1. Introduction
Thank you for choosing the Haytrix M6C E-Bike LCD Computer. This digital display unit is designed to enhance your electric bicycle riding experience by providing essential information such as speed, mileage, battery status, and more. Please read this manual carefully before installation and use to ensure proper operation and longevity of your device.
2. Product Features
- Advanced Color LCD Display: Horizontal mid-mounted VA color LCD for vivid and dynamic information display.
- Comprehensive Metrics: Shows battery indicators, walk mode, PAS level, current speed, trip/total odometer, trip time, metric/imperial units, and error warnings.
- USB Charging Interface: Equipped with a USB port (5V/500mA) for emergency charging of mobile phones or other small devices.
- Multiple PAS Modes: Supports 5 levels of Pedal Assist System (PAS) for varied riding experiences.
- Robust Compatibility: Compatible with 24V, 36V, 48V, and 60V e-bike systems.
- Standard Communication Protocol: Utilizes the UART 2 communication protocol.
3. Specifications
| Parameter | Description |
|---|---|
| Product Name | M6C Cycling Speed Odometer |
| Dimensions | 98.1mm x 61.9mm x 24.6mm |
| Functions | Battery Indicators, Walk, PAS level, Speed, Trip/ODO, Trip time, Mile/KM, Error warning |
| Communication | UART 2 Protocol |
| Compatible Handlebar Sizes | 22.2mm / 25.4mm / 28.6mm / 31.8mm |
| Compatible Voltage | 24V / 36V / 48V / 60V |
| USB Charging Output | 5V / 500mA |
| Certifications | CE, RoHS, IP65, SGS |
4. Installation Process
Follow these steps to correctly install your M6C E-Bike LCD Computer:
- Secure the display bracket to your e-bike's handlebar.
- Insert the M6C display into the bracket.
- Tighten the bracket screws to ensure the display is firmly in place.
- Connect the display's cable to the corresponding e-bike wiring harness.
- Ensure all connections are secure and waterproof.
- Verify the display powers on and functions correctly.
5. Operating Instructions
5.1 Basic Operation
The M6C display provides real-time information and allows control over various e-bike functions. Power on your e-bike, and the display will activate. Use the control buttons (typically + and -) to navigate through different display modes and adjust settings.
5.2 Changing Speed Settings
To adjust the speed settings on your M6C display:
- Long press the '+' and '-' keys simultaneously to enter the menu.
- Short press the power button to navigate to 'P08' setting.
- Use the '+' key to set your desired speed value.
- Once adjusted, long press the '+' and '-' keys again to save the changes and exit the menu.
6. Troubleshooting
If you encounter issues with your M6C display, refer to the following common problems and solutions:
6.1 E10 Error Display
If the display shows 'E10' after connection, it typically indicates one of two issues:
- Incompatible Communication Protocol: The communication protocol between the M6C display and your e-bike's controller may not be compatible. The M6C specifically uses the UART 2 protocol.
- Vehicle System Malfunction: The overall condition of the vehicle might be poor, affecting components like the boost controller, throttle, or motor. This can lead to communication failure with the display.
Solution: Verify that your e-bike's controller uses the UART 2 protocol. If the protocol is correct, inspect other e-bike components for any faults or damage that might interfere with communication.
6.2 Speed Limit Issues
The ability to lift a speed limit depends on where the limitation is imposed:
- If the speed is limited by the e-bike's controller, the display cannot override this setting.
- If the speed limit is imposed by the display itself, it can typically be adjusted through the display's settings menu (refer to Section 5.2).
Solution: Determine if your e-bike's speed limit is controlled by the display or the controller. Consult your e-bike's manual or manufacturer for clarification.
7. User Tips
- Protocol Verification: Before purchasing or installing, always confirm that your e-bike's controller uses the UART 2 communication protocol. You can check your controller's manual or contact its seller.
- Voltage Compatibility: The M6C supports 24V/36V/48V/60V systems. Ensure your e-bike's voltage matches this range for proper function.
- Bluetooth Connectivity: Some Haytrix models (e.g., H8, M5C-2) support Bluetooth for mobile app connection. The M6C does not explicitly state Bluetooth support in the provided information, so assume it does not unless specified otherwise by the seller.
- Speed Limit Customization: While the standard version does not support an immediate 25 km/h speed limit, specially customized versions might. Inquire with the seller if this feature is critical for your use.
8. Important Notices
- Protocol Mismatch: The product protocol is UART 2. If the protocols do not match, the product may not work properly.
- Bike Conversion Kits: Inappropriate interface replacement when using a bike conversion kit may affect the normal use of the display screen. Ensure correct wiring and compatibility.
9. Certifications
The Haytrix M6C E-Bike LCD Computer has obtained multiple certifications, ensuring quality and safety standards:
- CE (Conformité Européenne)
- RoHS (Restriction of Hazardous Substances)
- IP65 (Ingress Protection rating for dust and water resistance)
- SGS (Société Générale de Surveillance)
