VGEBY 52V 25A 1200W Dual Drive Motor Controller Kit

Contents

VGEBY 52V 25A 1200W Dual Drive Motor Controller Kit User Manual

For Electric Bikes and Scooters

1. Safety Information

Please read all safety warnings and instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, serious injury, or property damage.

  • Always disconnect the battery before performing any installation, maintenance, or troubleshooting.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Keep the controller and display away from water and excessive moisture.
  • Do not attempt to open or modify the controller or display units. This will void the warranty and may cause damage or injury.
  • Warning: Pay close attention to battery charging and storage. Improper handling of batteries can pose a fire risk. Always use compatible chargers and follow battery manufacturer guidelines.

2. Product Overview

This kit provides a high-performance dual-drive motor control system for electric bikes and scooters, designed for enhanced power and smoother operation.

Complete Electric Bike Controller Kit components
Figure 1: Complete Electric Bike Controller Kit components, including two controllers, a display, a central control harness, and small accessories.

Package Contents:

  • 1 x Front Drive Controller
  • 1 x Rear Drive Controller
  • 1 x Display Unit
  • 1 x Central Control Harness
  • 3 x Accessories (connectors)

3. Installation and Setup

The installation process involves connecting the controllers to your motors, battery, and the display unit via the central control harness. Professional installation is recommended if you are unfamiliar with electric bike wiring.

3.1 Component Identification:

Close-up of one motor controller with various wiring harnesses
Figure 2: One of the motor controllers, showing the power input (yellow XT60 connector), motor phase wires (thick red, blue, green), Hall sensor wires, and other signal wires.
Close-up of the display unit with buttons and mounting bracket
Figure 3: The display unit, which mounts on the handlebars and provides operational feedback and controls.
Central control harness and small connectors
Figure 4: The central control harness, used to connect the display and other peripherals to the controllers, along with additional small connectors.

3.2 General Wiring Steps:

  1. Mount Controllers: Securely mount the front and rear drive controllers to your electric bike/scooter frame in a location protected from physical damage and moisture. Ensure adequate airflow for cooling.
  2. Connect Motors: Connect the three thick phase wires (typically green, blue, yellow) from each controller to the corresponding phase wires of your front and rear motors. Connect the smaller Hall sensor wires (usually a 5-pin connector) from each controller to the motor's Hall sensor port.
  3. Connect Battery: Connect the main power input wires (red and black, often with an XT60 connector) from both controllers to your 52V battery. Ensure correct polarity (red to positive, black to negative).
  4. Connect Central Control Harness: Connect the central control harness to the designated ports on both controllers. This harness will facilitate communication between the display and controllers.
  5. Connect Display: Mount the display unit on your handlebars. Connect the display cable to the central control harness.
  6. Connect Peripherals: Connect other components such as throttle, brake levers (with cut-off switches), and lights to the appropriate connectors on the controllers or central harness. Refer to the specific wiring labels on each connector.
  7. Initial Check: Before powering on, double-check all connections for security and correct polarity. Ensure no bare wires are exposed.

4. Operating Instructions

Once installed, the system is ready for operation. The display unit provides essential information and control over your electric bike/scooter.

4.1 Power On/Off:

  • To power on the system, press and hold the power button on the display unit.
  • To power off, press and hold the power button again until the display turns off.

4.2 Display Functions:

The display typically shows:

  • Current Speed
  • Battery Level Indicator
  • Assistance Level (if applicable)
  • Trip Distance / Odometer
  • Error Codes (if any)

Use the buttons on the display to cycle through information, adjust assistance levels, or access settings. Specific button functions may vary slightly; refer to the display's markings.

4.3 Riding:

  • Start riding by engaging the throttle or pedal assist (if equipped).
  • The dual drive controllers will manage power delivery to both motors for optimal performance.
  • The system supports speeds of up to 60 KM/H, depending on your motor's capabilities and local regulations.

5. Maintenance

Proper maintenance ensures the longevity and reliable operation of your controller kit.

  • Cleaning: Keep the controllers and display clean and free from dust and debris. Use a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
  • Connections: Periodically check all electrical connections to ensure they are tight and free from corrosion. Loose connections can lead to intermittent power or system failure.
  • Moisture Protection: While the controllers are designed to be robust, avoid prolonged exposure to heavy rain or submersion in water. If the system gets wet, allow it to dry completely before operating.
  • Cable Management: Ensure all cables are neatly routed and secured to prevent them from snagging or getting damaged during use.

6. Troubleshooting

If you encounter issues, try these basic troubleshooting steps:

ProblemPossible CauseSolution
System does not power onLoose battery connection, discharged battery, faulty power buttonCheck battery connections, charge battery, try pressing power button firmly.
Motor not respondingLoose motor phase/Hall sensor wires, faulty throttle/pedal assist, error code on displayCheck all motor connections, inspect throttle/PAS, note any error codes and consult support.
Intermittent powerLoose wiring, damaged cables, overheatingInspect all wiring for damage or loose connections. Ensure controllers have adequate cooling.
Display not showing correct informationLoose display cable, incorrect settingsCheck display cable connection. Power cycle the system.

If the problem persists after attempting these steps, contact customer support for further assistance.

7. Specifications

FeatureSpecification
BrandVGEBY
Item TypeElectric Bike Controller Kit
Voltage52V
Current25A
Wattage1200W
MaterialAluminum Alloy + PCB
Max Speed SupportUp to 60 KM/H (dependent on motor RPM)
Package Length32 cm
Package Width22 cm
Package Height5 cm
Package Weight0.704 kg

8. User Tips

  • Cable Organization: Use zip ties or cable wraps to keep all wires tidy and secure. This prevents damage and makes future maintenance easier.
  • Test Connections: After initial installation, perform a low-power test to ensure all components are functioning correctly before full operation.
  • Display Protection: Consider adding a screen protector to the display unit to prevent scratches and damage from impacts.

9. Warranty and Support

For warranty information and specific terms, please refer to the seller or your purchase documentation. Keep your proof of purchase for any warranty claims.

If you require technical assistance or have questions not covered in this manual, please contact the seller or manufacturer's customer support channel.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.