Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of the Midea Range Hood Display Board Key Control Circuit, model YAL18-CC20. This component is designed as a replacement or repair part for compatible Midea range hood models DT318, 320R, and DJ520. Please read this manual thoroughly before proceeding with any procedures.

Figure 1: Midea Range Hood Display Board Key Control Circuit YAL18-CC20
Setup and Installation
Warning: Installation involves electrical components. To avoid electric shock or damage to the appliance, always disconnect power to the range hood at the circuit breaker before beginning installation. It is highly recommended that installation be performed by a qualified technician.
Required Tools:
- Screwdriver set (Phillips and/or flathead, depending on range hood fasteners)
- Needle-nose pliers (optional, for connectors)
- Multimeter (for verifying power disconnection, recommended)
Installation Steps:
- Disconnect Power: Locate the circuit breaker for your kitchen or the specific range hood and turn off the power. Verify power is off using a multimeter.
- Access the Control Panel: Carefully remove the outer casing or access panel of your Midea range hood to expose the existing display board. Refer to your specific range hood model's service manual for exact access procedures.
- Disconnect Old Board: Gently disconnect all wiring harnesses and ribbon cables connected to the old display board. Note the orientation and connection points for reassembly.
- Remove Old Board: Unscrew or unclip the old display board from its mounting points.
- Install New Board: Position the new YAL18-CC20 display board in the same location as the old one. Secure it with the original screws or clips.
- Connect Wiring: Reconnect all wiring harnesses and ribbon cables to the new board. Ensure all connections are firm and correctly oriented. The connector shown in Figure 1 should match the corresponding port on your range hood's main circuit.
- Reassemble: Carefully reattach the range hood's casing or access panel.
- Restore Power: Turn the power back on at the circuit breaker.
- Test Functionality: Verify that the display illuminates and all buttons (fan speed, light, timer, etc.) respond correctly.
Operating Instructions
The YAL18-CC20 Display Board Key Control Circuit restores the original control functionality of your Midea range hood. Operating instructions for the range hood itself remain unchanged. Please refer to your Midea range hood's user manual for detailed operating procedures, including:
- Turning the fan on/off and adjusting fan speeds.
- Operating the range hood lighting.
- Setting and canceling timer functions.
- Any other specific features of your range hood model.
The display will show relevant information such as fan speed, timer settings, or other indicators as designed by your range hood model.
Maintenance
The YAL18-CC20 display board itself requires minimal maintenance. To ensure its longevity and proper function:
- Cleaning: If the display or buttons become dusty, gently wipe them with a soft, dry, lint-free cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as these can damage the electronic components or the display surface. Always ensure the range hood is powered off before cleaning.
- Avoid Liquid Exposure: Prevent liquids from spilling onto or entering the control panel area.
- Environmental Conditions: Ensure the range hood operates within its specified environmental conditions (temperature, humidity) to prevent damage to electronic components.
Troubleshooting
If you experience issues after installing the YAL18-CC20 display board, consider the following troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Display does not light up / No power | Power not restored; Loose connection; Faulty board | Check circuit breaker. Re-verify all cable connections. If problem persists, consult a qualified technician. |
| Buttons are unresponsive | Loose connection; Incorrect installation; Faulty button/board | Ensure all ribbon cables are securely connected. Re-check installation steps. If problem persists, consult a qualified technician. |
| Incorrect display readings | Software/firmware issue (unlikely for a replacement board); Faulty board | Power cycle the range hood (turn off at breaker for 1 minute, then on). If issue persists, contact seller or technician. |
If these steps do not resolve the issue, it is recommended to contact a qualified appliance repair technician or the seller for further assistance.
Specifications
| Feature | Detail |
|---|---|
| Product Type | Display Board Key Control Circuit for Range Hood |
| Model Number | YAL18-CC20 |
| Compatible Range Hood Models | Midea DT318, 320R, DJ520 |
| Material | Plastic |
| Origin | Mainland China |
| High-concerned chemical | None |
Warranty and Support
For warranty information, please refer to the terms provided by your original seller or the manufacturer. Keep your purchase receipt as proof of purchase.
If you require technical support or have questions regarding the product, please contact the seller directly through your purchase platform. Provide them with your order number and a detailed description of the issue.
User Tips
- Verify Compatibility: Always double-check the model numbers of your range hood against the compatible models listed for this control board (DT318, 320R, DJ520) to ensure proper fit and function.
- Handle with Care: Electronic components are sensitive. Avoid touching the circuit board directly with bare hands to prevent static discharge.
- Professional Installation: If you are not comfortable working with electrical components, it is always best to hire a certified technician for installation to ensure safety and correct functionality.