1. Introduction
Thank you for choosing the GAHADA LED Strip Light. This product is a power-free IC rectifier double-sided adhesive light strip, designed for convenient use and easy installation in various indoor and outdoor settings. It is ideal for engineering decoration, providing versatile and efficient lighting solutions.
2. Safety Information
- Ensure the input voltage matches the product specification (AC220-240V) to prevent damage and ensure safety.
- Do not power on the LED strip while it is still coiled. Always expand the strip completely before connecting to power to prevent overheating, melting, and potential safety hazards.
- Installation should be performed by a qualified professional if you are unsure about electrical connections.
- Keep the product away from flammable materials.
- Do not submerge the product in water unless explicitly stated for specific waterproof ratings beyond IP65. While IP65 is waterproof, it is not designed for prolonged submersion.
- Avoid looking directly at the illuminated LEDs for extended periods, as this may cause eye strain.
3. Package Contents
Please check the package for the following items:
- 1 x GAHADA LED Strip Light (selected length and color temperature)
- 1 x EU Plug (with or without switch, depending on your selection)
4. Product Overview
The GAHADA LED Strip Light features SMD2835 lamp beads, providing bright and uniform illumination. It includes an integrated IC rectifier for direct connection to AC220-240V power, eliminating the need for external rectifiers. The strip is IP65 waterproof, making it suitable for various environments. A double-sided adhesive backing allows for easy and secure installation.
5. Setup Instructions
Follow these steps to set up your GAHADA LED Strip Light:
- Prepare the Surface: Ensure the installation surface is clean, dry, and smooth for optimal adhesion of the double-sided tape.
- Measure and Cut (if necessary): Measure the desired length for your installation. The LED strip can be cut every 10cm at designated marks. Use sharp scissors to ensure a clean cut.
- Connect the Power Plug:
- Locate the light strip and the snap connector on the EU plug.
- Align the positive and negative terminals of the LED strip with the pins inside the snap connector.
- Press the snap connector firmly to secure the connection. Ensure the connection is complete and tight.
- Unroll the Strip: Completely unroll the LED strip from its coil. This is crucial to prevent overheating.
- Mount the Strip: Peel off the protective backing from the double-sided adhesive tape on the reverse side of the LED strip. Carefully press the strip onto your desired surface, ensuring it adheres evenly.
- Connect to Power: Once the strip is fully unrolled and mounted, plug the EU plug into a compatible AC220-240V power outlet.
6. Operating Instructions
Once properly installed and connected to power:
- Turning On/Off: If your EU plug includes a switch, use it to turn the LED strip on or off. For plugs without a switch, connect/disconnect from the power outlet to control the light.
- Color Temperature: The LED strip is available in White Light (6000-6500K), Natural White (4000-4500K), and Warm White (3000-3500K). The selected color temperature is fixed and cannot be changed during operation.
7. Maintenance
- Cleaning: Disconnect the power before cleaning. Use a soft, dry cloth to gently wipe the LED strip. Do not use harsh chemicals or abrasive cleaners.
- Inspection: Periodically check the strip for any signs of damage, loose connections, or wear.
- Storage: If storing the LED strip, ensure it is clean and dry. Coil it loosely and store in a cool, dry place away from direct sunlight.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| LED strip does not light up | No power, loose connection, incorrect polarity, damaged strip/plug. | Check power outlet, ensure plug is firmly connected, verify correct polarity in snap connector, inspect strip for visible damage. |
| Part of the strip is not lighting | Damage to a section, improper cut. | Inspect the non-lighting section for physical damage or improper cutting. If cut, ensure the cut was made at the designated mark. |
| Strip is overheating | Strip is coiled or not fully expanded when powered on. | Immediately disconnect power. Ensure the strip is fully unrolled and has adequate ventilation. Never operate while coiled. |
| Adhesive not sticking | Surface not clean/dry, unsuitable surface material. | Clean and dry the surface thoroughly. For rough or porous surfaces, consider using additional mounting clips or stronger adhesive. |
9. Specifications
| Feature | Specification |
|---|---|
| Brand Name | GAHADA |
| Model Number | LED557 |
| Item Type | Strip |
| Strip Type | SMD |
| LED Chip Model | SMD2835 |
| LED Chip Brand | Epistar |
| LEDs Number/M | 120LEDs/m |
| Voltage | 220 V |
| Nominal Voltage | 220V |
| Power Source | AC |
| Color Temperature (K) | 3000-6000K (Warm White, Natural White, White Light options) |
| Luminous Flux | <60 |
| Waterproof | Yes (IP65) |
| Cuttable Length | 10cm |
| Strip Dimensions | W10mm x H4mm |
| Power Generation | light |
| Is Batteries Included | No |
| Certification | CE, ROHS |
| Occasion | LIVING ROOM (suitable for various indoor/outdoor applications) |
| Origin | Mainland China |
10. User Tips
- For long runs, ensure the power plug is capable of driving the entire length. One plug can typically drive up to 40 meters of this LED strip.
- When installing in corners or around curves, avoid sharp bends to prevent damage to the LED strip and ensure consistent light output.
- Consider using aluminum channels for a more professional finish, better heat dissipation, and added protection, especially in high-traffic areas.
- If using the strip outdoors, ensure all connections are properly sealed and protected from direct exposure to heavy rain or prolonged moisture, despite the IP65 rating.
11. Frequently Asked Questions (FAQ)
- Q: Can I connect multiple strips together?
A: Yes, you can connect multiple strips up to a total length of approximately 40 meters using a single EU plug. Ensure connections are secure. - Q: Is the adhesive strong enough for all surfaces?
A: The strip comes with double-sided adhesive. For best results, apply to clean, dry, and smooth surfaces. For textured or outdoor surfaces, additional clips or stronger adhesive may be required. - Q: How do I ensure the strip doesn't overheat?
A: Always unroll the entire length of the LED strip before plugging it into power. Operating a coiled strip can cause severe overheating and damage. - Q: Can this strip be used with a dimmer?
A: The product description does not specify dimmer compatibility. Using an incompatible dimmer may damage the strip. Consult a qualified electrician for dimmer integration.
12. Warranty and Support
For warranty information and customer support, please refer to the seller's policies or contact the GAHADA LED Lighting Store directly. Keep your purchase receipt as proof of purchase.
