1. Introduction
The Xinhai ZSW series vibrating feeder is a mechanical vibration type feeding equipment primarily designed for continuous and even feeding of materials. It incorporates a coarse screening function, making it suitable for various mining and mineral processing applications. This equipment is crucial for ensuring a steady material flow to downstream machinery such as crushers and ball mills, and can be integrated into automatic control systems for optimized production.
Key advantages of the ZSW vibrating feeder include its simple structure, convenient installation, stable vibration, reliable operation, and long service life. Its design facilitates easy maintenance and overhaul, contributing to efficient and uninterrupted processing.


2. Setup and Installation
Proper installation is critical for the safe and efficient operation of the vibrating feeder. While specific site requirements may vary, the following general steps should be followed:
- Foundation Preparation: Ensure a stable, level, and robust foundation capable of supporting the feeder's weight and dynamic loads during operation.
- Placement: Position the feeder according to the overall plant layout, ensuring proper alignment with upstream and downstream equipment (e.g., hoppers, crushers).
- Mounting: Securely bolt the feeder to the prepared foundation. Verify all mounting points are tightened to the manufacturer's specifications.
- Vibrator Assembly: The feeder utilizes a double eccentric shaft vibrator. Ensure it is correctly installed and aligned.
- Spring Supports: Verify that the spring supports are properly seated and provide adequate cushioning for vibration isolation.
- Electrical Connection: Connect the motor to the appropriate power supply. Ensure all electrical work is performed by a qualified electrician and complies with local electrical codes.
- Material Flow Path: Confirm that the material inlet and outlet are clear and properly aligned with the feeding and receiving equipment.
- Initial Inspection: Before first use, visually inspect all components for any signs of damage, loose connections, or obstructions.


3. Operating Instructions
The ZSW vibrating feeder is designed for continuous and even feeding, often incorporating a coarse screening process. Follow these general operating guidelines:
- Pre-Operation Checks:
- Ensure all safety guards are in place.
- Verify there are no foreign objects in the feeder trough.
- Check that all electrical connections are secure.
- Starting the Feeder:
- Start the feeder motor. Allow it to reach stable operating speed before introducing material.
- Gradually introduce material into the feeder trough.
- Adjusting Feed Rate:
- The feed rate can be adjusted by controlling the motor's frequency, especially if an optional variable frequency speed motor is installed. This allows for precise control of material output without frequent motor starts/stops.
- Monitor the material flow to ensure it is continuous and even, preventing blockages or surges.
- Coarse Screening:
- The baseplate of the feeding trough adopts a "blind plate + strip screen" form, which pre-screens smaller material pieces. Ensure the screened material is discharged properly.
- Stopping the Feeder:
- Stop the material flow first.
- Allow the feeder to run briefly to clear any remaining material from the trough.
- Turn off the feeder motor.
4. Maintenance
Regular maintenance ensures the longevity and optimal performance of your ZSW vibrating feeder. The design emphasizes ease of maintenance and overhaul.
Daily Checks:
- Inspect for any unusual noises or vibrations.
- Check for loose bolts, especially on the vibrator and mounting points.
- Ensure the feeder trough is free from excessive material buildup.
Weekly/Monthly Checks:
- Lubrication: Check and replenish lubricant in the vibrator bearings as per manufacturer guidelines.
- Wear Parts: Inspect the feeder trough and screen bars for wear. Replace worn parts to maintain feeding efficiency and screening quality.
- Springs: Examine the spring supports for damage or fatigue. Replace any compromised springs.
- Motor: Check the motor for overheating, unusual sounds, and proper ventilation.
- Belt Drive (if applicable): Inspect the V-belt for tension and wear. Adjust or replace as necessary.
Annual Overhaul:
- Conduct a thorough inspection of all structural components.
- Disassemble and inspect vibrator bearings, replacing if necessary.
- Repaint any areas showing rust or corrosion to protect the equipment.
5. Troubleshooting
This section provides general guidance for common issues. For complex problems, contact technical support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Uneven material flow or blockage | Incorrect feed rate setting, material bridging, worn trough liner | Adjust motor frequency/feed rate, clear blockages, inspect and replace worn liners. |
| Excessive noise or vibration | Loose mounting bolts, worn vibrator bearings, damaged springs, unbalanced vibrator | Tighten all bolts, inspect and replace bearings/springs, consult technician for vibrator balancing. |
| Motor overheating or failure to start | Electrical issue, motor overload, mechanical obstruction, worn motor bearings | Check power supply and connections, reduce load, clear obstructions, inspect motor. Consult electrician. |
| Poor screening efficiency | Worn screen bars, incorrect vibration amplitude, material properties | Inspect and replace screen bars, verify vibrator settings, adjust material input. |
6. Specifications
The Xinhai ZSW series vibrating feeders are available in various models, each with specific dimensions and capacities. Below is a general specification table:

| Model | Trough Size (mm) | Max Feed Size (mm) | Feeding Capacity (t/h) | Eccentric Shaft Speed (r/min) | Motor Power (kW) | Weight (kg) |
|---|---|---|---|---|---|---|
| ZSW-380×95 | 3800×950 | 500 | 96-160 | 800 | 11 | 4082 |
| ZSW-420×110 | 4200×1100 | 580 | 120-240 | 800 | 15 | 4149 |
| ZSW-490×960 | 4900×960 | 500 | 120-240 | 800 | 15 | 5351 |
| ZSW-490×110 | 4900×1100 | 630 | 120-280 | 800 | 15 | 5352 |
| ZSW-590×110 | 5900×1100 | 630 | 350-500 | 800 | 22 | 6130 |
| ZSW-600×130 | 6000×1300 | 750 | 400-560 | 800 | 22 | 7800 |
Other Properties:
- Origin: Mainland China
- Place of Origin: Yantai
- Item Number: glj2012021
- Alias: Feeder
7. User Tips
While no specific user reviews or Q&A were provided for this model, general tips for operating industrial vibrating feeders include:
- Always ensure the feeder is empty before starting or stopping to prevent unnecessary strain on the motor and vibrator.
- Regularly check the condition of the rubber or spring elements that support the feeder trough, as these are crucial for effective vibration and isolation.
- When adjusting the feed rate, make small, incremental changes and observe the material flow to avoid overfeeding or underfeeding the downstream equipment.
- Pay attention to the sound of the machine; any sudden changes in noise level can indicate a developing issue.
8. Warranty and Support
For warranty information, technical support, or any inquiries regarding your Xinhai ZSW series vibrating feeder, please contact the seller directly. Ensure you have your model number and any relevant purchase details ready.
Contact Information:
- Telephone: +8615273166040
- E-mail: QinyongTrading126.com
- WhatsApp: +8615273166040