Midea US1-KFR35G BP2N1Y-MAB (P0) 02BY10344F0

Contents

Midea Air Conditioning Display Receiving Board User Manual

Model: US1-KFR35G BP2N1Y-MAB (P0) 02BY10344F0

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Midea Air Conditioning Display Receiving Board, model US1-KFR35G BP2N1Y-MAB (P0) 02BY10344F0. Please read this manual thoroughly before attempting any installation or operation to ensure proper function and safety.

Midea Air Conditioning Display Receiving Board circuit board
Figure 1: Overview of the Midea Air Conditioning Display Receiving Board, showing the 7-segment display, various connectors, and component layout. Key identifiers such as US1-KFR35G, BP2N1Y-MAB, and 02BY10344F0 are visible on the board.

Setup and Installation

The display receiving board is a critical component for Midea air conditioning units, responsible for displaying operational status and receiving signals. Installation should only be performed by qualified personnel.

Safety Precautions:

  • Always disconnect power to the air conditioning unit before installation or maintenance.
  • Wear appropriate personal protective equipment (PPE).
  • Ensure proper grounding to prevent electrical shock.
  • Handle the circuit board by its edges to avoid damaging components or static discharge.

Installation Steps:

  1. Locate the existing display receiving board within the Midea air conditioning unit.
  2. Carefully disconnect all wiring harnesses and connectors from the old board. Note the orientation and connection points for each wire.
  3. Remove any mounting screws or clips securing the old board.
  4. Position the new Midea Air Conditioning Display Receiving Board (Model: US1-KFR35G BP2N1Y-MAB (P0) 02BY10344F0) in the designated slot.
  5. Secure the new board using the original mounting hardware.
  6. Reconnect all wiring harnesses and connectors to their corresponding ports on the new board. Refer to the labels on the board (e.g., "DISPLAY", "REC") and the original wiring configuration.
  7. Ensure all connections are firm and correctly seated.
  8. Once installed, restore power to the air conditioning unit and test its functionality.

Operating Instructions

This display receiving board functions as an interface for your Midea air conditioner. Its primary role is to display operational information and receive commands from the remote control or control panel.

Display Functions:

  • The 7-segment display (as seen in Figure 1) typically shows temperature settings, error codes, or operational modes.
  • Indicators (LEDs) may illuminate to show power status, fan speed, or specific functions (e.g., "REC" for receiving signals).

Receiving Commands:

  • The board is designed to receive infrared (IR) signals from the air conditioner's remote control.
  • Ensure there is no obstruction between the remote control and the receiving sensor on the display board.

Maintenance

Proper maintenance ensures the longevity and reliable operation of your display receiving board.

  • Cleaning: Periodically, with the power disconnected, gently clean the surface of the board and display with a soft, dry cloth. Avoid using liquid cleaners or abrasive materials.
  • Inspection: Regularly inspect connectors for corrosion or loose connections. Ensure the board is securely mounted.
  • Environmental Conditions: Ensure the air conditioning unit's internal environment is free from excessive moisture, dust, and extreme temperatures, which can degrade electronic components.

Troubleshooting

If you encounter issues with your Midea Air Conditioning Display Receiving Board, refer to the following common troubleshooting steps:

ProblemPossible CauseSolution
Display is blank or erratic.Loose connection, power issue, faulty board.Check all cable connections. Verify power supply to the unit. If issues persist, the board may need replacement.
Remote control commands not received.Obstruction, remote battery low, faulty IR receiver.Remove any obstructions. Replace remote control batteries. Ensure the remote is pointed directly at the unit's receiver.
Incorrect temperature or mode displayed.Sensor issue, software glitch.Restart the air conditioning unit by cycling its power. If the problem continues, consult a professional technician.

For complex issues, it is recommended to contact a certified Midea service technician.

Specifications

FeatureDetail
Model NumberUS1-KFR35G BP2N1Y-MAB (P0) 02BY10344F0
BrandMidea
Product TypeAir Conditioning Display Receiving Board
Fixed TypeMagnetic Fastener
UseWindow (likely referring to compatible AC unit type)
OriginMainland China
Package Weight0.2 kg
Package Dimensions (L x W x H)9 cm x 4 cm x 6 cm

User Tips

  • Before replacing the board, take a photo of the existing wiring to ensure correct re-connection.
  • If the display shows an error code, consult your air conditioner's main user manual for the specific meaning of the code.
  • Ensure the replacement board matches the exact model number of your original board for compatibility.

Warranty and Support

This Midea Air Conditioning Display Receiving Board is designed for durability and performance. For specific warranty information, please refer to the terms provided by your original seller or Midea's official support channels. In case of technical difficulties or questions not covered in this manual, please contact the seller or a qualified HVAC technician.

Seller: Chinese Factories Global Store

Store Home Page: Chinese Factories Global Store

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.