1. Introduction
This manual provides essential information for the safe and effective operation of your BAOFENG GMSK Digital W31D Walkie Talkies. Please read all instructions carefully before use to ensure proper functionality and to prevent bodily injury or property loss.
1.1 Intended Use
Our products are designed to provide reliable wireless communication services across various industry sectors. To ensure safe use and optimal performance, the product must be used as intended. The operator is responsible for any damage resulting from use beyond the intended instructions.
Intended use includes:
- Use by individuals fully aware of RF exposure and capable of controlling it to meet occupational limits in FCC/ICNIRP and international standards.
- Adherence to all security instructions in this document.
- Compliance with general, national, and in-house safety regulations.
- Exclusive use with frequencies licensed by the respective authority.
- Appropriate configuration by the dealer.
Operators should be well-trained and familiar with applicable standards, regulations, and provisions.

Figure 1.1: BAOFENG W31D Walkie Talkie suitable for various occasions.
2. Safety Information
Alervites is not liable for any failures or problems caused by the use or misuse of this product by the purchaser or any third party. Alervites is also not liable for damages caused through the use of this product by the purchaser or any third party, except in cases where ordered to pay damages under the laws.
2.1 Types and Meanings of Marks
- ▲ DANGER! This mark indicates an imminently hazardous situation, which, if not avoided, could result in death or serious injury.
- ▲ WARNING! This mark indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
- ▲ CAUTION! This mark indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury or only property damage.
2.2 DANGER!
- Do not use this product in “an area where use of it is prohibited”, e.g., inside a hospital or on a train. This product can affect electronic or medical devices.
- Do not use this product while riding a bicycle or driving a car. Accidents can result. Stop the bicycle or car at a safe place before using this product.
- Do not perform transmission in a crowded place for the safety of persons using a medical device such as a cardiac pacemaker. The radio wave emitted from this product can cause the medical device to malfunction and result in an accident.
- Do not touch any material leaking from the battery pack with bare hands. The chemical that has stuck to your skin or entered your eye can cause chemical burns. In such a case, consult a doctor immediately.
- Those who are carrying a medical device such as a cardiac pacemaker should not perform transmission near the device. When transmitting, use an external antenna and keep as far as possible away from the external antenna. The radio wave emitted by the transmitter can cause the medical device to malfunction and result in an accident.
- Do not use this product or the battery charger in a place where inflammable gas is generated. A fire or explosion can occur.
2.3 WARNING!
- Do not solder or short-circuit the terminal of the battery pack. A fire, leak, overheating, explosion, or ignition can result. Do not carry the battery pack together with a necklace, hair pin, or small metal objects. A short circuit can result.
- Do not power this transceiver with a voltage other than the specified power supply voltage. A fire, electric shock, or damage may result.
- Do not use the battery pack for any model other than the specified transceiver. A fire, leak, overheating, explosion, or ignition can result.
- Do not make very long transmissions. The main body of the transceiver may overheat, resulting in a failure or burns.
- Do not disassemble or make any alteration to this product. An injury, electric shock, or failure can result.
- When transmitting, keep the transceiver at least 5.0 mm (3/16 inch) away from your body. Use only the supplied antenna. Do not use modified or damaged antennas.
- Keep the terminals of the battery pack clean. If terminal contacts are dirty or corroded, a fire, leak, overheating, explosion, or ignition can result.
- Do not handle the battery pack or charger with wet hands. Do not insert or remove the power plug with wet hands. An injury, leak, fire, or failure can result.
- If smoke or strange odor is emitted from the main body, battery pack, or battery charger, immediately turn the transceiver off; remove the battery pack, and remove the power plug from the outlet. A fire, leak, overheating, damage, ignition, or failure can result. Contact the dealer or Alervites Customer Support.
- Do not use a battery pack which is externally damaged or deformed. A fire, leak, heating, explosion, or ignition can result.
- Do not use any battery charger which is not specified by Alervites. A fire or failure can result.
- If charging of the battery pack cannot be completed within the specified charging time, immediately remove the power plug of the battery charger from the outlet. A fire, leak, overheating, explosion, or ignition can result.
2.4 CAUTION!
- Do not dangle or throw this product by holding its antenna. This product can hit and injure someone. In addition, doing so can result in a transceiver failure or damage.
- Do not use transceiver in a crowded place. The antenna can hit someone, resulting in an injury.
- Do not place this transceiver in a place subject to direct sunlight or near a heater. The transceiver can deform or discolor.
- Do not place this transceiver in a humid or dusty place. A fire or failure can result.
- During transmission, keep the antenna as far from you as possible. Long-time exposure to electromagnetic waves can have a negative impact on your health.
- Do not clean the case with thinner or benzene. Use a soft, dry cloth to clean the case.
- If the transceiver is not being used for an extended period, turn it off and remove the battery pack for safety.
- Do not drop, strike, or throw the transceiver. A failure or damage may result.
- Keep magnetic cards and video tape away from the transceiver. The data recorded on cash cards or video tape can be erased.
- Charge the battery pack within the temperature range from +5 °C to +35 °C (+41 °F to +95 °F). Charging the battery pack outside this temperature range can cause leak, overheating, decrease in performance, or reduction in service life.
- When unplugging the power cord of the battery charger, be sure to hold the power plug. Pulling the power cord can damage it and cause a fire or electronic shock.
- Do not use earphones or headphones at an extremely high volume level. Hearing impairment can result.
- Keep this product out of reach of children. An injury, etc. can result.
- Install the belt clip securely. If they are installed improperly, the transceiver may fall or drop, resulting in an injury or damage.
- Do not place a heavy object on the power cord of the battery charger. The battery cord can be damaged, resulting in a fire or electric shock.
- Do not use the included battery charger to charge any battery pack which is not specified for use with the charger. A fire can result.
- Do not operate the transmitter near the TV or radio. Radio disturbance can occur in the transceiver, the TV, or the radio.
- Do not use any products other than the specified options and accessories. A failure can result.
- When the battery charger is not in use, remove its power plug from the outlet.
- Before discarding the worn battery pack, affix tape or the like to its terminals.
- Before using this transceiver in a hybrid or fuel-saving car, be sure to check with the automobile manufacturer regarding use of the transceiver in that car. Noise generated by an onboard electrical device (inverter, etc.) can disrupt the normal operation of the transceiver.
- Do not use at extremely low atmospheric pressure.
3. Package Contents
Verify that all items are present and in good condition upon unpacking. If any item is missing or damaged, please contact your dealer.
- 1 or 2 x Radio (depending on purchase option)
- 1 or 2 x Antenna (depending on purchase option)
- 1 or 2 x Li-Ion Battery Pack (depending on purchase option)
- 1 or 2 x USB Charger Cable (depending on purchase option)
- 1 or 2 x Belt Clip (depending on purchase option)
- 1 or 2 x Lanyard (depending on purchase option)
- 1 x Owner's Manual

Figure 3.1: Typical package contents.
4. Main Features
- Voice Recognition & Intelligent Noise Reduction: Easy to deal with noisy environments, ensuring clear sound quality and better communication.
- Encrypted Calls: Up to 32 key configurations for confidential communication, preventing eavesdropping and interference.
- Digital & Analog Compatibility: GMSK Digital + Analog modes, with analog frequency sweep function for matching other intercom devices.
- Wireless Cloning: Batch copying without the need for computer programming.
- Advanced Signal Processing: Supports non-standard CTCSS, frequency hopping, enhancing signal concealment and anti-interference ability.
- Rich Shortcut Operations: Two function keys combined for common manual setup functions.
- 30 Channel Memory: Supports both digital and analog channels.
- Customizable Side Buttons: Monitor, Power selection, Alarm function.
- CTCSS/DCS Support: 51 Groups of standard CTCSS, 105 groups of standard DCS, and non-standard analog CTCSS.
- Squelch Settings: 4 groups (Normally open, Normal, Strengthened, Strict).
- VOX Function: Voice-activated emission with 5-Level voice-activated level setting for hands-free operation.
- Channel Scan: Analog and digital channel scanning and addition.
- Power Selection: High and low transmit power options.
- Multi-language Support: Chinese and English language settings, with support for more small language reporting (Russian, French, Portuguese, Spanish, German).
- Type-C Charging: Convenient and fast charging.
- Playback Features: Playback frequency of current channel, playback current battery level.

Figure 4.1: Key features of the BAOFENG W31D.

Figure 4.2: Intelligent Noise Reduction for a more comfortable experience.
5. Main Controls and Parts of the Radio

Figure 5.1: Main controls and parts of the BAOFENG W31D.
- Antenna: For transmitting and receiving radio signals.
- PTT (Push-to-Talk): Press to transmit, release to receive.
- SK1 (+/Channel UP Key): Used for channel adjustment and other programmed functions.
- SK2 (-/Channel Down Key): Used for channel adjustment and other programmed functions.
- Battery Release Latch: Secures the battery pack.
- Type-C USB Charging Port: For charging the radio.
- Power Switch/Volume Control: Rotates to turn the radio on/off and adjust volume.
- LED Indicator: Red for transmitting (TX), Green for receiving (RX).
- Speaker: Outputs audio.
- Type-C Charging LED: Indicates charging status.
- External Speaker/Mic Jack: Allows connection of external devices like headsets or microphones.
5.1 LED Status Indications
The top LED helps identify the current radio status:
| LED Indication | Radio Status |
|---|---|
| Constant Red | Transmitting |
| Constant Green | Analog Receiving |
| Flashes Green | Analog Scan |
| Constant Yellow | Encryption Receiving |
| Flashes Yellow | Encryption Scan |
6. Setup
6.1 Battery Recharge
To charge the batteries in the radio:
- Insert the original adapter into an AC socket.
- Insert the adapter cable into the Type-C socket on the right side of the radio (open the protective cover).
- Ensure the Type-C socket is in good contact with the charging terminal. The indicator light on the top of the radio will turn orange, indicating charging has begun.
- A full charge typically takes approximately 2-5 hours. The indicator light on the top of the radio will turn off when charging is complete.
- Once fully charged, remove the cable from the Type-C port and close the protective cover.
Note: It is recommended to turn off your radio while it is being charged.

Figure 6.1: 1500mAh Battery and Type-C Charging.

Figure 6.2: Type-C USB Charging Port.
7. Operation
7.1 Power On/Off and Volume Adjustment
- To turn the radio on, rotate the [Power/Volume] knob clockwise.
- To adjust the volume level, rotate the [Power/Volume] knob clockwise to increase or counter-clockwise to decrease.
- To turn the radio off, rotate the [Power/Volume] knob counter-clockwise until you hear a mechanical “click”.
- If voice prompts are enabled, you will hear “Power on and channel number” upon turning on.
7.2 Select a Channel
The W31D can store up to 30 channels, supporting both analog and encrypted types.
- In standby mode, press the [+/SK1] or [-/SK2] keys to select a channel.
- If the voice prompt function is on, the channel number will be broadcast.
- If the channel is encrypted, it will be accompanied by “Encryption and channel number”.
- For communication, all radios in your group must be set to the same channel.
7.3 Making a Call
- Ensure all radios in your group are set to the same channel.
- (Optional) Press and hold the [+/SK1] key to enable the Monitor feature to check if the frequency is busy.
- Press and hold the [PTT] key to transmit. Speak into the microphone in a normal tone. The red LED indicator will be constantly on.
- Release the [PTT] key to receive.
Important: Only one user can transmit at a time. Avoid transmitting while receiving. Transmission consumes significant battery power, so use it sparingly.
7.4 Making an Encrypted Call
- Select an encryption channel.
- Press and hold the [PTT] key. The radio will be in transmitting state, and the red indicator light will be constantly on.
- Speak into the microphone in a normal tone.
- After releasing the [PTT] key, the yellow light briefly flashes once, indicating the radio is in an acceptable state. When receiving an encrypted call, the yellow indicator light remains on.
Note: For successful encrypted communication, all group members must be on the same channel and use the same encryption sequence (0-31).
7.5 Monitor Function
The Monitor feature opens the Squelch to hear weak signals. Ensure the side key function is defined as “Long Press Monitor” in the programming software.
- Press and hold the [+/SK1] key to activate the Monitor function.
7.6 One-touch Access to Battery Level
- In standby mode, press and hold the [-/SK2] key (Battery access). A voice prompt will announce the current battery level:
- “High battery level”: sufficient battery.
- “Medium battery level”: average battery.
- “Low power”: insufficient power, please charge immediately.
7.7 Channel Memory Information Access
- In standby mode, press and hold [+/SK1] and then briefly press [-/SK2]. The radio will broadcast parameter information for the current channel, such as transmit frequency, receive frequency, CTCSS/DCS, and transmit power.
7.8 Channel Scan
This function requires activation via optional programming software. Program at least two scanning channels before using.
7.8.1 Analog Scanning
- On channel 16, press and hold the [PTT] and [+/SK1] keys to turn on the radio and enter analog scan. The scan starts from the current channel, and the signal light flashes green.
- Press and hold the [+/SK1] key again to exit the scan.
- When scanning pauses on a channel, the green light illuminates. Pressing [PTT] will make a callback on the stay channel.
- To pause scanning, press [+/SK1]. The radio returns to the last received signal's channel for transmission. If no valid signal is received, it returns to the scanning start channel.
- Scanning stops when a signal is detected and resumes after 5 seconds of carrier signal loss. The voice prompts the scanned channel number.
7.8.2 Encryption Scanning
- On channel 14, press and hold the [PTT] and [+/SK1] keys to turn on the radio and enter encryption scan. The scan starts from the current channel, and the signal light flashes yellow.
- Press and hold the [+/SK1] key again to exit the scan.
- When scanning pauses on a channel, the yellow light illuminates.
- To pause scanning, press [+/SK1]. The radio returns to the last received signal's channel for transmission. If a valid signal is continuously received, it returns to the scanning start channel.
- Scanning stops when a signal is detected and resumes after 5 seconds of carrier signal loss. The voice prompts the scanned channel number.
7.9 VOX Function (Voice-Activated Transmission)
The VOX feature allows hands-free conversations without pressing PTT. Speak towards the microphone, and communication will activate automatically. VOX sensitivity can be adjusted in 5 levels (1-5) via programming software (Level 2 is default, 5 is lowest sensitivity).
- On channel 5, press and hold the [PTT] and [+/SK1] keys to turn on the radio. It will prompt “VOX on, welcome 5” to turn VOX on/off.
7.10 Wireless Frequency Copy (Quick Group Formation)
This feature allows quick replication of channel parameters from one radio (transmitter) to another (receiver).
- On channel 2, press and hold the [PTT] and [+/SK1] keys on both the transmitter and receiver to turn them on.
- The receiver and transmitter will prompt “beep” to enter wireless replication mode.
- On the transmitter, press the [PTT] key. The red light on the transmitter will remain on, and the green light on the receiver will automatically remain on.
- After all channel parameters are copied, the receiver will prompt “beep” twice and automatically restart.

Figure 7.1: Wireless Copy Frequency.

Figure 7.2: Wireless Frequency Copy Steps.
7.11 Quick Operation Radio (PTT + SK1 Combinations)
Without CPS programming software, you can perform the following quick operations:
- Channel 1: Press and hold [PTT] and [+/SK1] to turn on the radios; green light flashes for frequency scanning.
- Channel 2: Press and hold [PTT] and [+/SK1] to open radios for wireless copying/grouping.
- Channel 5: Press and hold [PTT] and [+/SK1] to turn on radio and toggle VOX function (voice prompt: VOX On or VOX Off).
- Channel 10: Press and hold [PTT] and [+/SK1] to turn on radio and toggle prompt voice function.
- Channel 15: Press and hold [PTT] and [+/SK1] to turn on radio and switch prompt language (Chinese/English).
- Channel 16: Press and hold [PTT] and [+/SK1] to turn on radio and toggle analog channel scanning function.
- Channel 14: Press and hold [PTT] and [+/SK1] to turn on radio and toggle encrypted channel scanning function.
8. Maintenance
8.1 General Care
- Do not clean the case with thinner or benzene. Use a soft, dry cloth to clean the case.
- If the transceiver is not being used for an extended period, turn it off and remove the battery pack for safety.
- Keep the terminals of the battery pack clean.
8.2 Battery Care
- Charge the battery pack within the recommended temperature range of +5 °C to +35 °C (+41 °F to +95 °F).
- Before discarding a worn battery pack, affix tape or similar material to its terminals to prevent short circuits.
9. Troubleshooting
This section addresses common issues you might encounter with your BAOFENG W31D Walkie Talkies.
- Radio does not turn on: Ensure the battery is properly installed and charged. Check if the power/volume knob is rotated clockwise sufficiently.
- Cannot transmit or receive: Verify that both radios are on the same channel and frequency. Check if the PTT button is functioning correctly. Ensure the antenna is securely attached.
- Poor audio quality or static: Check for obstructions between radios. Ensure you are within range. Adjust squelch settings if necessary.
- Battery not charging: Ensure the Type-C cable and adapter are properly connected. Check if the charging LED indicates charging. If the battery is externally damaged or deformed, do not use it.
- Wireless Copy Frequency fails: Ensure both radios are on channel 2 and follow the steps precisely. Make sure the transmitter is actively transmitting during the copy process.
- Programming issues: The W31D requires specific BAOFENG CPS software (V1D series) and a PL2303 chip-based programming cable. Generic software like CHIRP may not be compatible.
10. Technical Specifications
10.1 General
| Parameter | Value |
|---|---|
| Frequency Range | 410-469 MHz (FCC), *430-440 MHz (CE) |
| Working Temperature | -20°C to +55°C |
| Operating Voltage | 3.7 V |
| Operate Mode | Simplex |
| Dimensions (with antenna) | 114 x 60.5 x 32 mm |
| Weight (Battery pack included) | 176 g |
| Antenna Impedance | 50Ω |
| Battery Capacity | 1500mAh (Li-Ion) |
| Work Time | 24 Hours |
| Standby Time | 30 Days |
10.2 Transmitter
| Parameter | Value |
|---|---|
| Frequency Stability | ±2.5 PPM |
| Output Power | ≤2W ERP |
| Max Frequency Deviation | ≤2.5 KHz |
| Audio Distortion | ≤3% |
| Adjacent Channel Power | < 60 dB |
10.3 Receiver
| Parameter | Value |
|---|---|
| RF Sensibility | <0.2 UV @ 20 dB SINAD |
| Audio Distortion | ≤3% |
| Audio Response | 300 Hz ÷ 3 KHz |
| Adjacent Channel Selectivity | Within European legal terms |
WARNING: Direct plug-in AC/DC power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.

Figure 10.1: Dimensions and key specifications.

Figure 10.2: Radio and Battery Specifications.
11. User Tips
- Programming Software: For PC programming, download the official BAOFENG CPS software (V1D series) from baofengradio.com (Support > Download > V1D). Note that CHIRP software is currently not compatible. A PL2303 chip-based programming cable is required.
- Scanning Shortcut: To initiate scanning, hold down the Channel 16 +/- keys and then turn on the radio.
- Battery Life: While rated for 1500mAh, some users have noted that actual battery performance might vary. Ensure a full charge for optimal range and standby time.
- Antenna and Audio: Some users have reported the antenna having high impedance and the speaker sound being of poor quality compared to other models. Consider using an external antenna if range is critical, and external headsets for improved audio clarity.
12. Warranty and Support
For any issues not covered in this manual, please contact your dealer or Alervites Customer Support. The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development.
Contact Information:
Quanzhou Getlike Ele-Technology Co., Ltd.
Address: No. 20 Longgaoshan, Pudang Village, Xiamei Town, Nan'an, Fujian, China. P 362302
Website: https://www.alervites.com
You can also refer to the official user manual PDF for additional details: User Manual (PDF)
13. Regulatory Information
13.1 FCC Regulations (Federal Communication Commission)
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications made to this device, not expressly approved by Alervites, could void the user's authority to operate this equipment.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
13.2 ISED Regulations (Innovation, Science, and Economic Development Canada)
The operation of your Alervites radio is subject to the Radiocommunications Act and must comply with rules and regulations of the Federal Government's department of Innovation, Science, and Economic Development Canada (ISED). ISED requires that all operators using Private Land Mobile frequencies obtain a radio license before operating their equipment.
This radio transmitter has been approved by Innovation, Science, and Economic Development Canada (ISED) to operate with Alervites-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
13.3 EU Regulatory Conformance
As certified by the qualified laboratory, the product is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC (2014/53/EU). All applicable EU regulations are regarded (2016/66/EC, 2011/65/EU, 2012/19/EU). This information is applicable to EU countries only.
13.4 European Union (EU) and United Kingdom (UK) Waste of Electrical and Electronic Equipment (WEEE) Directive

The European Union's WEEE directive and the UK's WEEE regulation require that products sold into EU countries and the UK must have the crossed-out wheelie bin label on the product (or the package). This symbol indicates that customers and end users in EU and UK countries should not dispose of electronic and electrical equipment or accessories as household waste. Customers or end users should contact their local equipment supplier representative or service center for information about the waste collection system in their country.
13.5 Disclaimer
No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company. We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or completeness of the third-party products and contents involved in this manual.