User Manual: ASUS ET2011AGK ET2011AG All-in-one Motherboard

Introduction

This manual provides comprehensive instructions for the installation, operation, and troubleshooting of your ASUS ET2011AGK ET2011AG All-in-one Motherboard. Please read this manual carefully before proceeding with installation or use. If you encounter any problems, please contact technical support.

Figure 1: Top view of the H61C Motherboard (LA-5951P)

Figure 2: Bottom view of the H61C Motherboard (LA-5951P)

1. Setup

1.1 Package Contents

• JUXIESHI H61C Motherboard (LA-5951P) x 1
• SATA Cable x 1
• I/O Shield x 1

1.2 Motherboard Layout and Connectors

The H61C motherboard features various ports and connectors for system components. Key areas include:

• Top Side: CPU Socket, DDR3 DIMM slots, 4-pin CPU Fan connector, 24-pin DC power connector, NVME/NGFF M.2 slot, USB 2.0 ports, HDMI, VGA, 100MB LAN, Audio ports.
• Bottom Side: PCIe X16 slot, PCIe X1 slot, SATA 2.0 ports, 3-pin System Fan connector, JBAT1 (Clear CMOS button).

For a detailed visual representation of the motherboard layout and specific port locations, please refer to the original PDF user manual.

1.3 Install CPU & Fan

Important Safety Note:

• Always unplug the power cord from the power outlet before installing or removing the CPU.
• Ensure the motherboard supports your specific CPU model (LGA 1155).
• Do not turn on the computer without a CPU cooler installed to prevent damage.
• Apply an even layer of thermal paste between the CPU and heatsink.
• Protect CPU socket pins with the protective cap when the CPU is not installed.

1. Open the CPU socket lever.
2. Carefully place the CPU into the socket, ensuring correct orientation (match the triangle/notch).
3. Close the lever to secure the CPU.
4. Install the CPU cooler onto the CPU, ensuring it is firmly seated and makes good contact.
5. Connect the 4-pin CPU fan power connector to the CPU_FAN header on the motherboard.
6. Ensure the 4-PIN power supply is connected to power the CPU.

1.4 Install Memory

Important Safety Note:

• Turn off the computer and unplug the power cord before installing memory.
• Use memory modules of the same capacity, brand, speed, and chips for optimal performance.
• Memory modules have a foolproof design; if it doesn't fit, try rotating it 180 degrees.

The motherboard provides two DDR3 DIMM slots, each supporting up to 16GB (total 32GB). For Dual-Channel mode, two memory modules are required.

1. Wrench the latches on both sides of the memory slot outwards.
2. Insert the memory module into the slot, aligning it with the notch.
3. Flip the latches on both sides of the slot inwards to lock the memory module in place.

1.5 Install Expansion Card

Important Safety Note:

• Always turn off the power supply and unplug the power cable before adding or removing expansion cards.
• Incorrect installation can cause short circuits and damage components.

The motherboard includes a PCI Express 2.0 x16 slot and a PCI Express 2.0 x1 slot.

1. Align the expansion card with the desired PCIe slot.
2. Press the expansion card firmly until it is fully inserted into the slot.

1.6 Back Panel I/O Ports

The back panel provides the following input/output ports:

• USB 2.0 Ports: 6 ports for connecting various USB devices.
• VGA Port: For connecting VGA-compatible displays.
• HDMI Port: Supports high-definition video and audio output up to 1080p and 4K.
• RJ45 LAN Port: Provides Internet connection up to 100Mbps.
• Audio Jacks: Line-in, Line-out, and Mic-in for audio input/output.

1.7 Internal Connectors

Important Safety Note:

• Incorrect connections can damage the device or prevent it from working.

The motherboard features several internal connectors for front panel devices and other components:

• F_PANEL1 Connector: For connecting front panel power LED, power switch, HDD LED, and reset switch.
• SPEAK1 Connector: For connecting the system speaker (buzzer).
• F_AUDIO1 Connector: For connecting front panel audio jacks (MIC L, MIC R, Head Phone R, Head Phone L, Ground, MIC Detection, SENSE_SEND, No Pin).
• F_USB1 Connector: Front USB 2.0 connector.
• FP_USB3_1 Connector: Front USB 2.0 connector.

For detailed pinout configurations of these connectors, please refer to the tables in the original PDF user manual.

1.8 Storage Ports

• SATA1-SATA3: Three SATA 2.0 connectors (3Gb/s) for connecting SATA devices.
• M.2 Slot: Supports NGFF/NVME Protocol M.2 SSDs. To install, insert the M.2 SSD at a 30-degree angle and secure it with a screw. Refer to the original PDF user manual for details on switching SATA M.2 or NVME M.2 Mode.

1.9 Power Connectors

Ensure all power connectors are securely plugged in before powering on the system.

• ATXPWR1 (24-pin Power Connector): Provides power to the motherboard.
• ATX12V1 (4-pin CPU Power Connector): Provides dedicated power to the CPU.

Important Safety Note:

• A power supply of at least 500W is recommended for stable operation.

ATXPWR1 Pinout:

ATX12V1 Pinout:

1.10 Fan Connectors

• CPU_FAN1 (4-pin): For CPU cooler. Note: This 4-pin fan does not have PWM speed regulation.
• SYS_FAN1 (3-pin): For system chassis fan. Note: This 3-pin fan does not have PWM setting.

CPU_FAN Pinout:

SYS_FAN Pinout:

1.11 USB Connectors

F_USB1 (Front USB 2.0 Connector):

FP_USB3_1 (Front USB 2.0 Connector):

2. Operating

2.1 BIOS Setting

The BIOS (Basic Input and Output System) stores hardware parameters in the CMOS on the motherboard. It performs the Power-On Self-Test (POST) and loads the operating system. The BIOS Setup program allows you to modify basic system configurations.

Important Note on BIOS Flashing:

• BIOS flashing is potentially risky. Only flash the BIOS if you encounter problems that require it.
• Inadequate BIOS flashing can lead to system malfunction. Unauthorized BIOS flashing may void your warranty.

2.2 Enter BIOS Setup

To enter the BIOS Setup Menu:

1. Turn on your computer.
2. During the self-test process, press the 'DEL' key when prompted.
3. Alternatively, you can use the 'F11' key as a Quick Boot Key.

If the prompt disappears too quickly, you can restart your computer by pressing the Reset button on the case or by pressing Ctrl+Alt+Delete simultaneously.

2.3 Reset BIOS

To restore default BIOS settings or resolve certain issues, you can reset the BIOS by clearing the CMOS:

Important Safety Note:

• Ensure the computer is completely off before clearing CMOS data.

Locate the JCMOS1 jumper on the motherboard. To clear CMOS:

1. The initial state covers pins 1 and 2.
2. Pull out the jumper cap and place it to cover pins 2 and 3. Wait for approximately 3 minutes for the discharge to complete.
3. Restore the jumper cap to its initial state (covering pins 1 and 2).

3. Maintenance

Regular maintenance helps ensure the longevity and stable operation of your motherboard.

• Keep Clean: Periodically clean dust from the motherboard and components using compressed air. Ensure proper airflow within the PC case.
• Proper Handling: Always handle the motherboard by its edges to avoid touching sensitive components or pins. Use anti-static precautions when handling.
• CMOS Battery: The CMOS battery powers the BIOS settings when the system is off. If settings are lost frequently, the battery may need replacement.
• BIOS Updates: Only update the BIOS if necessary and follow official instructions carefully. Incorrect updates can cause irreversible damage.

4. Troubleshooting

If you encounter issues with your system, refer to the following troubleshooting steps:

4.1 Can't Boot (No response, no fan rotation, no indicator light)

1. Clear the CMOS jumper (refer to Section 2.3).
2. Check if the CPU is compatible with the motherboard.
3. Verify that the motherboard's power and CPU power supply cables are properly plugged in.
4. Ensure the system panel power-on cable is correctly connected.
5. Check if the power supply unit is functioning correctly.
6. Remove non-essential devices (graphics card, hard disk, USB devices) and attempt to boot.
7. If possible, try replacing the CPU with a known working one.

4.2 Start-up and then Shutdown (Fan rotates briefly, then system shuts down)

1. Clear the CMOS jumper.
2. Verify CPU compatibility.
3. Check if the CPU is damaged; replace if necessary.
4. Replace memory modules.
5. Remove non-essential devices (graphics card, hard drive, USB devices) and test again.

4.3 Computer Keeps Restarting (Reboot loop)

1. Clear the CMOS jumper.
2. Check if the CPU is compatible with the motherboard.
3. Check if the CPU is defective; replace if necessary.
4. Replace the RAM and check for compatibility or defects.
5. Remove non-essential devices (graphics card, hard disk, USB devices) and test again.

4.4 No Display

State 1: Fan rotating, Caps Lock key unresponsive.

1. Clear CMOS.
2. Check motherboard and CPU power supply connections.
3. Verify memory stick installation (ensure it's in the correct slot if specific slots are required).
4. Check CPU and memory compatibility with the motherboard.
5. Replace CPU.
6. Replace memory.

State 2: Fan rotating, Caps Lock key responsive.

1. Check if the monitor is turned on.
2. Check if the monitor display cable (DP, HDMI, DVI, VGA) is securely plugged in.
3. If using a CPU without integrated graphics (e.g., Intel Xeon series or 'F' suffix CPUs), ensure a dedicated graphics card is installed.
4. Verify the display data cable is connected to the correct port: to the motherboard's display interface if no discrete graphics card, or to the discrete graphics card's interface if one is installed.
5. Replace the data cable connected to the monitor.
6. Replace the graphics card.

4.5 Blue Screen or Crash

1. Check motherboard heat dissipation (CPU cooling fan working, cooler tightly fitted, thermal paste applied).
2. Replace the CPU.
3. Replace the memory.
4. Replace the hard disk.
5. Replace the operating system.
6. Replace the power supply.

5. Specifications

6. Warranty and Support

This product comes with a 30-day warranty period from the date of purchase. During this period, the product is guaranteed to be 100% functional and in good condition.

For any technical issues, questions, or concerns regarding your motherboard, please contact technical support promptly. We recommend referring to the comprehensive User Manual (PDF) for detailed diagrams and additional information.

Important:

• Warranty service may be voided if the motherboard is damaged due to improper installation by non-professionals.

7. User Tips

• Professional Installation Recommended: Electronic products require professional technical knowledge. If you are not an experienced computer repair technician, it is highly recommended to seek professional assistance for motherboard installation to prevent potential damage.
• Verify Compatibility: Before purchasing or installing, always confirm that the motherboard model (ET2011AGK ET2011AG NCL30 LA-5951P) is compatible with your existing system components, especially the CPU and memory.
• Inspect Upon Arrival: Carefully check the package for any damage immediately upon receipt. If the package is damaged, document it with photos.
• Confirm Motherboard Model: If you are unsure whether this motherboard is the exact match for your computer, send a picture of your current motherboard to customer service for confirmation before installation.