1. Product Overview
The DASQUA IP65 Water Proof Electronic Outside Micrometer is a precision measuring instrument designed for accurate external measurements. It features a large LCD screen for easy reading, IP65 protection against liquids, and durable carbide measuring surfaces. This manual provides instructions for the proper use and maintenance of your micrometer to ensure optimal performance and longevity.
2. Specifications
| Code | Range | Graduation | Accuracy |
|---|---|---|---|
| 4410-1105 | 0-25mm / 0-1" | 0.01mm | 0.003mm / 0.00015" |
| 4410-1110 | 25-50mm / 1"-2" | 0.01mm | 0.003mm / 0.00015" |
| 4410-1115 | 50-75mm / 2"-3" | 0.01mm | 0.004mm / 0.00015" |
| 4410-1120 | 75-100mm / 3"-4" | 0.01mm | 0.004mm / 0.00015" |
| 4410-1125 | 100-125mm / 4"-5" | 0.01mm | 0.005mm / 0.0002" |
| 4410-1130 | 125-150mm / 5"-6" | 0.01mm | 0.005mm / 0.0002" |
3. Key Features
- Large, easy-to-read LCD screen for clear measurement display.
- Manufactured in accordance with DIN863 standards for precision.
- Spindle is hardened, ground, and lapped to ensure ultimate accuracy.
- Equipped with a spindle lock for securing measurements.
- Features Absolute (ABS), Inch-Metric Conversion (in/mm), and Zero-Set functions.
- IP65 protection rating ensures resistance against liquid and dust ingress.
- Stainless steel construction on the spindle for enhanced durability.
- Carbide measuring surfaces are ground for extended service life and consistent accuracy.
- Ratchet stop mechanism for applying constant measuring force (5-8N), 20% higher than normal for improved consistency.
4. Setup
-
Unpacking and Initial Inspection: Carefully remove the micrometer from its packaging. Inspect for any visible damage. Ensure all components, including the protective case and any calibration standards (if applicable to your model), are present.
Figure 3: Micrometer in its retail packaging -
Cleaning: Before first use, gently wipe all measuring surfaces and the spindle with a clean, lint-free cloth. Avoid using harsh chemicals that could damage the finish or electronic components.
Figure 4: Close-up of the micrometer's measuring surfaces - Power On: Press the ON/OFF button to turn on the micrometer. The LCD display should illuminate.
-
Zero Setting:
- Clean both the anvil and spindle faces thoroughly.
- Gently close the measuring faces by rotating the thimble or ratchet stop until they meet. Use the ratchet stop to apply consistent force.
- Press the ZERO button. The display should read "0.000" (or "0.00" depending on resolution). If not, repeat the process.
5. Operating Instructions
- Selecting Measurement Units (in/mm): Press the in/mm button to switch between inch and millimeter units. The selected unit will be indicated on the LCD display.
-
Absolute (ABS) / Incremental (INC) Measurement: Press the ABS button to toggle between Absolute and Incremental measurement modes. In Absolute mode, measurements are taken from the set zero point. In Incremental mode, you can set a temporary zero at any point to measure differences.
Figure 5: Micrometer display showing Incremental (INC) mode -
Taking a Measurement:
- Open the measuring faces slightly wider than the object to be measured.
- Position the object between the anvil and the spindle.
- Rotate the thimble or ratchet stop until the measuring faces gently contact the object. Use the ratchet stop for consistent measuring force.
- Read the measurement directly from the LCD display.
- Using the Spindle Lock: To hold a measurement, rotate the spindle lock knob clockwise to secure the spindle in place. This prevents accidental changes to the reading.
-
Data Output (if applicable): Some models may feature a data output port for connecting to external devices for data collection. Refer to specific software or cable instructions for usage.
Figure 6: Data output port - Power Off: Press and hold the ON/OFF button to turn off the micrometer when not in use to conserve battery life.
6. Maintenance
- Cleaning: Regularly clean the micrometer, especially the measuring faces, with a clean, soft, lint-free cloth. For stubborn dirt, a small amount of isopropyl alcohol can be used, but avoid excessive moisture, especially near the electronics. Do not use abrasive cleaners.
- Storage: Store the micrometer in its protective case when not in use. Keep it in a dry, clean environment, away from direct sunlight, extreme temperatures, and corrosive substances. Ensure the measuring faces are slightly open to prevent pressure on the spindle.
- Battery Replacement: If the display becomes dim or erratic, the battery may need replacement. Typically, these micrometers use a CR2032 lithium coin cell battery. To replace, locate the battery compartment cover (usually on the back of the display unit), remove the screw(s), and carefully replace the battery, observing polarity. Dispose of old batteries responsibly.
- Calibration: While the micrometer is factory calibrated, periodic checks with a known standard (e.g., gauge blocks) are recommended to ensure continued accuracy. If significant deviation is observed, professional calibration may be required.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Display is blank or dim | Low or dead battery; Micrometer is off | Press ON/OFF button; Replace battery |
| Inaccurate readings | Measuring faces are dirty; Incorrect zero setting; Environmental factors (temperature) | Clean measuring faces; Re-zero the micrometer; Allow micrometer to acclimate to ambient temperature |
| Display shows error message | Electronic malfunction; Excessive force applied | Turn off and on again; Avoid applying excessive force; If problem persists, contact support |
| Buttons unresponsive | Low battery; Internal electronic issue | Replace battery; If problem persists, contact support |
8. User Tips
- Always use the ratchet stop when taking measurements to ensure consistent and repeatable force, which is crucial for accuracy.
- Keep the micrometer and the workpiece at the same temperature to avoid measurement errors due to thermal expansion or contraction.
- When storing, ensure the measuring faces are slightly separated to prevent wear and tear on the carbide surfaces and to avoid putting constant pressure on the spindle.
- Regularly check the zero point before critical measurements to maintain precision.
9. Warranty and Support
This DASQUA micrometer comes with a 2-year warranty from the date of purchase, covering defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.
For technical support, warranty service, or inquiries regarding replacement parts, please contact your authorized DASQUA dealer or the point of purchase. Provide the model number and a detailed description of the issue when seeking assistance.