Mudiro M-JC3

Contents

Mudiro M-JC3 Car Jump Starter with Air Compressor User Manual

Model: M-JC3 | Brand: Mudiro

Introduction

Thank you for choosing the Mudiro M-JC3 Car Jump Starter with Air Compressor. This versatile device combines a powerful jump starter, a high-pressure tire inflator, a portable power bank, and an emergency lighting system into one compact unit. Designed for reliability and ease of use, the M-JC3 is an essential tool for any vehicle owner, providing peace of mind for roadside emergencies and outdoor activities. Please read this manual thoroughly before operating the device to ensure safe and optimal performance.

Package Contents

Please check the package to ensure all items are present:

  • 1 x Mudiro M-JC3 Jump Starter with Air Compressor
  • 1 x Smart Jumper Cables
  • 1 x Air Pump Hose
  • 3 x Gas Nozzles (various types)
  • 1 x Backup Air Tube
  • 1 x Type-C Charging Cable
  • 1 x User Manual (this document)
  • 1 x Portable EVA Carrying Case
Diagram of Mudiro M-JC3 package contents
Figure 1: Contents of the Mudiro M-JC3 package, including the jump starter, cables, hose, nozzles, and case.

Specifications

FeatureSpecification
ModelM-JC3
Peak Current6000A
Jump Start CapacityUp to All Gas / 10.0L Diesel engines
Starts Per Charge50+
Operating Temperature-4°F to 140°F (-20°C to 60°C)
Air Compressor Max Pressure150 PSI
Airflow Rate45L/Min
Inflation Speed (195/65R15 tire)30 PSI to 36 PSI in 1 minute
Power Bank OutputUSB-A (5V/2.4A, 9V/2A, 12V/1.5A), Type-C (5V/3A, 9V/3A, 15V/2A)
Fast Charging (PD)30W (Full charge in 1.5 hours)
Emergency Light Output600LM (Flashlight, SOS, SOS+Red/White Strobe, Side Lights)
DisplayHD Daylight-Viewable LCD
Safety Protection10-layer protection (overcharge, short-circuit, extreme temps, etc.)
Battery Capacity12000-18000 mAh
Number of Built-in Batteries4
Conversion Rate>90%
CertificationsCE, FCC, MSDS, ROHS
OriginMainland China

Important Safety Warnings

  • Read all instructions before using the product.
  • Do not start the car under load conditions.
  • Ensure the jump starter's power is greater than 50% before attempting to jump start a vehicle.
  • Do not allow the red and black clamps to touch each other or connect to the same metal piece.
  • Do not disassemble the unit. Refer servicing to qualified personnel.
  • Keep out of reach of children.
  • Do not expose the product to rain or extreme moisture.
  • If abnormal heating is detected after charging or use, immediately stop using the device and keep it away from flammable materials.
  • Store in a dry, cool place to avoid circuit corrosion caused by humid environments.

Setup and Initial Charging

Before first use, fully charge your Mudiro M-JC3 jump starter.

Charging the M-JC3 Unit

  1. Connect the provided Type-C charging cable to the Type-C input port on the M-JC3.
  2. Connect the other end of the cable to a 30W PD wall charger (not included) or a suitable USB power adapter.
  3. The LCD screen will indicate the charging status and battery level. A full charge typically takes about 1.5 hours with a 30W PD input.
Diagram showing PD30W fast charging for the jump starter
Figure 2: The M-JC3 supports PD30W fast charging, allowing a full charge in 2 hours and 50% charge for devices in 30 minutes.

Operating Instructions

Jump Starting a Vehicle

The M-JC3 can jump start 12V vehicles with up to All Gas or 10.0L Diesel engines.

  1. Ensure the jump starter has at least 50% battery charge.
  2. Insert the smart jumper cable's blue plug firmly into the jump starter's 12V output port.
  3. Connect the red clamp to the positive (+) terminal of the vehicle's battery.
  4. Connect the black clamp to the negative (-) terminal of the vehicle's battery.
  5. Once connected correctly, the indicator on the smart jumper cable will turn green.
  6. Start your vehicle's engine.
  7. Once the engine starts, immediately remove the clamps from the car battery, then disconnect the smart jumper cable from the jump starter.
Step-by-step guide on how to jump start a car using the Mudiro M-JC3
Figure 3: Visual guide for jump starting: 1. Insert clips into jump starter. 2. Connect clamps to 12V car battery (Red to positive, Black to negative). 3. Start engine when indicator turns green.
Mudiro M-JC3 jump starter connected to a car battery, highlighting its 6000A peak current capability
Figure 4: The M-JC3 can deliver 6000A peak current, suitable for various vehicles including those with 8.0L Diesel engines.

Using the Air Compressor

The M-JC3 features a 150 PSI air compressor for inflating tires and other items.

  1. Connect the air pump hose to the inflation port on the M-JC3.
  2. Attach the appropriate gas nozzle to the hose and then to the item you wish to inflate (e.g., tire valve).
  3. Turn on the M-JC3. The LCD screen will display the current pressure.
  4. Use the control buttons to select the desired inflation mode (car, bike, motorcycle, ball, custom) and pressure unit (BAR, PSI, KPA, kg/cm²).
  5. Set the target pressure using the '+' and '-' buttons.
  6. Press the power button to start inflation. The compressor will automatically stop once the target pressure is reached.
  7. Disconnect the hose and nozzle from the item and the M-JC3.
Mudiro M-JC3 tire inflator in use, showing 150 PSI capability and quick inflation time
Figure 5: The M-JC3's 150 PSI air compressor can inflate a standard car tire from 30 to 36 PSI in approximately 1 minute.

Using as a Portable Power Bank

The M-JC3 can charge various electronic devices via its USB-A and Type-C output ports.

  1. Connect your device's charging cable to one of the USB output ports (USB-A or Type-C) on the M-JC3.
  2. The M-JC3 will automatically begin charging your device.
  3. Monitor your device's charging status.
Mudiro M-JC3 functioning as a portable power bank, charging multiple devices
Figure 6: The M-JC3's dual USB-A and Type-C ports allow charging of phones, tablets, drones, smartwatches, and other electronics.

Using the Emergency Lighting

The M-JC3 features dual LED lights with multiple modes for various situations.

  1. Press the light button (usually marked with a flashlight icon) to cycle through the lighting modes.
  2. Available modes include: Flashlight, SOS, SOS + Red/White Strobe, and Side Lights.
  3. Select the appropriate mode for your needs (e.g., flashlight for repairs, SOS for emergencies).
Mudiro M-JC3 emergency lighting system with 600LM output and multiple modes
Figure 7: The 600LM emergency lighting system offers flashlight, SOS, SOS & Red-White Strobe, and floodlight modes for visibility.

Maintenance and Storage

  • Regular Charging: When not in use for a long time, regularly (every 3 months) charge the battery to 50%~80% capacity to protect its lifespan.
  • Cleaning: Wipe the unit with a dry, soft cloth. Do not use harsh chemicals or abrasive materials.
  • Storage: Store the M-JC3 in a dry, cool place, away from direct sunlight and extreme temperatures. Use the provided portable EVA carrying case to keep all accessories organized and protected.
  • Accessory Storage: The hidden rear storage compartment securely holds 3 inflation nozzles and 1 spare tube, ensuring they are consolidated and accessible.

Troubleshooting

The M-JC3 features an HD daylight-viewable LCD that displays battery level, inflation mode, real-time pressure, and error indicators. Refer to the screen for diagnostic information.

Mudiro M-JC3 large smart screen displaying various indicators and error messages
Figure 8: The smart screen provides real-time information including battery level, voltage, and error warnings like USB Input/Output Error, Low Battery Voltage, Battery Overheating, and Motor Overheating.
ProblemPossible CauseSolution
Vehicle won't jump startJump starter battery too low (<50%)
Incorrect clamp connection
Vehicle battery severely damaged
Charge the jump starter to over 50%
Ensure red clamp is on positive (+), black on negative (-)
Consult a mechanic if battery is beyond jump starting
Air compressor not inflatingHose/nozzle not securely connected
Target pressure not set
Unit battery too low
Check all connections for leaks
Set desired pressure on LCD
Charge the jump starter
Device not charging from power bank functionCable issue
Device not compatible
Unit battery too low
Try a different charging cable
Check device's charging requirements
Charge the jump starter
Abnormal heating during use/chargingOverload or internal faultImmediately stop use/charging. Disconnect and keep away from flammable materials. Contact support.

User Tips

  • Always keep the jump starter charged, especially before long trips or periods of non-use.
  • Familiarize yourself with the different inflation modes and pressure units to quickly adapt to various inflation needs.
  • Utilize the emergency lighting for roadside visibility or as a general work light during repairs.
  • The compact size and integrated storage make it easy to keep all components together in your vehicle.

Warranty and Support

The Mudiro M-JC3 comes with a 2-Year Hassle-free Warranty and Lifetime Technical Support Service. For any questions, issues, or technical assistance, please contact Mudiro customer support through your purchase platform or the contact information provided in your product documentation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.