Audi 8W0 035 736

Contents

User Manual: Audi CarPlay USB AUX Smartphone Interface Socket and Cable Harness

Model: 8W0 035 736

1. Introduction

This manual provides detailed instructions for the installation, operation, and troubleshooting of the Audi CarPlay USB AUX Smartphone Interface Socket and Cable Harness. This product is designed to integrate smartphone connectivity features like CarPlay, USB, and AUX into compatible Audi vehicles, including A4, A5, B9, 8W, Q5, Q7, and FY models. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.

Audi CarPlay USB AUX Smartphone Interface Socket Plug and Cable Harness Kit

Figure 1: Audi CarPlay USB AUX Smartphone Interface Socket Plug and Cable Harness Kit

2. Installation Guide

2.1. Pre-Installation Preparation

Before beginning the installation process, ensure all necessary components are available and take appropriate safety measures.

  • Required Components:
    • Head unit (if applicable)
    • Fascia frame
    • Power/CANBUS cable
    • GPS antenna
    • USB cable
    • Rear camera cable (if applicable)
    • Basic installation tools (e.g., plastic trim tool, screwdrivers)
  • Safety Precaution: Disconnect the vehicle's negative battery terminal to prevent short circuits or other electrical hazards.

2.2. Removing the Original Center Console

Carefully remove existing components to access the installation area.

  1. Use a plastic trim tool to gently detach the decorative panel surrounding the center console. Apply minimal force to avoid damaging clips.
  2. Unscrew any mounting screws securing the original unit.
  3. Disconnect the factory wiring harness and antenna connector from the original unit.
  4. Store all removed parts safely to prevent loss or damage.

2.3. Android Head Unit Installation Verification & Wiring Connection

Follow these steps for connecting the new interface and associated components.

Full kit including the CarPlay USB AUX socket module and various cable harnesses

Figure 2: CarPlay USB AUX socket module and cable harnesses

Wiring Connection:

  1. Connect the power harness to the vehicle's original factory connector.
  2. If your vehicle has a CANBUS system, ensure the decoder is correctly installed and configured (refer to Section 2.5 CANBUS Setup Guide).
  3. Verify that the ACC (ignition) and constant power (B+) connections are secure and properly matched.

Accessory Installation:

  1. Install the GPS antenna in an optimal location for signal reception.
  2. Connect the USB extension cable for additional connectivity.
  3. If applicable, connect the rear-view camera video input cable and reverse trigger wire according to the wiring diagram.

2.4. System Testing

After initial connections, perform a system test before final assembly.

  1. Reconnect the vehicle's negative battery terminal and switch the ignition to ACC/ON.
  2. Confirm that the head unit powers on properly.
  3. Test all major functions:
    • Steering wheel control integration
    • Reverse camera display
    • Radio reception
    • Bluetooth connectivity
  4. Ensure proper operation of all features for a fully functional system.

2.5. CANBUS Setup Guide

Proper CANBUS configuration is essential for full system integration.

1. Enter the Settings Menu

  • Power on the unit and navigate to Settings > Factory Settings.
  • You may be prompted for a password. Common default passwords include 8888, 1234, or 0000, depending on the device.

2. Select the Correct CANBUS Type

  • In the CAN Type or Protocol section, choose the vehicle brand and model that matches your car's protocol.

Important:

It is crucial to select the exact matching protocol. Choosing the wrong one may result in issues such as:

  • Steering wheel controls not functioning
  • No sound from parking sensors
  • Other system malfunctions

3. Save and Restart

  • Once the correct protocol is selected, save the settings.
  • Restart the head unit for the changes to take effect.

4. Function Test

After rebooting, verify the following features:

  • Steering wheel controls
  • Reverse camera and parking sensor sound
  • Automatic headlight reminders
  • Door status display
  • Air conditioning information display (if supported)

2.6. Final Installation & Securing

Complete the installation by securing the unit and reassembling the console.

  1. Position the head unit into the fascia frame and secure it using the designated mounting screws. Ensure proper alignment and stability.
  2. Align the retaining clips with their corresponding slots and carefully press the trim panel back into place. Ensure the panel fits flush against the dashboard for a factory-style appearance.
  3. Organize the wiring harness using cable ties to bundle and secure any excess cables. Ensure that the wiring is neatly routed and kept away from moving parts and ventilation ducts to prevent interference and potential noise.

3. Operation

This interface provides seamless integration for CarPlay, USB, and AUX functionalities in your Audi vehicle.

3.1. CarPlay Connectivity

  • Connect your iPhone to the designated USB port using a certified Lightning cable.
  • CarPlay should automatically launch on your vehicle's display.
  • Navigate CarPlay using your vehicle's controls (e.g., MMI controller, steering wheel buttons, touchscreen if available).

3.2. USB Media Playback

  • Insert a USB drive containing media files (e.g., MP3, MP4) into the USB port.
  • Access the USB media player through your vehicle's infotainment system.
  • Use the vehicle controls to browse and play your media.

3.3. AUX Input

  • Connect an external audio device (e.g., MP3 player, smartphone) to the AUX input using a 3.5mm audio cable.
  • Select the AUX input source on your vehicle's infotainment system.
  • Control playback from your external device.

4. Care and Maintenance

  • Cleaning: Use a soft, dry cloth to clean the interface socket and surrounding areas. Avoid abrasive cleaners or solvents.
  • Cable Management: Ensure all cables are securely routed and not pinched or exposed to excessive heat or moisture.
  • Software Updates: Periodically check for any available software or firmware updates for your head unit or CarPlay system to ensure optimal performance and compatibility.

5. Troubleshooting

This section addresses common issues and their potential solutions.

Common Troubleshooting Scenarios:

ProblemPossible CauseSolution
No parking sensor soundIncorrect vehicle protocol selected in CANBUS settings. Factory amplifier option not enabled.Ensure the correct vehicle protocol is selected in Settings > Factory Settings > CAN Type/Protocol. Check if the factory amplifier option is enabled in the settings.
Steering wheel controls not workingIncorrect CANBUS protocol selection.Double-check the protocol selection in CANBUS settings. If the exact one is unavailable, try selecting a similar vehicle protocol.
Vehicle information not displayed (e.g., AC info, door status)Your vehicle may not support full CAN data integration for these specific features.Verify compatibility with your specific Audi model and year. Some older models may have limited CAN data output.
CarPlay/USB/AUX not recognizedLoose connection, faulty cable, incorrect source selection.Check all cable connections. Try a different USB cable or device. Ensure the correct input source is selected on your infotainment system.
Unit does not power onPower harness not connected correctly, blown fuse, battery disconnected.Verify power harness connections. Check vehicle fuses. Ensure the negative battery terminal is securely reconnected.

6. Specifications

Key technical specifications for the Audi CarPlay USB AUX Smartphone Interface Socket.

FeatureDetail
Model NameFor Audi
Part Number8W0 035 736
Special FeaturesFor Audi CarPlay Socket
Item TypeCables, Adapters & Sockets
InterfaceUSB 2.0
MaterialABS
Item Weight0.3kg
OriginMainland China
PCB IncludedNo
High-concerned chemicalNone

7. User Tips

  • Professional Installation Recommended: Due to the complexity of car electronics and trim removal, professional installation is highly recommended to avoid damage to your vehicle or the product.
  • Double-Check Compatibility: Always confirm the part number and vehicle compatibility (model and year) before purchasing and installing to ensure proper fit and function.
  • Firmware Updates: Keep an eye out for any firmware updates from the manufacturer, as these can improve performance, add features, or resolve compatibility issues.
  • Cable Quality: Use high-quality USB and AUX cables for optimal audio and data transfer, especially for CarPlay, to prevent connectivity issues.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the product manufacturer directly. Keep your purchase receipt as proof of purchase for any warranty claims.

9. Product Video Demonstration

Watch this video for a visual overview of various car wiring harnesses and CAN bus decoders, including components similar to the CarPlay USB AUX interface.

Video: Overview of car wiring harnesses and CAN bus decoders.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.