AnyTone AT-5189

Contents

AnyTone AT-5189 Mobile Radio

User Instruction Manual

1. Introduction

The AnyTone AT-5189 is a versatile VHF/UHF mobile radio designed for reliable communication. This manual provides essential information for the proper setup, operation, and maintenance of your device. Please read it thoroughly before using the radio.

AnyTone AT-5189 Mobile Radio with microphone

Figure 1: AnyTone AT-5189 Mobile Radio with connected microphone.

Key features include 250 programmable channels, wide frequency coverage, and various signaling capabilities such as CTCSS, DCS, DTMF, 2Tone, and 5Tone encode/decode. It also supports PTT ID and ANI functions for enhanced communication management.

2. Setup Guide

2.1 Unboxing and Inspection

Carefully unpack the radio and all accessories. Verify that all components are present and undamaged. The standard package typically includes:

  • AnyTone AT-5189 Mobile Radio Unit
  • Handheld Microphone (QHM-02)
  • DC Power Cable
  • Mounting Bracket and Hardware
  • User Manual (this document)
AnyTone AT-5189 Mobile Radio in its retail packaging

Figure 2: AnyTone AT-5189 Mobile Radio in its retail packaging.

2.2 Power Connection

The AT-5189 operates on 13.8V DC ±15%. Connect the supplied DC power cable to the radio's power input port on the rear panel. Ensure the red wire connects to the positive (+) terminal and the black wire to the negative (-) terminal of your power source. Incorrect polarity can damage the radio.

2.3 Antenna Connection

Connect a suitable VHF/UHF antenna to the SO-239 antenna connector on the rear of the radio. Ensure the connection is secure to prevent signal loss and potential damage to the radio's transmitter.

Rear view of AnyTone AT-5189 Mobile Radio showing antenna and power connections

Figure 3: Rear panel connections for antenna and power.

2.4 Microphone Connection

Plug the microphone cable into the microphone jack located on the front panel of the radio.

Close-up of the QHM-02 microphone for AnyTone AT-5189

Figure 4: QHM-02 Handheld Microphone.

2.5 Mounting the Radio

Use the provided mounting bracket and hardware to securely install the radio in your desired location (e.g., vehicle dashboard, desk). Ensure adequate ventilation around the unit to prevent overheating.

Front view of AnyTone AT-5189 Mobile Radio mounted on its bracket

Figure 5: AT-5189 mounted using the included bracket.

3. Operating Instructions

3.1 Power On/Off

Turn the volume knob clockwise to power on the radio. Turn it counter-clockwise until it clicks to power off.

3.2 Volume Control

Adjust the volume knob to your desired listening level.

3.3 Channel Selection

The AT-5189 supports 250 channels. Use the channel selector knob or the UP/DOWN buttons on the microphone to navigate through the channels. Each channel can be named with up to 32 characters for easy identification.

3.4 Squelch Control (SQ/C)

The squelch function mutes the speaker when no signal is present. Press the 'SQ/C' button to adjust the squelch level. Higher levels require stronger signals to open the squelch. The radio supports Carrier, CTCSS, DCS, 5Tone, 2Tone, and DTMF squelch types.

3.5 Transmit and Receive

To transmit, press and hold the Push-To-Talk (PTT) button on the microphone. Speak clearly into the microphone. Release the PTT button to receive.

3.6 Calling Functions

The radio supports various calling modes:

  • Single Call: Direct communication with a specific radio.
  • Group Call: Communication with a predefined group of radios.
  • Selective Call: Allows calling specific radios within a group.
  • Emergency Call: For urgent situations, typically pre-programmed.

Refer to the full programming software manual for detailed setup of these functions.

3.7 Scanning (SCAN)

Press the 'SCAN' button to activate channel scanning. The radio will cycle through programmed channels until a signal is detected. Press 'SCAN' again to stop.

3.8 PTT ID / ANI Function

The PTT ID (Push-To-Talk Identification) and ANI (Automatic Number Identification) features allow your radio's unique ID to be transmitted when you press or release the PTT button. This aids in identifying the transmitting station.

3.9 Function (FUNC) Button

The 'FUNC' button is used to access secondary functions or menu options. Press 'FUNC' followed by another key to activate its secondary purpose.

Video 1: AnyTone AT-5189 Mobile Radio Product Overview.

4. Maintenance

4.1 Cleaning

Clean the radio's exterior with a soft, dry cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the casing and display.

4.2 Environmental Considerations

Operate the radio within the specified temperature range of -20°C to +60°C (-4°F to +140°F). Avoid exposing the radio to extreme temperatures, direct sunlight for prolonged periods, or excessive moisture.

4.3 Antenna Care

Regularly inspect your antenna and its connection for any signs of wear or damage. A properly maintained antenna is crucial for optimal radio performance and to prevent damage to the radio's final amplifier stage.

5. Troubleshooting

5.1 No Power

  • Check the DC power cable connection to both the radio and the power source.
  • Verify the power source is providing 13.8V DC and that its fuse is intact.
  • Ensure the volume knob is turned clockwise past the 'off' position.

5.2 No Reception or Transmission

  • Check the antenna connection.
  • Verify that the correct frequency/channel is selected.
  • Adjust the squelch level (SQ/C). If it's set too high, weak signals may not open the squelch.
  • Ensure the microphone is properly connected.

5.3 Poor Audio Quality

  • Check the microphone connection.
  • Adjust the volume level.
  • Ensure the squelch level is not too low, which can allow static to be heard.

5.4 Interference

  • Adjust the squelch level.
  • Check for nearby electronic devices that might be causing interference.
  • Consider using CTCSS/DCS tones to filter out unwanted signals.

6. Specifications

CategoryParameterSpecification
GeneralFrequency RangeHF: 33-49MHz, 66-88MHz
VHF: 136-174MHz, 245-246MHz
UHF: 400-490MHz
Number of Channels250 channels
Channel Spacing25KHz (Wide Band), 20KHz (Middle Band), 12.5KHz (Narrow Band)
Phase-locked Step5KHz, 6.25KHz
Operating Voltage13.8V DC ±15%
SquelchCarrier/CTCSS/DCS/5Tone/2Tone/DTMF
Frequency Stability±2.5ppm
Operating Temperature-20°C to +60°C (-4°F to +140°F)
Dimensions (WxHxD)160 x 155 x 40mm
Weight1Kg
Receiver (ETSI EN 300 086 standard testing)Sensitivity (12dB Sinad)Wide Band: ≤0.2μV, Narrow Band: ≤0.25μV
Adjacent Channel SelectivityWide Band: ≥70dB, Narrow Band: ≥60dB
IntermodulationWide Band: ≥65dB, Narrow Band: ≥60dB
Spurious Rejection≥70dB
Audio ResponseWide Band: +1~-3dB (0.3~3KHz), Narrow Band: +1~-3dB (0.3~2.55KHz)
Hum & NoiseWide Band: ≥45dB, Narrow Band: ≥40dB
Audio Distortion≤5%
Audio Power Output≥2W@10%
Transmitter (ETSI EN 300 086 standard testing)Power OutputVHF: 60W/25W/10W, UHF: 45W/25W/10W
ModulationWide Band: 16KΦF3E, Narrow Band: 11KΦF3E
Adjacent Channel PowerWide Band: ≥70dB, Narrow Band: ≥60dB
Hum & NoiseWide Band: ≥40dB, Narrow Band: ≥36dB
Spurious Emission≥60dB
Audio ResponseWide Band: +1~-3dB (0.3~3KHz), Narrow Band: +1~-3dB (0.3~2.55KHz)
Audio Distortion≤5%

7. User Tips

  • Antenna Tuning: For optimal performance and to prevent damage, ensure your antenna is properly tuned for the operating frequencies. An SWR meter can help verify this.
  • Power Supply: Use a stable 13.8V DC power supply capable of providing sufficient current for the radio's maximum transmit power (e.g., 60W VHF requires approximately 12-15 Amps).
  • Programming Software: While basic operation is possible from the front panel, advanced features and channel programming are best managed using the dedicated programming software and a PC. This allows for easier customization of channels, tones, and other settings.
  • Ventilation: Mobile radios can generate heat during prolonged transmission. Always ensure adequate airflow around the unit, especially if mounted in an enclosed space.

8. Warranty and Support

8.1 Warranty Information

The AnyTone AT-5189 Mobile Radio comes with an 18-month warranty for the radio unit and a 6-month warranty for accessories. Please retain your proof of purchase for warranty claims.

8.2 Certifications

This product has obtained FCC, CE, and ROHS approvals, ensuring compliance with relevant safety and environmental standards.

Image displaying various product certifications including FCC, CE, and ROHS

Figure 6: Product Certifications.

8.3 Technical Support

For technical assistance or inquiries, please contact AnyTone support at sale16833@qxdz.cn.

© 2024 AnyTone. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.