EDON TIG-400

Contents

EDON IGBT Inverter Argon DC TIG-400 Welding Machine User Manual

Model: TIG-400 | Brand: EDON

1. Introduction

Thank you for choosing the EDON IGBT Inverter Argon DC TIG-400 Welding Machine. This professional-grade welding equipment is designed for high-performance TIG and MMA welding, offering stable output and advanced features for various metal processing tasks. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting to ensure optimal performance and longevity of your welding machine.

EDON TIG-400 Welding Machine front view

Figure 1: EDON TIG-400 Welding Machine

Video 1: 360-degree view of the EDON TIG-400 Welding Machine, showcasing its design and connection points.

2. Safety Information

Always adhere to the following safety precautions to prevent injury or damage to the equipment:

  • Wear appropriate Personal Protective Equipment (PPE), including welding helmet, gloves, protective clothing, and safety shoes.
  • Ensure adequate ventilation in the work area to disperse welding fumes.
  • Do not operate the machine in damp or wet conditions.
  • Verify that the power supply matches the machine's requirements (AC 3P 380V ±15% 50/60HZ).
  • Keep bystanders away from the welding area.
  • Disconnect power before performing any maintenance or adjustments.
  • Avoid touching live electrical parts.

3. Product Overview

The EDON TIG-400 is an advanced IGBT inverter welding machine featuring external ARC FORCE adjustment, slow ARC increasing/decreasing adjustment, and post-flow adjustment. It includes O.C.&O.H protection for long-term use and is capable of welding stainless steel and other easily oxidated nonferrous metals and alloy steels.

3.1 Control Panel

Control panel diagram of EDON TIG-400 welder

Figure 2: Control Panel Layout

  1. TIG & MMA Switch: Selects between TIG (Tungsten Inert Gas) and MMA (Manual Metal Arc) welding modes.
  2. 2T/4T Switch: Selects between 2-stroke and 4-stroke trigger modes for the TIG torch.
  3. Current Display: Digital display showing the welding current.
  4. Current Adjust: Knob to set the desired welding current.
  5. Arc Force: Knob to adjust the arc force, primarily used in MMA mode to prevent electrode sticking.
  6. Up Slope: Knob to set the time for the welding current to gradually increase from the initial current to the main welding current.
  7. Down Slope: Knob to set the time for the welding current to gradually decrease from the main welding current to the crater current.
  8. Post Flow Time: Knob to set the duration of shielding gas flow after the arc is extinguished, protecting the weld puddle and tungsten electrode from oxidation.

3.2 Included Accessories

EDON TIG-400 Welding Machine with accessories

Figure 3: Welding Machine and Accessories

The package typically includes the TIG-400 welding machine, TIG torch, ground clamp, electrode holder, and a basic welding mask.

4. Setup

  1. Unpacking and Inspection: Carefully unpack the welding machine and all accessories. Inspect for any signs of damage during transit. Report any damage to your supplier immediately.
  2. Power Connection: Connect the welding machine to a suitable AC 3P 380V ±15% 50/60HZ power supply. Ensure the power outlet is properly grounded and rated for the machine's input capacity (13.2KVA).
  3. Gas Connection (TIG Welding): For TIG welding, connect an argon gas cylinder to the 'GAS' inlet on the rear of the machine using a suitable gas hose and regulator. Ensure all connections are tight to prevent leaks.
  4. Ground Clamp Connection: Connect the ground clamp cable to the appropriate terminal on the front panel (usually marked with a ground symbol or '-'). Secure the ground clamp to the workpiece or welding table, ensuring good electrical contact.
  5. TIG Torch Connection: For TIG welding, connect the TIG torch cable to the designated TIG torch connector on the front panel. Ensure the gas line from the torch is also connected to the machine's gas output.
  6. MMA Electrode Holder Connection: For MMA welding, connect the electrode holder cable to the appropriate terminal on the front panel (usually marked with a '+' symbol).

5. Operating Instructions

  1. Power On: Flip the main power switch located on the rear panel to the 'ON' position. The digital current display should illuminate.
  2. Select Welding Mode: Use the 'TIG & MMA' switch (1) to select your desired welding process.
  3. Select Trigger Mode (TIG only): For TIG welding, use the '2T/4T' switch (2) to choose between 2-stroke (press and hold for arc) or 4-stroke (press to start, press again to stop) operation.
  4. Adjust Welding Current: Rotate the 'Current Adjust' knob (4) to set the desired welding current. The value will be shown on the 'Current Display' (3).
  5. Adjust Arc Force (MMA only): If in MMA mode, adjust the 'Arc Force' knob (5) to fine-tune arc stability and penetration.
  6. Set Up Slope Time (TIG only): Use the 'Up Slope' knob (6) to control the time it takes for the current to reach the set welding current. This helps prevent sudden arc starts and improves weld quality.
  7. Set Down Slope Time (TIG only): Use the 'Down Slope' knob (7) to control the time it takes for the current to decrease before the arc extinguishes. This helps prevent crater cracking.
  8. Set Post Flow Time (TIG only): Adjust the 'Post Flow Time' knob (8) to ensure sufficient shielding gas continues to flow after the arc stops, protecting the hot weld and tungsten.
  9. Begin Welding: With all settings configured and safety precautions in place, you can begin your welding operation.
  10. Power Off: After use, turn off the machine using the main power switch and disconnect the power supply. Close the gas cylinder valve.

6. Maintenance

Regular maintenance ensures the longevity and safe operation of your welding machine:

  • Cleaning: Periodically clean the internal components of the machine using dry compressed air to remove dust and metal particles. Ensure the machine is disconnected from power before cleaning.
  • Cable Inspection: Regularly inspect all welding cables, ground clamps, and torch components for wear, cuts, or damage. Replace damaged parts immediately.
  • Fan Check: Ensure the cooling fan on the rear panel is free from obstructions and operating correctly.
  • Connections: Check all electrical and gas connections for tightness and corrosion.

7. Troubleshooting

ProblemPossible CauseSolution
Machine does not power onNo power supply; Main switch off; Internal fuse blownCheck power connection; Turn on main switch; Contact service for fuse replacement
No welding arcPoor ground connection; Incorrect current setting; Torch/electrode issueEnsure good ground contact; Adjust current; Check torch/electrode for damage
Poor weld quality (TIG)Insufficient gas flow; Contaminated tungsten; Incorrect settingsCheck gas supply/flow; Clean/replace tungsten; Adjust current, slope, post-flow
Overheating indicator activeExceeded duty cycle; Blocked ventilationAllow machine to cool down; Clear ventilation openings

8. Specifications

Technical specifications table for EDON TIG-400

Figure 4: Detailed Technical Parameters

ParameterValueParameterValue
ItemPRO TIG-400Post Flow Time0s-10s
Input VoltageAC 3P 380V±15% 50/60HZNoload Voltage75V
Rated Input Current (MMA)26ARated Duty Cycle @40°C30%
Rated Input Current (TIG)20AEfficiency85%
Output Power Capacity (MMA)16.9KVAPower Factor0.93
Output Power Capacity (TIG)13.2KVAElectrode (mm)1.6-6.0mm
Output Current Range (MMA)20-380AProtection ClassIP21S
Output Current Range (TIG)10-400AInsulation ClassF
Up Slope Time0-10SSize600x330x520MM
Down Slope Time0-10SWeight30KG

9. User Tips

  • For TIG welding, always ensure your tungsten electrode is properly ground to a sharp point for a stable arc and precise welds.
  • When welding thin materials, use lower current settings and consider pulse welding if available (this model does not explicitly state pulse welding, but it's a general TIG tip).
  • Practice on scrap pieces of the same material and thickness as your project to dial in your settings before working on the final piece.
  • Keep your welding area clean and free of flammable materials.

10. Warranty and Support

The EDON TIG-400 Welding Machine comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please contact our customer service:

  • WhatsApp: +86 16633953613
  • Email: jinpin13@126.com

© 2024 EDON. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.