Flipsky 5045 120KV

Contents

Flipsky 5045 120KV 720W IP58 Waterproof Outer Rotor Motor User Manual

For Surfing Boats, Underwater Thrusters, and Hydro Efoils

1. Product Overview

The Flipsky 5045 120KV 720W IP58 Waterproof Outer Rotor Motor is a high-performance brushless motor designed for demanding aquatic applications. Its robust construction and IP58 waterproof rating ensure reliable operation in marine environments, making it suitable for surfing boats, underwater thrusters, and hydro efoils.

Flipsky 5045 120KV Outer Rotor Motor

Figure 1: Flipsky 5045 120KV Outer Rotor Motor

2. Specifications

ParameterValue
ModelΦ49.2×L45.0
Shaft DiameterΦ5 mm
KV Rating120KV
Voltage Range6-16S (LiPo)
Max Power720W
Rated Power500W
Max Current15A
Rated Current (I/A)10.5A
No Load Current0.3A
Coil Resistance (R/Ω)0.34
Coil Inductance (L/mH)0.43
Lead Wire14AWG
Plug Type4mm banana head (male)
Internal Structure12N/14P
Waterproof LevelIP58
Highest Working Temperature120°C
Flipsky 5045 Motor Dimensions Diagram

Figure 2: Dimensions of the 5045 Motor

Internal Hall Sensor Placement for Brushless Motor

Figure 3: Internal Hall Sensor Placement for Precise Detection and Positioning

The hall sensor is integrated into the motor core for precise detection, positioning, and temperature monitoring, ensuring smooth motor startup.

Stator Winding Design for Brushless Motor

Figure 4: Stator Winding Design

This motor utilizes multi-strand winding for better heat dissipation and to minimize the skin effect, which can lower efficiency in single-strand windings.

3. Setup and Installation

3.1 Mounting the Motor

  1. Ensure the mounting surface is flat and secure.
  2. Align the motor with the mounting holes. The motor typically uses M4 metric bolts for mounting.
  3. Secure the motor using appropriate M4 socket cap bolts (not included). Do not overtighten.
  4. If your motor includes a keyway on the shaft, ensure the key is properly seated when attaching a propeller or other drive components.
Flipsky 5045 Motor with Propeller

Figure 5: Motor with Propeller Attached

3.2 Electrical Connections

The motor comes with 14AWG lead wires terminated with 4mm male banana heads. Connect these to a compatible Electronic Speed Controller (ESC).

  • Connect the motor's three phase wires to the corresponding phase outputs on your ESC.
  • Standard wire configuration for brushless motors:
    • Blue = U (Phase A)
    • Yellow = V (Phase B)
    • Green = W (Phase C)
  • Ensure all connections are secure and insulated to prevent short circuits, especially in a wet environment.
  • Connect the ESC to your battery pack (6-16S LiPo recommended) and receiver/controller as per the ESC's instructions.
Flipsky 5045 Motor with Wires and Propeller

Figure 6: Motor with Lead Wires and Propeller

4. Operation

  1. Before initial operation, double-check all electrical connections and mounting points.
  2. Ensure the motor is clear of any obstructions.
  3. Gradually increase throttle to test motor rotation. If the motor spins in the wrong direction, consult your ESC manual for instructions on reversing motor direction (typically by swapping two of the three phase wires or through ESC programming).
  4. Monitor motor temperature during operation. The highest working temperature is 120°C. Avoid exceeding this limit to prevent damage.
  5. The motor has an IP58 waterproof rating, meaning it is protected from dust and can withstand continuous immersion in water up to a specified depth (typically 1 meter for IPx8). However, prolonged exposure to corrosive liquids or high-pressure water jets should be avoided.

5. Maintenance

  • After each use in water, rinse the motor with fresh water to remove salt, sand, or other debris.
  • Allow the motor to air dry completely before storage.
  • Periodically inspect the motor shaft and bearings for any signs of wear or corrosion.
  • Check all electrical connections for tightness and corrosion.
  • While the motor is designed for durability, avoid physical impacts or dropping the unit.

6. Troubleshooting

ProblemPossible CauseSolution
Motor not spinning or erratic operationLoose or incorrect wiring; ESC not configured correctly; damaged motor or ESC.Check all phase wire connections. Verify ESC settings (e.g., timing, motor type). Test with a known good ESC or motor if possible.
Motor overheatingOverloading the motor; incorrect propeller size; insufficient cooling; ESC timing too aggressive.Reduce load. Use a smaller propeller. Ensure adequate water flow for cooling. Adjust ESC timing.
Unusual noise or vibration from motorDamaged bearings; foreign object inside motor; unbalanced propeller.Inspect for foreign objects. Check propeller balance. If noise persists, bearings may need replacement.
Motor spins in wrong directionIncorrect phase wire connection or ESC setting.Swap any two of the three phase wires between the motor and ESC, or reverse direction via ESC programming.

7. User Tips

  • Internal Noise Check: One user reported hearing something inside the motor between the stator and rotor. If you notice unusual internal noises, it's advisable to inspect the motor for any obstructions or potential bearing issues before extensive use.
  • Motor Rotation Direction: If you require a specific rotation direction (Clockwise or Counter-Clockwise), remember that brushless motors can have their direction reversed by swapping any two of the three phase wires connected to the ESC, or by adjusting the settings in your ESC's programming.

8. Warranty and Support

For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Ensure you have your purchase details and product model information available.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.