1. Introduction
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your JINGSHA X99 MAX DDR4 Motherboard LGA 2011-3 Set Kit, which includes a Xeon E5 2695 V4 CPU. Please read this manual thoroughly before proceeding with any installation or operation to ensure proper functionality and safety.
2. Warning & Safety Information
- Do not use in humid environments.
- Avoid areas with strong electromagnetic interference.
- Disconnect power before installation. Always ensure the power supply is unplugged from the wall outlet before handling any components.
- When inserting or removing hardware, take care not to damage motherboard pins. Handle components gently and align them correctly.
- Prevent electrostatic discharge (ESD) damage during installation. Use an anti-static wrist strap or touch a grounded metal object before handling components.
- Do not force hardware insertion or removal. If a component does not fit easily, recheck its orientation and compatibility.
- Ensure adequate ventilation and heat dissipation. Proper airflow is crucial for system stability and longevity.
3. Setup and Installation
Follow these steps to install the CPU, memory, and M.2 SSD, and prepare your system for initial power-on.
3.1 CPU Installation
- Step 1: Prepare the Socket. Open the pressure bar marked on the CPU socket. Then, open the buckle cover of the CPU base.
- Step 2: Insert the CPU. When placing the CPU into the slot, pay attention to the four defenses (silent notch) and align the gold mountain corner on the CPU with the golden corner of the motherboard. Be careful not to bend pins.
- Step 3: Secure the CPU. Re-buckle the previously opened lever to secure the CPU in place.
3.2 Memory (RAM) Installation
- Insert the DDR4 memory modules into the appropriate DIMM slots. Ensure the modules are correctly oriented and press down firmly until the retention clips on both sides snap into place.
3.3 M.2 SSD Installation
- Install the M.2 SSD correctly as shown in the figure to prevent the interface from falling off due to stress. Gently insert the M.2 SSD into the M.2 slot and secure it with the provided screw.
3.4 Power Connections
- Connect the 24-pin ATX power connector and the 8-pin 12V CPU power connector from your power supply to the motherboard.
- Ensure your power supply is at least 500W to adequately support the system.
3.5 Initial Power On
- After all components are securely installed and power cables connected, power on the computer.
- Observe the boot process. If the system does not power on, refer to the Troubleshooting section.
4. Operating Instructions
Once the system is assembled and powered on, the motherboard will initiate the boot sequence. Ensure a monitor is connected to view the BIOS/UEFI interface or operating system loading process.
4.1 BIOS/UEFI Access
- To enter the BIOS/UEFI setup, press the designated key (commonly DEL, F2, F10, or F12) repeatedly during the initial boot screen. Consult your monitor for the exact key prompt.
- The BIOS is AMI EFI BIOS.
4.2 Operating System Installation
- Prepare a bootable USB drive or DVD with your preferred operating system.
- Access the BIOS/UEFI to set the boot order, prioritizing your installation media.
- Follow the on-screen instructions to install the operating system.
5. Specifications
5.1 Motherboard Specifications (X99E MAX)
| Feature | Description |
|---|---|
| Brand | JINGSHA |
| Form Factor | M-ATX, 244mm x 221mm |
| CPU Socket | LGA 2011-3 (supports LGA 2011-V3 Full Series CPU, Xeon E5 26xx V3 V4 series) |
| Memory Type | 8* UDIMM DDR4 |
| Memory Frequency | Supports 1600/1866/2133/2400MHz |
| Max Memory | Quad channel up to 256GB |
| PCIe Slots | 1* PCI-E 16X, 1* PCI-E 4X (PCI-E 3.0 standards) |
| Storage | 7* SATA3.0 ports, 1* M.2 NVMe 3.0 x4 port, 1* M.2 NGFF SATA3.0 port |
| USB Ports | 4* USB3.0 (front 2*USB3.0), 6* USB2.0 (front 4*USB2.0) |
| LAN | Gigabit Ethernet LAN port (1*RTL8111H, 1000Mbps Ethernet) |
| Audio | Realtek Audio Codec ALC897, 5.1 Channel HD Audio Chip |
| PSU Solution | 1* 8 Pin + 1* 24 Pin Power Supply |
| Integrated Video Card | No |
| Back I/O Ports | 2*USB 5Gbps Ports, 6*USB2.0 Ports, 1*RJ45 LAN Port, 1*Audio 3-in-1(Line-out/Line-in/MIC) |
| Other Onboard Connectors | 1*4pin CPU Smart FAN header, 1*SYS FAN header, 1*Front Audio header, 1*USB5Gbps header (for two USB5Gbps ports), 1*USB2.0 header (for two USB2.0 ports), 1*RS232 COM header, 1*Front control panel header, 1*Speaker header, 1*CMOS header, 1*power on header, 1*24pin ATX connector, 1*8pin 12V connector |
5.2 CPU Specifications (Xeon E5 2695 V4)
- Processor Series: Xeon E5 2695 V4
- Cores/Threads: 18 cores / 36 threads
- Main Frequency: 2.1GHz
- Socket Type: LGA2011-3
- 3rd Level Cache: 45MB
- Technology: 14nm
- Power Consumption: 120W
6. Feature Overview
- Processor Compatibility: Supports LGA2011-v3 Intel Xeon E5 series CPUs.
- Memory Support: Motherboard supports DDR4 ECC Registered memory, with 8 DIMM slots for quad-channel memory up to 256GB.
- High-Speed Storage: Features full-speed M.2 NVMe and M.2 NGFF interfaces for fast data dissemination, stable and reliable performance.
- Robust Power Delivery: Equipped with all solid-state capacitors and an 8-phase power supply for stable operation.
- Enhanced Stability: Multilayer PCB design for increased stability and durability, complemented by an aluminum heatsink for highly enhanced stability and heat resistance.
- Gigabit Ethernet: Integrated 1000Mbps Ethernet for fast and reliable network connectivity.
- PCIe 3.0 x16 Slot: Provides higher bandwidth and lower latency for graphics cards and other expansion cards.
7. Maintenance
- Keep the system clean: Regularly clean dust from the motherboard, CPU cooler, and case fans to ensure optimal cooling and prevent overheating.
- Ensure proper ventilation: Make sure your PC case has adequate airflow and is not placed in an enclosed space that restricts ventilation.
- BIOS Updates: Periodically check the manufacturer's website for BIOS updates to improve system stability, compatibility, and performance.
- Handle with care: When performing any internal maintenance, always disconnect power and take anti-static precautions to prevent damage.
8. Troubleshooting (FAQ)
- Q: System fails to power on.
- A: Verify that all power connections (24-pin ATX, 8-pin CPU) are securely seated. Ensure the CPU and memory are properly installed in their respective sockets/slots.
- Q: Blue Screen of Death (BSOD) occurs.
- A: This can indicate hardware or software issues. Try updating the motherboard BIOS to the latest version. Also, verify hardware compatibility for all installed components, especially RAM and expansion cards.
- Q: Hard drive not recognized.
- A: Confirm that the SATA data and power cables are correctly connected to both the hard drive and the motherboard. Check BIOS settings to ensure SATA ports are enabled and the drive is detected.
9. Warranty and Support
The CPU included in this kit comes with a 1-year warranty from the date of purchase. Please retain your proof of purchase for warranty claims.
For further technical assistance, BIOS files, or drivers, please contact customer service. You can also refer to the official user manual PDF for more detailed information: View User Manual (PDF)