DTF Printer E2070

Contents

E2070 DTF Printer 60cm Dual-Head with Shake Powder Machine User Manual

Model: E2070

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your E2070 60cm Dual-Head DTF (Direct-to-Film) Printer with an integrated automatic shake powder and curing machine. This system is designed for high-quality textile printing, offering efficient and vibrant results on various fabrics.

Please read this manual thoroughly before operating the equipment to ensure safe and correct usage, and to achieve optimal printing performance.

2. Safety Information

Always observe the following safety precautions to prevent injury and damage to the equipment:

  • Ensure the printer is connected to a grounded power outlet with the correct voltage.
  • Do not operate the printer in areas with excessive dust, humidity, or extreme temperatures.
  • Keep all liquids, especially ink and cleaning solutions, away from electrical components.
  • Wear appropriate personal protective equipment (PPE) such as gloves and eye protection when handling inks and powder.
  • Ensure adequate ventilation in the work area to dissipate fumes from inks and curing processes.
  • Do not touch moving parts of the printer or shaker machine during operation.
  • Keep children and unauthorized personnel away from the equipment.
  • In case of emergency, immediately disconnect the power supply.

3. Package Contents

Upon receiving your E2070 DTF Printer system, please verify that all components are present and undamaged. The standard package typically includes:

  • E2070 60cm Dual-Head DTF Printer unit
  • Automatic Shake Powder and Curing Machine unit
  • Printer stand/legs
  • Ink tanks and initial set of DTF inks (CMYK + White)
  • DTF powder
  • DTF film roll
  • Power cables
  • USB data cable
  • Software installation media (CD/USB) or download instructions
  • Cleaning tools and maintenance kit
  • User Manual (this document)
E2070 DTF Printer and Shake Powder Machine system
Figure 3.1: Overview of the E2070 DTF Printer and Shake Powder Machine system.

4. Setup Guide

4.1 Unpacking and Placement

  • Carefully remove all components from their packaging.
  • Place the printer and shaker machine on a stable, level surface capable of supporting their weight. Ensure sufficient space around the units for operation and maintenance.
  • Assemble the printer stand according to the provided instructions.

4.2 Connecting the Units

  • Connect the printer unit to the shake powder machine unit as indicated in the assembly diagrams. This typically involves aligning the film output of the printer with the film input of the shaker.
  • Ensure all mechanical connections are secure.
Side view of DTF printer and shaker connected
Figure 4.2: Side view illustrating the connection between the DTF printer and the shake powder machine.

4.3 Power and Data Connections

  • Connect the power cables to the printer and shaker machine, then plug them into appropriate grounded electrical outlets.
  • Connect the USB data cable from the printer to your computer.

4.4 Software Installation

  • Insert the software installation media or follow the provided link to download the necessary drivers and RIP (Raster Image Processor) software.
  • Install the software on your computer, following the on-screen prompts.
  • Configure the printer settings within the RIP software according to your specific requirements and media type.

4.5 Ink Loading

  • Carefully fill the designated ink tanks with the corresponding DTF inks (Cyan, Magenta, Yellow, Black, White). Ensure no cross-contamination occurs.
  • Perform an initial ink prime cycle as instructed by the printer's control panel or software to fill the ink lines and printheads.
  • Regularly check ink levels and refill as needed.
Close-up of printer printheads and ink lines
Figure 4.5: Detailed view of the printhead assembly and ink delivery system.

4.6 Film and Powder Loading

  • Load a roll of DTF film onto the printer's film feeder, ensuring it is correctly aligned and tensioned.
  • Load the DTF powder into the shaker machine's powder reservoir.

5. Operating Instructions

5.1 Preparing Your Design

  • Create or import your design into the RIP software.
  • Adjust color profiles, print resolution, and print size as required.
  • Ensure a white underbase layer is correctly generated for printing on dark garments.

5.2 Printing Process

  1. Send the prepared design from the RIP software to the E2070 printer.
  2. The printer will print the design onto the DTF film, first the color layers, then the white underbase.
  3. As the film exits the printer, it will automatically feed into the shake powder machine.
  4. The shaker machine will evenly apply DTF adhesive powder to the wet ink. Excess powder will be removed.
  5. The film with applied powder then proceeds through the curing tunnel, where heat melts the adhesive powder onto the ink.
  6. Once cured, the film is ready for transfer to a garment using a heat press (heat press not included).
DTF film being printed and powdered
Figure 5.2: DTF film moving from the printer to the shake powder machine, showing the printing and powder application stages.
DTF film with powder entering curing tunnel
Figure 5.3: Curing process within the shake powder machine, where heat melts the adhesive powder.

5.3 Post-Printing

  • Once the film is cured, allow it to cool before handling.
  • Store cured films in a dry, cool place until ready for heat transfer.

6. Maintenance

Regular maintenance is crucial for the longevity and optimal performance of your DTF system.

6.1 Daily Maintenance

  • Perform a nozzle check and head cleaning cycle at the start of each printing session.
  • Wipe down the printhead surface and capping station with a lint-free cloth and cleaning solution.
  • Clean any ink residue from the film path and rollers.
  • Empty the waste ink tank.

6.2 Weekly Maintenance

  • Thoroughly clean the printhead and surrounding areas.
  • Inspect and clean the encoder strip and sensor.
  • Clean the powder application area and ensure no powder buildup obstructs movement.
  • Check and clean the curing tunnel heating elements if accessible and cooled.

6.3 Long-Term Storage

If the printer will be inactive for an extended period (more than a week), perform a printhead flush with cleaning solution to prevent ink from drying and clogging the nozzles. Consult the software or manufacturer's guidelines for specific procedures.

7. Troubleshooting

Problem Possible Cause Solution
Poor print quality (streaks, missing nozzles) Clogged printhead nozzles, low ink levels, incorrect print settings. Perform nozzle check and head cleaning. Refill ink tanks. Verify print settings in RIP software.
Film not feeding correctly Film misalignment, rollers dirty or worn, incorrect tension. Re-align film. Clean rollers. Adjust film tension.
Powder not adhering or clumping Ink not wet enough, incorrect powder application settings, high humidity. Check ink flow. Adjust powder shaker settings. Ensure low humidity in work area.
Curing issues (powder not melting) Insufficient heat, incorrect curing speed. Increase curing temperature or slow down film speed. Check heating elements.
Printer not recognized by computer Driver not installed, loose USB connection, printer off. Install/reinstall drivers. Check USB cable and connection. Ensure printer is powered on.

8. Specifications

Feature Detail
Model E2070 DTF Printer with Shake Powder Machine
Printhead Type Dual-Head (F1080-A1 / I3200-A1 options)
Printing Width 60 cm
Ink Type DTF Pigment Ink (CMYK + White)
Material Rubber (likely referring to specific components)
Origin Mainland China
Package Dimensions (L x W x H) 45 cm x 45 cm x 45 cm (approximate, for individual components)
Package Weight 20.0 kg (approximate, for individual components)

Note: Specifications are subject to change without prior notice. Please refer to the product packaging or official website for the most up-to-date information.

9. User Tips

  • Ventilation is Key: Always ensure your workspace is well-ventilated when operating the DTF printer and shaker, especially during the curing process, to manage fumes from inks and powder.
  • Regular Cleaning: Adhere strictly to the daily and weekly maintenance schedules. DTF systems require consistent cleaning to prevent printhead clogs and ensure consistent print quality.
  • Ink Agitation: If your white ink tank has an agitator, ensure it's functioning correctly to prevent pigment settling, which can lead to clogs.
  • Powder Management: Keep DTF powder dry and free from moisture. Store it in a sealed container when not in use to prevent clumping.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your vendor or the manufacturer directly. Keep your purchase receipt and product serial number handy when contacting support.

Contact Information:

  • Email: 89530960@qq.com
  • WhatsApp: +86 17343617351
General customer service message with contact details
Figure 10.1: Contact information for customer support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.