ANDELI MCT-416P

Contents

ANDELI MCT-416P 7-in-1 Multifunctional Welder User Manual

Model: MCT-416P

1. Introduction

The ANDELI MCT-416P is a versatile 7-in-1 multifunctional welding machine designed for a wide range of welding and cutting applications. It supports Aluminum MIG, CUT (Plasma Cutting), MIG (CO2/MIX/FLUX), TIG (HF), COLD welding, PULSE welding, and MMA (Stick) welding. This manual provides essential information for the safe and efficient operation and maintenance of your welder.

Front view of the ANDELI MCT-416P 7-in-1 Multifunctional Welder
Figure 1: Front view of the MCT-416P Welder
Diagram showing the 6-in-1 welding and cutting functions: HF CUT, PULSE MIG, SYN MIG, HF TIG, MAN MIG, MMA
Figure 2: Overview of the 6-in-1 Multifunctional Welder capabilities.

2. Safety Precautions

Always observe the following safety precautions to prevent injury and damage to the equipment:

  • Ensure proper ventilation in the work area to avoid inhaling fumes.
  • Wear appropriate personal protective equipment (PPE), including welding helmet, gloves, and protective clothing.
  • Do not operate the machine in damp or wet conditions.
  • Ensure the machine is properly grounded.
  • Disconnect power before performing any maintenance or changing accessories.
  • Keep children and unauthorized personnel away from the welding area.
  • The transparent screen shield provides physical protection against sparks, splatter, scratches, and impacts. Ensure it is in place during operation.
Close-up of the transparent screen shield on the welder's control panel, showing protection from sparks.
Figure 3: Transparent Screen Shield for panel protection.

3. Package Contents

Verify that all items are present in your package:

  • MCT-416P Welder (with US plug)
  • Ground clamp
  • Aluminum welding torch (3M) x 1
  • MIG torch x 1
  • CUT torch PT-31 x 1
  • TIG torch WP-9F x 1
  • Gas pipe (3M)
  • Air pressure regulator
  • Hose clamp x 2
  • Tungsten electrode x 10
  • Tip x 10
  • Electrode x 10

4. Setup

4.1 Machine Overview

Diagram showing the machine overview with numbered components: 1. Parameter Button, 2. Torch Modes Button, 3. Voltage Adjust Knob, 4. Main Menu Function Button, 5. Wire Diameter Selection Button, 6. Weld Material Selection Button, 7. Amps Parameters Adjust Knob, 8. EURO Connector for MIG Gun, 9. Control Switch Socket, 10. Positive (+) Output Terminal, 11. Negative (-) Output Terminal, 12. CUT Ground Clamp, 13. CUT/HF TIG Gun Connector, 14. Power Switch, 15. Power Input Cable with Plug, 16. Ground Pin, 17. Air Filter Regulator Connection, 18. Fan, 19. MIG Gas Connector, 20. CUT Gas/TIG Gas Connector.
Figure 4: Machine Overview and Component Identification.
  1. Parameter Button: Adjusts welding parameters.
  2. Torch Modes Button: Selects different torch modes.
  3. Voltage Adjust Knob: Controls welding voltage.
  4. Main Menu Function Button: Navigates main menu functions.
  5. Wire Diameter Selection Button: Selects wire diameter for MIG.
  6. Weld Material Selection Button: Chooses material type for welding.
  7. Amps Parameters Adjust Knob: Adjusts amperage.
  8. EURO Connector for MIG Gun: Connects MIG torch.
  9. Control Switch Socket: For remote control or foot pedal.
  10. Positive (+) Output Terminal: Positive welding output.
  11. Negative (-) Output Terminal: Negative welding output.
  12. CUT Ground Clamp: Connects ground for plasma cutting.
  13. CUT/HF TIG Gun Connector: Connects CUT or HF TIG torch.
  14. Power Switch: Turns the machine ON/OFF.
  15. Power Input Cable with Plug: Connects to power supply (AC110V-240V).
  16. Ground Pin: For grounding the machine.
  17. Air Filter Regulator Connection: Connects to air supply for plasma cutting.
  18. Fan: Cooling fan.
  19. MIG Gas Connector: Connects gas supply for MIG welding.
  20. CUT Gas/TIG Gas Connector: Connects gas supply for CUT or TIG welding.

4.2 Power Connection

  • Ensure the power switch (14) is in the OFF position.
  • Connect the power input cable (15) to a suitable AC110V-240V power outlet.
  • Ensure the machine is properly grounded using the ground pin (16).

4.3 Torch and Ground Clamp Connection

  • MIG Welding: Connect the MIG torch to the EURO Connector (8). Connect the ground clamp to the workpiece. Connect the MIG gas supply to the MIG Gas Connector (19).
  • TIG Welding: Connect the TIG torch (WP-9F) to the CUT/HF TIG Gun Connector (13). Connect the ground clamp to the workpiece. Connect the TIG gas supply (pure argon) to the CUT Gas/TIG Gas Connector (20).
  • MMA Welding: Connect the electrode holder to the Positive (+) Output Terminal (10) and the ground clamp to the Negative (-) Output Terminal (11), or vice-versa depending on electrode polarity requirements.
  • Plasma Cutting: Connect the CUT torch (PT-31) to the CUT/HF TIG Gun Connector (13). Connect the CUT ground clamp (12) to the workpiece. Connect the air supply via the Air Filter Regulator Connection (17) to the CUT Gas/TIG Gas Connector (20).

5. Operating Instructions

5.1 Control Panel Introduction

The 5-inch large screen provides enhanced visibility for settings. Refer to Figure 5 for control panel details.

Detailed view of the welder's control panel with numbered labels for: 1. Input Voltage, 2. MIG parameters adjustment, 3. Torch process methods, 4. Wire diameter selection, 5. Voltage display area / current display area, 6. MMA parameters adjustment, 7. Material/Gas Selection, 8. Modes Selection.
Figure 5: Control Panel Layout and Functions.
  1. Input Voltage: Displays the current input voltage (110V or 220V).
  2. MIG Parameters Adjustment: Knobs and buttons for fine-tuning MIG welding settings.
  3. Torch Process Methods: Selects between 2T, 4T, and Spot welding modes.
  4. Wire Diameter Selection: Sets the wire diameter for MIG welding.
  5. Voltage/Current Display Area: Shows real-time voltage and current readings.
  6. MMA Parameters Adjustment: Adjusts settings specific to MMA welding.
  7. Material/Gas Selection: Selects the type of material being welded and the shielding gas.
  8. Modes Selection: Toggles between different welding/cutting modes (MIG, TIG, MMA, CUT, COLD, PULSE).

5.2 Selecting a Welding/Cutting Mode

Use the "Modes Selection" (8) on the control panel to choose your desired process:

  • MIG (CO2/MIX/FLUX): For general MIG welding.
  • Aluminum MIG: Optimized for welding aluminum.
  • PULSE MIG: Provides enhanced control for advanced materials and thin metals, resulting in high aesthetics.
  • TIG (HF): High-Frequency TIG for precise control, ideal for thin metals and stainless steel.
  • COLD Welding: Suitable for thin stainless steel, thin steel, carbon steel, and other materials where low heat input is critical to prevent deformation or discoloration. Requires pure argon gas.
  • MMA (Stick): For robust, versatile welding in challenging environments.
  • CUT (Plasma Cutting): For high-speed, precise cutting of various metals.
Example of a Pulse MIG weld bead, showing a clean and consistent pattern.
Figure 6: Example of Pulse MIG Welding.
Example of an HF TIG weld on stainless steel, showing a clean and precise weld bead.
Figure 7: Example of HF TIG Welding.
Comparison of plasma cutting thickness at 110V (12mm/0.59 inch) and 220V (15mm/0.59 inch).
Figure 8: Plasma Cutting Capabilities at different voltages.

5.3 Torch Process Methods (2T/4T/Spot)

The welder offers different torch trigger modes:

Diagram explaining 2T Non-Self Lock, 4T Self-Lock, and Spot Welding modes.
Figure 9: Torch Process Methods.
  • 2T Non-Self Lock: Press and hold the trigger to weld, release to stop. Ideal for quick fixing and tack welding.
  • 4T Self-Lock: Press and release the trigger to start welding, press and release again to stop. Suitable for production welding, overhead/vertical positions, or critical welds requiring consistency.
  • Spot Welding: Provides fast, cost-effective, and durable joins with minimal distortion.

6. Maintenance

  • Regularly clean the exterior of the machine with a dry cloth.
  • Ensure the cooling fan (18) and air vents are free from dust and debris to prevent overheating.
  • Inspect all cables and connections for wear or damage before each use. Replace any damaged components immediately.
  • Keep the transparent screen shield clean for clear visibility of the control panel.
  • Store the welder in a dry, clean environment when not in use.

7. Troubleshooting

If you encounter issues with your ANDELI MCT-416P welder, refer to the following common troubleshooting steps:

  • No Power: Check the power input cable (15) connection and the power outlet. Ensure the power switch (14) is ON.
  • Poor Weld Quality: Verify correct parameter settings (voltage, amperage, wire speed, gas flow) for your material and process. Ensure proper grounding. Check for contaminated workpiece or consumables.
  • Arc Instability: Check electrode/torch connections, gas flow, and ensure consumables are not worn out.
  • Overheating: Ensure the fan (18) and vents are clear. Allow the machine to cool down if the thermal overload indicator is active.
  • Plasma Cutter Not Cutting: Check air pressure, nozzle, electrode, and ground clamp connection. Ensure correct cutting parameters are set.

For persistent issues, contact customer support.

8. Specifications

Table of specification parameters for the ANDELI MCT-416P Multi-process Welder, including voltage, current, duty cycle, and cutting thickness for various modes.
Figure 10: Detailed Specification Parameters.
ParameterValue
FunctionMIGMIG PULSECOLDTIGMMAHF CUT
Power Supply VoltageAC110V-240VAC220-240V (for HF CUT)
Frequency50/60Hz
Efficiency80-85%
Power Factor0.73-0.76
No-Load Voltage62V62-268V (for HF CUT)
Rated Input Power8.28.26.26N/A9.58.8
Rated Input Current37372928N/A4440
Cold Welding Time (MS)N/A1-200N/A
Cold Welding Interval (Hz)N/A0-10N/A
Pre-Flow TIME (S)N/A0-1N/A
Duty Cycle (30%)200A200A200AN/A200A200A200A50A
Duty Cycle (60%)141A141A141AN/A141A141A141A35A
Duty Cycle (100%)110A110A110AN/A110A110A110A27A
Cutting Thickness1-15mm0.4-10mm (for TIG)
Insulation ClassH
Protection ClassIP21S
CoolingFan
Dimension (MM)489 x 210 x 327
Weight23.0 kg

9. User Tips

  • Aluminum TIG Welding: The MCT-416P supports High-Frequency TIG welding, which is suitable for aluminum. Ensure you use pure argon gas for optimal results when TIG welding aluminum.
  • Cold Welding: For best results with Cold Welding, especially on thin materials where aesthetics are important, always use pure argon gas to prevent discoloration and deformation.
  • Voltage Selection: The machine automatically detects input voltage (110V-240V). Be aware that cutting thickness for plasma cutting may vary based on the input voltage (e.g., 12mm at 110V vs. 15mm at 220V).

10. Warranty and Support

The ANDELI MCT-416P welder comes with CE certification, ensuring compliance with European safety standards.

  • Warranty: A two-year warranty is provided, including free replacement parts.
  • Customer Service: For guidance or issues, you can contact the efficient customer service team.
  • Contact Information:
    • WhatsApp: +86 19943356840
    • E-mail: 3539977011@qq.com
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.