm wide. EXP1/EXP2 ports: 20mm each, 19mm spacing from bottom.

4. Setup Guide

4.1 General Precautions

Important safety precautions for MKS Gen-L board

Image: Text outlining special attention points for board usage.

  • Ensure positive and negative poles are connected correctly before powering on.
  • DO NOT plug or unplug the motor and driver when the power is on. This can burn out the driver.
  • DO NOT adjust the current while the motor is running. The correct way is to disconnect power, unplug the motor, re-power on, adjust the potentiometer, and measure the voltage until it matches the expected value.
  • DO NOT plug the driver in reverse, as this will burn out the driver and potentially the motherboard.
  • It is recommended NOT to connect the USB cable and 12V power supply at the same time during the firmware burning process. After burning, connect the 12V supply.

4.2 Board Overview and Pin Map

Familiarize yourself with the layout and pin assignments of your MKS Gen-L board.

MKS Gen-L V1.0 Pin Map

Pin map for MKS Gen-L V1.0 control board

Image: Detailed pin map for the MKS Gen-L V1.0 board, showing connections for motors (X, Y, Z, E0, E1), fans, hotend, hotbed, endstops, servos, and auxiliary ports.

MKS Gen-L V2.1 Labeled Diagram

Labeled diagram for MKS Gen-L V2.1 control board

Image: Labeled diagram of the MKS Gen-L V2.1 board, indicating connections for 12/24V power, X/Y/Z/E0/E1 axis motors, fan, hotbed, hotend, LCD screen, servos, expansion ports, USB, touchscreen, and limit switches.

MKS Gen-L V2.1 Schematic/Pinout

Schematic and pinout for MKS Gen-L V2.1 control board

Image: Detailed schematic and pinout for the MKS Gen-L V2.1 board, showing pin assignments for TMC2208-UART, TMC2130-SPI, and various other connections.

4.3 Wiring Diagram (MKS Gen-L V1.0 Example)

Wiring diagram for MKS Gen-L V1.0

Image: Comprehensive wiring diagram for the MKS Gen-L V1.0 board, illustrating connections for power, motors, limit switches, hotend, hotbed, fan, USB, touchscreen, and expansion ports.

4.4 Driver Settings

The MKS Gen-L series supports various stepper motor drivers and operating modes. The following settings are based on the MKS series drivers. Drivers from different manufacturers may have different settings. Always refer to the specific driver's documentation for detailed configuration.

4.4.1 Step/Dir Normal Operation Mode

Driver setting for Step/Dir normal operation mode on MKS Gen-L V2.1

Image: Diagram showing jumper cap placement for Step/Dir normal operation mode on MKS Gen-L V2.1. In this mode, insert the jumper cap into the blue area according to your needs. For drivers like A4988, LV8729, TB67S109, subdivision is adjusted through the jumper cap. It is not recommended to insert a jumper cap on the fourth pin, as it may affect the use of some drivers.

4.4.2 UART Mode (MKS TMC2208 V2.0 Example)

Driver setting for UART mode on MKS Gen-L V2.1 with TMC2208

Image: Diagram showing jumper cap placement for UART mode on MKS Gen-L V2.1 using TMC2208. When the motor driver is in UART mode, remove all jumper caps under the driver (jumper caps are not allowed). Insert one jumper cap on the UART pin on the motherboard. Refer to the Marlin firmware manual for setting up the driver part.

4.4.3 SPI Mode (TMC2130 Example)

Driver setting for SPI mode on MKS Gen-L V2.1 with TMC2130

Image: Diagram showing jumper cap placement for SPI mode on MKS Gen-L V2.1 with TMC2130. Due to the internal circuit support, TMC2130 or other types of drivers no longer need jumpers for SPI mode. The setting can be completed by inserting jumper caps on all four green rows on the left. Refer to the Marlin firmware manual for SPI mode settings.

4.5 MKS Gen-L V1.0 vs V2.1 Comparison

Comparison of MKS Gen-L V1.0 and V2.1 boards

Image: Side-by-side comparison of MKS Gen-L V1.0 and V2.1 boards. The main difference in V2.1 is that TMC2130 SPI, TMC2208, and TMC2209 UART modes are directly plug-in, using jumper caps for jumpering, and no flying wires are needed.

4.6 MKS MINI12864 V3 Display Connection

MKS MINI12864 V3 display module

Image: MKS MINI12864 V3 display module. This display can be directly connected to the MKS Gen-L board. Ensure correct orientation and pin alignment during connection.

5. Operating Instructions

The MKS Gen-L board is designed to run open-source firmware like Marlin. Basic operation involves:

  1. Firmware Flashing: Connect the board to your computer via USB. Use an Arduino IDE or similar tool to upload the Marlin firmware. Ensure the correct board (Arduino Mega 2560) and port are selected.
  2. Configuration: Customize the Marlin firmware (Configuration.h and Configuration_adv.h) to match your 3D printer's specific components (e.g., thermistors, endstops, motor steps/mm, bed size).
  3. Power On: After flashing and wiring, connect the 12V/24V power supply.
  4. Testing: Use a host software (e.g., Pronterface, OctoPrint) to send G-code commands to test motor movements, heater functions, and endstops.
  5. Printing: Load your G-code files via SD card (if supported by your display) or directly from a host computer.

6. Maintenance

  • Keep Clean: Regularly clean the board to prevent dust accumulation, which can lead to overheating or short circuits. Use compressed air or a soft brush.
  • Inspect Connections: Periodically check all wiring connections for looseness or damage. Ensure screw terminals are tight.
  • Firmware Updates: Keep your firmware updated to benefit from new features, bug fixes, and improved performance.
  • Environmental Conditions: Operate the board in a dry, stable environment, away from extreme temperatures and humidity.
  • Heat Sinks: Ensure stepper motor drivers have proper heat sinks and adequate airflow to prevent overheating.

7. Troubleshooting

  • Board Not Powering On:
    • Check power supply connections and voltage.
    • Ensure the power supply is functional.
    • Verify no short circuits on the board.
  • Motors Not Moving:
    • Check motor wiring for correct polarity and connection.
    • Verify stepper motor drivers are correctly inserted and configured (Step/Dir, UART, SPI modes).
    • Ensure driver current is set appropriately.
    • Check firmware configuration for motor definitions and steps/mm.
  • USB Connection Issues:
    • Install the CH340 driver on your computer.
    • Try a different USB cable or port.
    • Ensure the board is powered externally if needed for communication.
  • Heaters Not Working:
    • Check thermistor and heater wiring.
    • Verify thermistor type and heater pins are correctly configured in firmware.
    • Ensure power supply can provide enough current for heaters.
  • Display Not Working:
    • Check display cable connections (EXP1, EXP2).
    • Verify display type is enabled and configured in firmware.
    • Ensure correct display module (e.g., MKS MINI12864 V3) is used.

8. User Tips

  • Start Simple: If you're new to 3D printer electronics, begin with basic configurations and gradually add more complex features.
  • Double-Check Wiring: Before powering on, always double-check all wiring connections, especially power and motor polarities, to prevent damage.
  • Backup Firmware: Always save a backup of your working firmware configuration before making significant changes.
  • Community Support: Leverage online communities and forums (like those for Marlin firmware) for troubleshooting and advanced configurations.
  • Use Quality Components: While the MKS Gen-L is cost-effective, using good quality stepper motor drivers and power supplies will enhance reliability and performance.

9. Warranty and Support

For technical support, firmware, and additional resources, please refer to the official Makerbase GitHub repository and related blogs:

Links to Makerbase GitHub and user manuals

Image: Links to Makerbase GitHub and blog posts for user manuals.

Please note that these links are external resources and their availability may vary.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.