1. Introduction
This manual provides instructions for the proper installation, operation, and maintenance of DIVEDEER IP68 Metal Waterproof Cable Glands. These cable glands are designed to provide secure and waterproof cable entry into electrical enclosures, junction boxes, and other equipment, ensuring protection against dust, water, and strain relief for cables.
Figure 1: Various DIVEDEER Metal Waterproof Cable Glands and their application.
2. Product Features
- High Protection Rating: IP68 rated, offering excellent protection against dust and water ingress.
- Durable Construction: Made from stainless steel or copper nickel-plated brass for corrosion resistance and longevity.
- Strong Fixity: Internal buckle design and robust construction ensure strong fixation and strain relief for cables, preventing shifting and squeezing.
- Wide Cable Range: Available in various sizes (M6 to M16, PG7 to PG11) to accommodate different cable diameters (e.g., PG7 for 3-6.5mm cables, up to 14mm for larger models).
- Reliable Sealing: Features a built-in waterproof sealing ring for a reliable, non-leaking connection.
- Certifications: CE, Dot, RoHS, ISO9001, SGS certified for quality and safety.
- High Voltage Rating: Suitable for applications up to 1000V.
Figure 2: Illustrating the strong fixity and internal buckle design.
3. Installation Instructions
The DIVEDEER cable glands utilize an external thread connection for easy and secure installation. Follow these steps for proper assembly:
- Prepare the Enclosure: Ensure the mounting hole in your enclosure matches the thread size of the cable gland (e.g., M12, PG7). The surface around the hole should be clean and flat to ensure a good seal.
- Disassemble the Gland: Unscrew the cap nut from the main body of the cable gland. The gland typically consists of a cap nut, sealing ring, claw, main body, and a washer.
- Insert the Main Body: Insert the threaded main body of the cable gland through the prepared hole from the outside of the enclosure.
- Secure with Washer and Nut: Place the washer (if provided) and then the lock nut onto the threaded main body from the inside of the enclosure. Tighten the lock nut to secure the gland to the enclosure.
- Prepare the Cable: Strip the outer jacket of the cable to the appropriate length, exposing the inner conductors. Ensure the cable's outer diameter falls within the specified cable range for your chosen gland size.
- Insert the Cable: Pass the prepared cable through the cap nut, then through the sealing ring and the claw, and finally into the main body of the cable gland.
- Tighten the Cap Nut: Hand-tighten the cap nut onto the main body. Then, use an appropriate wrench to tighten it further until the sealing ring compresses firmly around the cable, providing a waterproof seal and strain relief. Do not overtighten, as this can damage the sealing ring or the cable.
Figure 3: Components of a metal waterproof connector.
4. Operation
Once properly installed, the DIVEDEER cable gland operates passively by maintaining a secure, waterproof, and dustproof seal around the cable entry point. It provides essential strain relief, preventing the cable from being pulled out or damaged due to tension or vibration. No active operation is required from the user after installation.
Figure 4: Demonstrating strong waterproof and non-leaking properties.
5. Maintenance
DIVEDEER metal cable glands are designed for low maintenance due to their robust construction. However, periodic inspection is recommended to ensure continued performance:
- Visual Inspection: Regularly check the cable gland for any signs of physical damage, corrosion, or wear on the sealing ring.
- Tightness Check: Periodically verify that the cap nut and lock nut remain securely tightened. If any loosening is detected, re-tighten them to the appropriate torque.
- Environmental Factors: In harsh environments (e.g., extreme temperatures, chemical exposure), more frequent inspections may be necessary.
- Cleaning: If necessary, clean the exterior of the cable gland with a damp cloth. Avoid using harsh chemicals that could degrade the material or sealing components.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water/Dust Ingress | Incorrect cable gland size for cable diameter; insufficient tightening of cap nut; damaged or worn sealing ring; improper installation. | Ensure cable diameter matches gland's range. Re-tighten cap nut. Inspect and replace sealing ring if damaged. Re-install following instructions carefully. |
| Cable Slippage/Lack of Strain Relief | Cap nut not tightened sufficiently; cable diameter too small for gland. | Tighten cap nut firmly. Use a smaller cable gland size appropriate for the cable. |
| Gland Loosens Over Time | Insufficient tightening of lock nut; vibration. | Ensure lock nut is securely tightened to the enclosure. Consider using thread-locking compound if vibration is severe. |
7. Specifications
| Attribute | Detail |
|---|---|
| Brand Name | DIVEDEER |
| Model Numbers | M6, M8, M10, M12, M14, M16, PG7, PG9, PG11 |
| Material | Stainless Steel or Copper Nickel Plated Brass |
| Protection Rating | IP68 |
| Voltage Rating | 1000 V |
| Certifications | CE, Dot, RoHS, ISO9001, SGS |
| Installation Method | External Thread Connection |
| Cable Range (Example PG7) | 3-6.5mm (Varies by specific model) |
| Origin | Mainland China |
Figure 5: PG7 Cable Gland Dimensions and Specifications.
8. User Tips
- Always select the correct cable gland size that matches both the cable's outer diameter and the enclosure's mounting hole. A mismatch can compromise the IP rating and strain relief.
- When installing, ensure the sealing ring is correctly seated and not twisted or pinched, as this is critical for a waterproof seal.
- For applications requiring extreme vibration resistance, consider adding a small amount of thread-locking fluid to the lock nut threads (on the enclosure side) after tightening.
- Keep a variety of cable gland sizes on hand if you frequently work with different cable types to ensure you always have the right fit.
9. Warranty and Support
For any questions regarding the DIVEDEER IP68 Metal Waterproof Cable Glands, or for technical support, please contact your retailer or the manufacturer directly. Please retain your proof of purchase for warranty claims.