Jessinie ESPC3 Series

Contents

ESPC3 Series Wi-Fi Module Instruction Manual

Brand: Jessinie | Model: ESPC3 Series

1. Introduction

This manual provides essential information for the setup, operation, and maintenance of the Jessinie ESPC3 Series Wi-Fi Modules. These modules are compact, powerful 32-bit RISC-V MCUs featuring integrated BLE 5.0 and Wi-Fi connectivity with an onboard antenna, making them ideal for a wide range of IoT and embedded applications.

2. Safety Information

  • Always handle electronic components with care to prevent electrostatic discharge (ESD).
  • Ensure proper power supply voltage as specified in the technical specifications to avoid damage.
  • Do not expose the module to extreme temperatures, humidity, or corrosive environments.
  • Soldering should be performed by experienced personnel in a well-ventilated area.

3. Product Overview

The ESPC3 series offers various models, each designed for specific application needs while maintaining core Wi-Fi and BLE functionalities. The modules are characterized by their small form factor and integrated antenna.

3.1 Visual Overview

Video: A detailed 360-degree view of the ESPC3-05-N4 module, showcasing its compact design and pin layout.
Group image of ESPC3-20E-N4, ESPC3-05-N4, and ESPC3-12-N4 modules with dimensions.
Image: Overview of ESPC3-20E-N4 (18x20mm), ESPC3-05-N4 (16x20mm), and ESPC3-12-N4 (16x24mm) modules, highlighting their physical appearance and dimensions.

4. Specifications

The following table outlines the general specifications for the ESPC3 series modules:

AttributeValue
Brand NameJessinie
TypeVoltage Regulator (Module)
ApplicationComputer
ConditionNew
Operating TemperatureNormal
Dissipation PowerLow
Supply Voltage- (Refer to specific module datasheet for details)
is_customizedYes
PackageModule
High-concerned chemicalNone

5. Module Identification and Pinouts

Each module in the ESPC3 series has a unique pin configuration. Refer to the diagrams below for specific pin assignments for each model.

5.1 ESPC3-05-N4

Pinout diagram for ESPC3-05-N4 module.
Image: Pinout diagram for the ESPC3-05-N4 module, showing VCC, GND, various GPIOs (IO0-IO9, IO18, IO19), TXD, RXD, and EN pins.

5.2 ESPC3-12-N4

Pinout diagram for ESPC3-12-N4 module.
Image: Pinout diagram for the ESPC3-12-N4 module, detailing pins such as VCC, GND, IO0-IO8, TXD, RXD, EN, and several NC (No Connect) pins.

5.3 ESPC3-12E-N4

Pinout diagram for ESPC3-12E-N4 module.
Image: Pinout diagram for the ESPC3-12E-N4 module, indicating VCC, GND, IO0-IO8, TXD, RXD, EN, and NC (No Connect) pins.

5.4 ESPC3-20-N4 and ESPC3-20E-N4

These modules feature a similar pin configuration to other ESPC3 variants, typically including VCC, GND, various GPIO pins, TXD, RXD, and EN. For detailed pin assignments, refer to the markings on the module itself or the specific datasheet for ESPC3-20-N4 and ESPC3-20E-N4.

Close-up of ESPC3-20-N4 module.
Image: Close-up view of the ESPC3-20-N4 module, showing its integrated antenna and model identification.
Close-up of ESPC3-20E-N4 module.
Image: Close-up view of the ESPC3-20E-N4 module, displaying its integrated antenna and model identification.

6. Setup Instructions

  1. Power Supply: Connect the VCC pin to a stable 3.3V power source and GND to ground. Ensure the power supply can provide sufficient current for both Wi-Fi and BLE operations.
  2. Data Connection: Connect the TXD and RXD pins to your host microcontroller's UART (Universal Asynchronous Receiver/Transmitter) pins. Cross-connect: module TXD to host RXD, and module RXD to host TXD.
  3. Enable Pin (EN): The EN pin typically needs to be pulled high (3.3V) for the module to operate. A pull-up resistor is often recommended.
  4. Programming Pins: For flashing new firmware, specific GPIO pins (e.g., IO0) might need to be held low during power-up to enter bootloader mode. Consult the specific module's datasheet or development board documentation for exact programming procedures.
  5. Antenna: The modules feature an onboard antenna. Ensure there are no metallic objects or ground planes directly beneath or too close to the antenna area to optimize Wi-Fi/BLE performance.

7. Operating Instructions

  1. Firmware Upload: Use a compatible USB-to-UART converter and the appropriate flashing tool (e.g., ESP-IDF, Arduino IDE with ESP32-C3 core) to upload your application firmware to the module.
  2. Development Environment: The ESPC3 series is compatible with Espressif's ESP-IDF framework and can also be programmed using the Arduino IDE or MicroPython.
  3. Wi-Fi Connectivity: Implement Wi-Fi station or access point functionality in your code to connect to networks or create your own.
  4. BLE Communication: Utilize the Bluetooth Low Energy (BLE) capabilities for short-range wireless communication with other BLE-enabled devices.
  5. GPIO Control: Program the General Purpose Input/Output (GPIO) pins to interact with external sensors, actuators, and other peripherals.

8. Maintenance

  • Keep the module clean and free from dust and debris.
  • Avoid physical stress or bending of the module.
  • Regularly check for firmware updates from the module manufacturer or community to ensure optimal performance and security.
  • Store unused modules in anti-static bags in a dry environment.

9. Troubleshooting

  • Module not powering on: Check power supply connections (VCC, GND) and ensure the EN pin is pulled high. Verify the power supply provides stable 3.3V.
  • Failed firmware upload: Ensure correct programming pins are used, the module is in bootloader mode, and the USB-to-UART converter drivers are installed correctly. Check baud rate settings.
  • Wi-Fi/BLE connectivity issues: Verify antenna clearance. Check firmware logic for correct Wi-Fi/BLE initialization and credentials. Ensure sufficient power supply for radio operations.
  • UART communication errors: Double-check TXD/RXD connections (cross-connected), baud rate, and parity settings.

10. User Tips

  • For development, consider using a breakout board that simplifies pin access and power regulation.
  • Always refer to the official Espressif documentation for the ESP32-C3 series for in-depth technical details and programming guides.
  • When integrating into a custom PCB, pay close attention to power supply decoupling and antenna layout for optimal performance.

11. Warranty and Support

For warranty information and technical support, please contact your point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.