1. Introduction
Thank you for choosing the PC2332 Automatic Pool Cleaner. This user manual provides essential information to keep your cleaner in top working condition. Please read it carefully before use.
The PC2332 is a new generation of rechargeable, wireless pool cleaners designed to efficiently clean pools without the need for water changes. Powered by a built-in battery, it eliminates the hassle of long extension cords, offering greater ease of use. The cleaner features smart self-parking technology, automatically moving to the edge of the pool upon completion of its cleaning cycle for easy retrieval.
2. Important Reminders & Safety Information
- Please read this user manual carefully before use and operate the cleaner according to the instructions.
- Do not disassemble the internal parts of the cleaner without prior authorization. Unauthorized maintenance will void the warranty.
- Use only accessories recommended or sold by the manufacturer.
- Do not turn on the pool filtration system when the cleaner is operating in the pool.
- This cleaner is suitable for swimming pools with flat bottoms only.
- Do not allow minors to handle the cleaner.
- Do not use the cleaner when there are people in the pool.
- Turn off the cleaner before cleaning the filter or performing routine maintenance.
- It is recommended to clean the filter and filter compartment after each use.
- When charging, place the cleaner in a cool, ventilated area and do not cover it with any objects.
- Store the cleaner in a cool, ventilated place, away from direct sunlight. Before storing, soak it in clean water for one hour, allow it to cool, and then store to prevent corrosive media from damaging the cleaner.
- For prolonged periods of disuse, charge the cleaner every three months to maintain battery efficiency.
- This cleaner is suitable for swimming pools up to 860 ft².
- Do not use fingernails or other sharp objects to damage the cleaner's casing.
- Before charging, ensure that the charging socket, charging interface, and charging connector are completely dry.
- This cleaner is primarily designed to remove debris, particles, coarse sand, and other dirt from the pool, with optimal cleaning effect on granular dirt.
- During transport, protect the cleaner from violent vibration, impact, sun exposure, and rain.
- When stored outdoors, ensure measures are taken for rain, moisture, damage, and fire prevention.
- Products should be stored in temperatures between -20°C and 40°C, in a well-ventilated, non-corrosive environment with relative humidity not greater than 90%.
3. Product Structure
Familiarize yourself with the main components of your PC2332 pool cleaner:
- Outer Shell
- Recovery Hook
- Filter
- Charging Port
- On-Off Switch
- Bottom Compartment
4. Setup
4.1. Charging the Cleaner
- Use the accompanying charger to charge the cleaner.
- Ensure the On-Off switch is in the "OFF" position before charging.
- Verify that the charging port is completely dry before connecting the charger.
- During charging, the charger indicator light will be red. It will turn green when fully charged.
5. Operating Instructions
5.1. Before Operation
- Ensure that the top cover of the cleaner is properly aligned with the chassis before closing the buckle.
- Push the On-Off switch to "ON".
- A gentle beeping sound indicates the cleaner is ready to begin cleaning.
- A rapid beeping sound indicates the battery is low. Turn the cleaner off and recharge.
- A continuous beeping sound indicates a machine error. Turn off the cleaner and contact after-sales service.
5.2. Placing the Cleaner in the Pool
- At the shallow end of the pool, hold the cleaner just below the surface of the water to allow any trapped air to escape from the chassis.
- Face the cleaner in its intended cleaning direction.
- After all air has escaped, gently release the cleaner, or use the recovery hook to guide it to the bottom of the pool. Ensure the cleaner remains in an upright position.
- At this point, the cleaner will stop beeping. It will begin moving after approximately 15 seconds.
- The cleaner will automatically reverse when it touches the pool wall, utilizing its smart self-route planning.
5.3. Retrieving the Cleaner
- If the cleaner stops moving in the pool, use the recovery hook to lift it out of the water.
- Upon retrieval:
- A gentle beeping sound indicates the filter compartment needs cleaning (refer to Section 6.1).
- If cleaning is not yet finished, the cleaner can be returned to the pool to continue.
- If cleaning is finished, shut down the cleaner and charge it after ensuring the charging interface is dry.
- A rapid beeping sound indicates a low battery (refer to Section 4.1).
- A continuous beeping sound indicates a machine error. Turn off the cleaner and contact after-sales service.
- After using the cleaner, always shut it down and clean the filter tray screen and bottom compartment.
6. Maintenance
6.1. Filter Tray Cleaning
Regular cleaning of the filter tray is crucial for optimal performance.
- Open the clasp and lift the cleaner shell.
- Grasp the front and rear grooves of the filter tray and lift the filter tray upward.
- Clean the filter tray and bottom compartment thoroughly, for example, by rinsing with a hose.
- Reassemble the cleaner by placing the filter tray back into position and aligning the shell.
- Fasten the clasp securely.
7. Troubleshooting
Refer to the table below for common issues and their solutions.
| Symptom | Possible Cause | Solution |
|---|---|---|
| Charger indicator not working | Charger damage | Contact after-sales service. |
| No beep after turning on | Machine fault Boot failure Low battery |
Contact after-sales service. Turn off and restart the cleaner. Charge the cleaner (refer to Section 4.1). |
| Cleaner motionless on pool bottom for long period | Machine fault Boot failure Low battery Wheel jammed with debris Cleaner working incorrectly |
Contact after-sales service. Remove from pool and restart. Charge the cleaner (refer to Section 4.1). Remove debris from the wheel. Remove from pool, if continuous beeping or unresponsive, contact after-sales service. |
| Cleaner motionless after operating for a period | Cleaning task completed Low battery Wheel jammed with debris Filter tray clogged Cleaner working incorrectly Machine fault |
Remove cleaner, turn off, turn on, and return to pool. Charge cleaner (refer to Section 4.1) and clean filter. Remove debris from the wheel. Clean filter screen and chassis. Remove from pool, if continuous beeping or unresponsive, contact after-sales service. Remove from pool, if unresponsive, contact after-sales service. |
| Areas of the pool not cleaned | Special pool shape Too large a pool area Water circulation system is turned on |
Move cleaner to uncleaned area and resume operation. Move cleaner to uncleaned area and resume operation. Turn off the water circulation system. |
8. Buzzer Prompts
Understand the different beeping sounds emitted by the cleaner:
| State | Condition | Solution |
|---|---|---|
| Cleaner is on but not in water | Gentle beeping sound Rapid beeping sound Continuous beeping sound |
Normal condition. The cleaner needs to be charged. Contact after-sales service. |
| Cleaner remains motionless in the pool for a long period of time | Gentle beeping sound Rapid beeping sound Continuous beeping sound |
Take out the cleaner, clean the filter, bottom compartment, and other components before returning to the pool. Take out the cleaner, clean the filter, bottom compartment, and other components before returning to the pool. Contact after-sales service. |
| Cleaner is removed from the pool while operating normally | Gentle beeping sound | Clean after shutdown. |
| Shut down | Stop vocalization | Normal operation. |
9. Specifications
| Feature | Specification |
|---|---|
| Model | PC2332 |
| Brand Name | Blossom |
| Rated Operating Voltage | 11V |
| Power | 28W |
| Working Period (Full Power) | 130 minutes (actual time may vary) |
| Charger Input Voltage | 100-240V |
| Charger Input Frequency | 50/60HZ |
| Charger Output Voltage | 12.6V |
| Charger Output Current | 2A |
| Battery Capacity | 5000 mAh |
| Charging Time | 180 minutes |
| Maximum Clean Surface | 860 ft² |
| Maximum Filtration Capacity | 150 CFT/hour |
| Filter Tray Density | 178μm |
| Moving Speed | Approx. 17m/min |
| IP Level | IPX8 |
| Pool Water Temperature Range | 8°C - 37°C |
| Charging Environment Temperature Range | 0°C - 37°C |
| Maximum Water Depth | 8.8 FT |
| Dimensions (L*W*H) | 306mm * 197mm * 358mm (38X32X23 cm packaged) |
| Body Weight | 2.5 kg |
| Product Weight (packaged) | 3.3 kg |
| Storage Temperature Range | -20°C - 40°C |
| Pool Slope | 10°-15° |
10. Packing List
The product package includes the following items:
- 1 x Cleaning Machine Host
- 1 x Charger
- 1 x Filter Tray
- 1 x Recovery Hook
- 1 x Product Manual (this document)
11. User Tips
- The PC2332 is highly effective even for larger pools, providing thorough cleaning.
- Users appreciate the fast charging capability, allowing for quick turnaround between cleaning cycles.
12. Warranty & Support
For detailed warranty information, technical support, or service inquiries, please refer to the official product documentation or contact customer service.
A PDF version of this user manual is available for download: View User Manual (PDF)